Tekkeon ezTalker mini ET2000 Manual de usuario
ET2000
User Guide
Cord-Free Headset for Mobile Phones
Bluetooth mobile headset
Inside Front
1
USER GUIDE
ezTalker miniTM by Tekkeon is a miniature cord-free headset that enables
comfortable, handsfree communication with your BluetoothTM mobile phone.
ezTalker mini works with your Bluetooth-ready mobile phone to provide clear,
high-quality communication.
While using your ezTalker mini headset, you can store your mobile phone in
your pocket, backpack, or briefcase—just about anywhere in close proximity that
is convenient for you.
Unpacking ezTalker mini
Your ezTalker mini package includes the following:
➀ezTalker mini Headset
➁Power Adapter
➂ezEarhook
➃ezFit Earpiece (2)
➄User Guide and QuickStart
(not shown)
➀
➁
➂
➃
2
Getting to Know ezTalker mini
Getting Started
Before using ezTalker mini, you must:
•Charge ezTalker mini
•Pair ezTalker mini to your mobile phone
•Fit ezTalker mini to your ear
Directions for each of these activities are provided in the following three sections.
Once these steps are completed, you will be ready to use ezTalker mini!
TALK Button
Used for turning headset on/off,
pairing, and making/receiving calls
Amber and Blue LEDs
Provides visual indication of headset
status: power on/off, pairing mode, muting
mode, charging mode, and low battery
Charging Jack
Input for power adapter to charge the headset
Volume Control
Used to adjust the speaker volume, mute the
microphone and initiate last number redial
Speaker
Microphone
3
USER GUIDE
Charging ezTalker mini
Before using ezTalker mini, you must charge the headset for approximately two hours. When fully
charged, the battery provides up to five hours of talk time and up to 120 hours of standby time.
To Charge the Headset
1. Remove the rubber plug that covers the charging jack on the upper
left side of the headset.
2. Plug the power adapter into the charging jack.
3. Plug the power adapter into a wall outlet. While the headset is
charging, the amber LED on the headset will remain on. When the
headset is fully charged, the amber LED will turn off.
4. Unplug the power adapter from the wall outlet and the headset.
5. Place the rubber plug in the charging jack.
BATTERY INDICATION: When the battery is low (less than 10% of capacity), the amber LED will
flash and you’ll hear a beep every 32 seconds.
Pairing ezTalker mini to Your Mobile Phone
Pairing is the process of linking the headset with your Bluetooth mobile phone. Before using
ezTalker mini with your mobile phone you must pair the devices. After this process is complete,
you can use the headset only with its paired mobile phone. To use ezTalker mini with a different
mobile phone, you must repeat the pairing process with the new mobile phone. In this case, the
headset will no longer work with the original mobile phone.
BEFORE YOU PAIR THE HEADSET, ENSURE THAT THE BATTERY IS FULLY CHARGED, AND REVIEW THE INSTRUCTIONS
IN YOUR MOBILE PHONE USER GUIDE FOR PAIRING YOUR MOBILE PHONE TO A BLUETOOTH HEADSET.
Figure 1.
Power adapter connected to
ezTalker mini.
4
To Pair the Devices
1. Turn on the mobile phone and place it next to the headset.
2. Initiate the Bluetooth device-pairing (discovery) feature on the mobile phone. Refer to the mobile
phone user guide for instructions on initiating this feature.
3. With the headset turned off, press and hold the TALK button approximately five seconds, until the
blue and amber LEDs flash alternately or until you hear the PAIRING tone.
4. Release the TALK button. The headset is now in Pairing Mode.
5. Follow the mobile phone prompts, and when prompted for the passkey (also called passcode or
BT PIN), enter 0000 (the ezTalker mini passkey). When pairing is complete, the headset will be
placed in Standby Mode, ready to make and receive calls, the amber LED will turn off, and the
blue LED will flash at two-second intervals.
To Cancel Pairing Mode
While you are in pairing mode, you can cancel the pairing process and turn off the headset.
1. While in pairing mode, press and hold the TALK button approximately three seconds until both
LEDs turn off or you hear the OFF tone.
Fitting ezTalker mini On Your Ear
ezTalker mini is designed to fit comfortably in your ear. For added comfort, you can change the ezFit
Earpiece. For added stability, you can add the ezEarhook.
To Place the Headset On Your Ear
1. Place the ezTalker mini speaker in your ear with the microphone angled toward your mouth. The
headset should fit snugly in your ear and remain in your ear when you move your head. However,
if the ezEarpiece is too large for your ear, you can replace it with the medium size provided,
and/or add the ezEarhook.
5
USER GUIDE
To Replace the ezFit Earpiece
1. To remove the ezFit Earpiece, hold the plastic and gently pull toward you.
2. Snap the other ezFit Earpiece into place.
To Add the ezEarhook
1. Position to hole on the end of the ezEarhook over the stem on the rear of ezTalker and push to
snap the ezEarhook into place.
2. If the ezEarhook is positioned for your right ear, swivel the hook counter-clockwise
until the hook is to the right of the earpiece and rotate the top portion of the hook
to wear on your left ear. If the ezEarhook is positioned for your left ear, swivel the
hook clockwise until the hook is to the left of the earpiece and rotate the top
portion of the hook to wear on your right ear.
3. Mold the soft plastic on the ezEarhook as needed for a better fit.
To Remove the ezEarhook
1. Gently pull the ezEarhook away from the headset stem until it separates from the headset.
Powering ezTalker mini
To Turn On the Headset
Press and hold the TALK button approximately four seconds until the blue LED flashes or until you
hear the ON tone. The headset turns on and is placed in standby mode, ready to make and receive
calls. While the headset is on and in standby mode, the blue LED will flash at two-second intervals.
Figure 3.
ezEarhook
(positioned for
left ear)
Figure 2.
ezTalker mini with
ezFit Earpiece
6
To Turn Off the Headset
When the headset is on, press and hold the TALK button approximately four seconds until the blue
LED turns off or until you hear the OFF tone. The headset turns off.
Making Calls
You can make calls from your mobile phone, or directly from ezTalker mini using the last number
redial feature or voice dialing commands (if these features are supported by your mobile phone.)
To Make Calls From Your Mobile Phone
1. Dial the number from your mobile phone. The call is automatically connected to your headset.
To Make Calls Using Last Number Redial (if supported by your mobile phone)
1. Press and hold either VOLUME button (+/-) for three seconds while the phone is in standby mode.
The last number dialed from your mobile phone will be dialed automatically if this feature is
supported by your mobile phone. Note that this operation is used to mute/unmute your phone
when the headset is in talk mode.)
To Make Calls Using Voice Dialing (if supported by your mobile phone)
1. Press the TALK button on your headset.
2. When prompted by the mobile phone (usually about five seconds), speak the name of the person
you wish to call. The call is automatically connected to your headset.
TIP: In a noisy environment, you should dial the number from the mobile phone keypad as the loud
background noise may interfere with voice commands.
7
USER GUIDE
Receiving Calls
When you receive a call on your mobile phone, you will hear the mobile phone ring before you hear
the ring tone through your headset as there is a small delay before the headset recognizes the
incoming call. If you do not wish to answer the call, you can use the Call Reject feature to reject the
call and send the caller to voice mail (if available).
To Receive a Call
1. When you hear ring tone on your headset, press the headset TALK button. The call is
automatically connected to your headset.
To Reject an Incoming Call (if supported by your mobile phone)
1. When you hear ring tone on your headset, press and hold the TALK button for four seconds until
you hear two soft beeps to reject the call.
NOTE: For some mobile phones, you must configure the phone to answer calls directly on your
Bluetooth headset. Refer to the mobile phone user guide for instructions for initiating this feature.
Ending Calls
1. When you have finished your call, press the headset TALK button. The call will be disconnected.
Transferring Calls
You can transfer calls from your mobile phone to your headset.
To Transfer Calls from Your Mobile Phone To The Headset
1. With the call connected to your mobile phone, press the TALK button on your headset.
8
Adjusting the Volume
The volume can be adjusted using the volume controls
on ezTalker mini or your mobile phone.
To Increase the Volume
1. Press and release the top VOLUME button +.
To Decrease the Volume
1. Press and release the bottom VOLUME button -.
Muting ezTalker mini
You can mute and un-mute the microphone temporarily so that you cannot be heard by the
connected party.
To Mute the Headset
1. Press and hold either VOLUME button (+/-) for three seconds. While the headset is muted, you
will hear a beep every four seconds.
To Un-Mute the Headset
1. When the microphone is muted, press and hold either VOLUME button (+/-) for three seconds.
Figure 4.
Volume buttons
Otros manuales para ezTalker mini ET2000
3
Tabla de contenidos
Otros manuales de Auriculares de Tekkeon
Tekkeon
Tekkeon ezTalker ET3000 Manual de usuario
Tekkeon
Tekkeon ezTalker mini ET2000 Manual de usuario
Tekkeon
Tekkeon ezTalker mini ET2000 Manual de usuario
Tekkeon
Tekkeon ezTalker ET1000 Manual de usuario
Tekkeon
Tekkeon ezTalker mini ET2000 Manual de usuario
Tekkeon
Tekkeon ezTalker ET3000 Manual de usuario
Tekkeon
Tekkeon ezTalker ET1000 Manual de usuario
