Tekkeon ezSpeak ET6000 Manual de usuario
ET6000 User Guide
Handsfree
Bluetooth®Speakerphone
et6000_ug_fnl 10/26/06 4:17 PM Page 1
et6000_ug_fnl 10/26/06 4:17 PM Page 2
USER GUIDE
Contents
Overview..............................................................................................................................2
Getting Started ....................................................................................................................2
Unpacking ezSpeak ........................................................................................................2
Getting to Know ezSpeak ................................................................................................3
Setting Up ezSpeak..............................................................................................................4
Charging ezSpeak ..........................................................................................................4
Pairing ezSpeak to Your Mobile Phone ..........................................................................5
Mounting ezSpeak ..........................................................................................................6
Using ezSpeak ....................................................................................................................7
Powering ezSpeak ..........................................................................................................7
Making Calls ..................................................................................................................7
Receiving Calls................................................................................................................8
Ending Calls ....................................................................................................................9
Transferring Calls..........................................................................................................10
Adjusting the Volume....................................................................................................10
Muting ezSpeak ............................................................................................................11
Troubleshooting ................................................................................................................12
Limited Warranty ..............................................................................................................14
Disclaimer of Warranties ..............................................................................................14
FCC Statement ..................................................................................................................15
Customer Support ............................................................................................................16
et6000_ug_fnl 10/26/06 4:17 PM Page 1
2
Overview
ezSpeak™by Tekkeon is a Bluetooth®speakerphone with a digital display that gives you the freedom
to cut loose from your Bluetooth mobile phone. With advanced features like stored number redial,
last number redial and voice dialing, you can use ezSpeak to make and receive calls without ever
touching your mobile phone. And, you can use ezSpeak in your car, at home, or anywhere that is
convenient for you.
ezSpeak is designed with Bluetooth v1.2 technology, and is backward compatible with all Bluetooth
v1.1 devices.
Getting Started
Unpacking ezSpeak
Your ezSpeak package includes the following:
User guide (not shown)
An optional wall charger is available from the Tekkeon on-line store at www.tekkeon.com.
ezSpeak
Visor clip Swivel (for visor clip)
Car charger
et6000_ug_fnl 10/26/06 4:17 PM Page 2
3
USER GUIDE
Getting to Know ezSpeak
Digital Display
Provides caller ID, call
status, indication of device
connection, volume level,
and low battery indication
Power/End Call Button
Used to turn on/off
ezSpeak, reject calls
and end calls
Microphone
Answer Button
Used to initiate pairing,
connect/disconnect the
paired phone, and
make/receive calls
Speaker
Volume Up/Volume Down
Increases the speaker volume, mutes/unmutes
the microphone, and enables scrolling through
stored numbers
Charging Lamp
Indicates when ezSpeak is
being charged or fully charged
Charging Jack
Input for car charger
or optional wall
charger to charge
ezSpeak
et6000_ug_fnl 10/26/06 4:17 PM Page 3
4
Setting Up ezSpeak
Before using ezSpeak, you must:
• Charge ezSpeak
• Pair ezSpeak to your mobile phone
• Mount ezSpeak to your visor (for in car use)
Directions for each of these activities are provided in the following three sections. Once these steps are
completed, you will be ready to use ezSpeak!
Charging ezSpeak
Before using ezSpeak, you must charge the device for a minimum of two hours. When fully charged, the
battery provides up to ten hours of talk time and up to 220 hours of standby time. When the battery is at
less than 5% of capacity, the low battery icon will appear on the display.
1. Plug the car charger into the charging jack on the end of ezSpeak.
2. Plug the car charger into the 12V charging outlet in your car.
The red charging LED will light while
ezSpeak is charging. When the device is fully charged (in approximately 2 hours), the red LED will
turn to to green.
3. Unplug the car charger from the charging outlet.
et6000_ug_fnl 10/26/06 4:17 PM Page 4
5
USER GUIDE
Pairing ezSpeak to Your Mobile Phone
Pairing is the process of linking ezSpeak with your Bluetooth mobile phone or other Bluetooth device that
supports a headset and/or handsfree profile. Before using ezSpeak with your mobile phone you must
pair the devices. After this process is complete, you can use ezSpeak with your paired mobile phone.
You can pair ezSpeak with up to seven Bluetooth devices. Once each device is paired with ezSpeak, you
must disconnect the paired phone or device to connect to a different phone or device. While connected
to a different paired device, ezSpeak will not be connected to other paired devices.
BEFORE YOU PAIR ezSPEAK, ENSURE THAT THE BATTERY IS FULLY CHARGED, AND REVIEW THE
INSTRUCTIONS IN YOUR MOBILE PHONE USER GUIDE FOR PAIRING YOUR MOBILE PHONE TO A
BLUETOOTH DEVICE.
To Pair the Devices
1. With the ezSpeak turned on, press and hold until “Ready to Pair” appears on the display
(approximately five seconds).
2. With the mobile phone turned on, initiate the Bluetooth device-pairing (discovery) feature. Refer to the
mobile phone/device user guide for instructions on initiating this feature.
3. Follow the mobile phone/device prompts, and when prompted for the passkey (also called passcode
or BT PIN), enter 1234 (the ezSpeak passkey).
When pairing is complete, ezSpeak is placed in
standby mode, and ET6000 appears on the display.
4. Press to connect ezSpeak with the paired phone.
“Connecting,” followed by the name of the
phone, will appear on the display to indicate the phone is connected to ezSpeak.
NOTE: Once you’ve paired your phone with ezSpeak, you don’t need to repeat this entire procedure.
Simply follow step 4 above to connect to the last paired phone, or the last connected phone.
et6000_ug_fnl 10/26/06 4:17 PM Page 5
6
Mounting ezSpeak
When used in a car, ezSpeak is designed to be mounted to your car visor. You can use the visor clip with
or without the optional swivel clip.
To Mount ezSpeak with the Visor Clip
1. Attach the visor clip to ezSpeak by sliding the clip into the
bracket on the rear of ezSpeak as shown.
2. Slide the clip onto your car visor.
To Mount ezSpeak with the Visor Clip and Swivel
1. Remove the small bracket from the visor clip by lifting up on the prong and pulling the small bracket
away from the visor clip.
2. Attach the swivel bracket to the visor clip by sliding the
bracket onto the clip while lifting the prong. The bracket
will snap into place.
3. Attach the swivel bracket into the bracket on the rear of
ezSpeak as shown.
4. Slide the clip onto your car visor, as shown above,
adjusting the position as needed.
5. Turn the swivel screw to tighten the clip as shown.
et6000_ug_fnl 10/26/06 4:17 PM Page 6
7
USER GUIDE
Using ezSpeak
Powering ezSpeak
To Turn On ezSpeak
1. Press and hold approximately two seconds until the display lights up and “ET6000” appears
on the display.
NOTE: To conserve power, the display will turn off after being idle for approximately eight seconds.
To view the display, simply press .
To Turn Off ezSpeak
1. Press and hold approximately four seconds until “Power Off” appears on the display and
ezSpeak turns off.
Making Calls
You can make calls from your mobile phone, or directly from ezSpeak using the last number redial
feature, voice dialing commands, or the stored number redial feature.
NOTE: ezSpeak must be connected with the paired phone (the phone name appears in the display).
If ET6000 is displayed instead of the phone name, you must connect to ezSpeak before making a call.
To Make Calls from Your Mobile Phone
1. Dial the number from your mobile phone.
The call is automatically connected to your ezSpeak.
To Make Calls Using Last Number Redial (if supported by your mobile phone)
1. Press twice quickly to redial the last number dialed from your mobile phone.
The number is
called, and “Redial, and then “Calling” appear on the display.
et6000_ug_fnl 10/26/06 4:17 PM Page 7
8
To Make Calls Using Voice Dialing (if supported by your mobile phone)
1. Press .
“Voice Dial” appears on the display and your phone is put into voice dialing mode.
2. After you hear a beep (usually between one to four seconds), speak the name of the person you wish
to call.
You will hear the spoken name (if provided by your phone) and the call is automatically
connected to ezSpeak.
NOTE: The voice dial feature must be activated and the voice tag must be recorded before using this
function.
TIP: In a noisy environment where the noise may interfere with voice commands, you should dial from
the mobile phone keypad, or use any of the other advanced calling features to make the call from
ezSpeak.
To Make Calls Using Stored Number Redial
1. Press for two seconds to enter Memory mode.
The last received number will appear first.
2. Press or to scroll through the numbered list of the last nine received calls.
3. Press to dial selected number.
“Calling” appears on the display and the call is automatically
connected to ezSpeak.
Receiving Calls
When you receive a call on your mobile phone, both ezSpeak and your mobile phone will ring. You can
either answer the call, or reject the call and send the caller to voice mail (if available).
If the Call Waiting feature is supported by your phone, you can answer an incoming call while you are
connected on another call. In this case, the connected call is placed on hold and the incoming call is
connected. While both calls are connected, you can toggle between both.
et6000_ug_fnl 10/26/06 4:17 PM Page 8
Otros manuales para ezSpeak ET6000
1
Tabla de contenidos
Otros manuales de Teléfono de Tekkeon
