Teka CartMaster wall 1-IFA Manual de usuario

Operating instructions

(Translation of the original operating instructions)

CartMaster wall 1 - IFA

CartMaster wall 2 - IFA

TEKA Absaug- und Entsorgungstechnologie GmbH, Millenkamp 9, D-48653 Coesfeld,

Tel.: +49 2541-84841-0, E-Mail: info@teka.eu, www.teka.eu

Table of contents

1. General 3

2. Description of the system elements 4

2.1. Illustration of the system elements 4

2.2. Functionality of the system 5

2.3. Intended use 5

2.4. Residual risk 5

3. Safety instructions 6

3.1. Definition of the hazard symbols 6

3.2. General safety instructions 6

4. Storage, transport and installation of the device 7

4.1. Mounting of the unit to the wall 7

5. Commissioning 9

5.1. Connecting the suction line and exhaust air line 10

5.2. Electrical connection 11

5.3. Precoating of the filter cartridges 12

5.4. Connecting the compressed air supply 12

5.4.1. Compressed air supply for the cleaning of the filter cartridges 12

6. Operating the system 13

6.1. Explanation of the operating elements 13

7. Maintenance 14

7.1. Reset to maintenance state 15

7.2. Cleaning the filter cartridges 15

7.3. Replacing the filter cartridges 16

7.4. Emptying the dust collecting tank 21

7.5. Draining the condensate 22

7.6. Precoating of new filter cartridges 23

7.7. Cleaning the copper baffle plate 24

8. Dismantling / Disposal 25

9. Diagnostics and troubleshooting 25

10. List of spare parts 27

11. Technical data 28

12. EC declaration of conformity 29

13. Training protocol 30

14. Maintenance intervals 31

14.1. Usage-related maintenance 31

14.2. General maintenance 31

14.2.1. Visual inspection of the device 32

14.2.2. Visual inspection of the pipelines for dust deposits 32

14.2.3. Visual inspection of the pneumatic pipes 32

14.2.4. Functional test of the device 33

BA_CartMaster-Wand_1-und-2_IFA_20230808_EN

08.08.2023

14.2.5. Electrical test of the electrical lines and earthing connections 33

1. General

Congratulations on purchasing the product from TEKA.

Our engineers ensure that our devices reflect the state of the art through continuous development.

Nevertheless, misuse or misconduct can endanger your safety. Please observe the following for a

successful use of the device:

Only authorised and instructed personnel can carry out transport, operation,

maintenance and repair of the device. The operator must ensure that the operating

personnel take note of these instructions.

Please read these instructions before operating the device, and observe the safety

precautions to avoid injury!

Store this manual in a safe place! These instructions are to be regarded as a component

of the product!

Adhere to all product notes!

Modifications or conversions that the operator carries out at the device without the

consent of the manufacturer, can lead to new safety hazards or to the loss of warranty

claims.

Observe the manufacturer’s instructions. Contact the manufacturer in case of any

uncertainty:

Tel: +49 2541-84841-0

E-mail: [email protected]

BA_CartMaster-Wand_1-und-2_IFA_20230808_EN

08.08.2023

2. Description of the system elements

2.1. Illustration of the system elements

Installation example:

Z.Nr. 12471707

Pos.1

Pos.2

Pos.3

Pos.4

Pos.5

Filter housing

Cleaning housing

Fan

Suction nozzle

Exhaust air nozzle

Pos.6

Pos.7

Pos.8

Pos.9

Pos.10

Connection for compressed air

Drain valve for compressed air

Dust collecting tank

Toggle lever

Wall console

BA_CartMaster-Wand_1-und-2_IFA_20230808_EN

08.08.2023

2.2. Functionality of the system

The filter unit serves to suck off and filter polluted air (according to the intended use). The air is purified

on the surface of the filter cartridge in the filter section of the unit. The separated dust is collected in a

dust collecting tank. An automatic filter monitoring indicates when a cleaning or a replacement of the

filters is necessary. The purified air is led outside via the exhaust air pipe or back into the working room.

2.3. Intended use

The device is intended for commercial use. If the device is made publicly accessible, it must never be

operated unsupervised by authorized personnel, authorized by the operator.

The filter unit is intended for extraction and filtration of dusts and fumes that result from thermal joining

and cutting of metals. The filter unit is amongst others suitable for separating welding smokes of

unalloyed and alloyed steels as well as of high-alloy chromium-nickel steels and therefore meets the

highest welding fume separation category “W3” according to DIN EN ISO 21904-1 / -2.

WARNING

Improper use can damage parts and be a danger to life and limb!

The device must not be used for the extraction of oil-laden welding fume, explosive dust

and gases, hybrid mixtures, glowing or burning substances, gases, water, etc. The

device must not be operated in explosive zones.

Dangers arising from fire.

If the sucked medium is combustible fume or dust, the operator must determine

beforehand which fire protection measures are to be taken.

2.4. Residual risk

CAUTION

Danger due to possible hazardous materials in the exhaust air flow.

Because the unit does not monitor the quality of the air in the exhaust air flow, we

recommend that you always guide the exhaust air flow exiting our unit to areas (e.g. to the

outside into the open air) in which there is no danger to any living being. To do this, it is

necessary to fit a suitable exhaust air line at the filter unit.

BA_CartMaster-Wand_1-und-2_IFA_20230808_EN

08.08.2023

3. Safety instructions

3.1. Definition of the hazard symbols

The device is constructed according to the state of the art and the recognised safety regulations.

Nevertheless, during use threats to life and limb of the user or other persons may arise. The impairment

of the machine or other property are also possible. In these instructions we warn by using corresponding

indications.

WARNING

These instructions are made in case of risks that can lead to injury or death.

CAUTION

These instructions are made in case of risks that can lead to injury.

NOTICE

These instructions are made in case of risks that can lead to material damages.

Information notes are no hazard warnings; they call attention to useful information.

3.2. General safety instructions

WARNING

Dangers arising from improper use / unauthorised operations.

The operator must ensure that their authorised personnel are familiar with all the safety

indications in this manual in advance. The operator is responsible for ensuring that all work

is carried out by authorised and qualified personnel. We therefore recommend using the

training protocol on the last page for that purpose (see chapter “Training protocol”).

Laymen are allowed to operate the device after having received the necessary instructions.

But they are not allowed to carry out any installation, repair or maintenance work.

Dangers arising from fire.

In case of fire, if possible, switch the unit immediately off or disconnect it from the power

supply. Fire extinguishing measures which the operator is obliged to determine beforehand

must be initiated immediately.

BA_CartMaster-Wand_1-und-2_IFA_20230808_EN

08.08.2023

WARNING

Dangers arising from electricity.

The operator must ensure that electrical plants and equipment are only built, modified and

maintained by a qualified electrician or under the direction and supervision of a qualified

electrician. Do not work on components if you are not sure that these are disconnected. If

necessary, disconnect the device from the electric power supply and secure it against

unauthorized restarting.

4. Storage, transport and installation of the device

WARNING

Risk of injury from tilting or unmounted components when stored or transported.

The device must be secured against tilting and slipping when it is stored or transported. Do

not stand under or next to the floating load. Lift trucks, forklift trucks and transport cranes

must have a sufficient minimum load bearing capacity.

Risk of injury arising from the falling unit at its destination.

The unit must be firmly mounted to the destined wall. The wall must be vibration-free and

vertical. The operator must check if the wall provides a sufficient bearing capacity.

NOTICE

Damage or functional impairment of the unit due to climatic influences.

The unit must be stored in a dry place and protected against moisture during transport. As a

matter of principle, the filter unit is not designed to be installed outdoors. In this case contact

the manufacturer in order to find out if a caping or a trace heating system are necessary.

BA_CartMaster-Wand_1-und-2_IFA_20230808_EN

08.08.2023

4.1. Mounting of the unit to the wall

Wall brackets are already attached to the filter unit upon delivery.

● The two other wall brackets must be screwed to the wall. Pay attention to an identical distance

"X".

● Put the filter unit with its wall brackets on the wall brackets attached to the wall and screw them

by means of the delivered screws.

BA_CartMaster-Wand_1-und-2_IFA_20230808_EN

08.08.2023

5. Commissioning

WARNING

Dangers arising from a defective condition of the unit.

Make sure that the measures described in this chapter are completed before the

commissioning of the unit. All doors of the unit must be closed and all necessary connections

must be attached before turning the unit on. Do not operate the unit if any components are

defective, missing or damaged. Check the orderly condition of the unit before switching it on.

The unit must not be operated without a filter element.

NOTICE

Damaged supply lines.

Make sure that the supply lines are protected against damage by forklift trucks and similar

events. Protect all supply lines from heat, moisture, oil and sharp edges.

BA_CartMaster-Wand_1-und-2_IFA_20230808_EN

08.08.2023

5.1. Connecting the suction line and exhaust air line

For extracting the contaminated air, a suction line must be connected to the suction nozzle (see chapter

2.1).

CAUTION

Danger for the respiratory tract arising from polluted ambient air. Dust deposits in the

suction pipe are possible.

Only operate the system if the necessary suction line is fitted. The suction line must be

dimensioned according to the application in such a way that, if possible, no dust deposits

occur in the suction line. If this has not already been carried out by TEKA, a suitably qualified

employee must be consulted. If the suction line includes extraction elements (e.g. suction

arms, pipe grills, etc.), these must also be included in the layout. If this is the case then users

must be informed of whether extraction elements can be used simultaneously and, if this is

possible, then which. The regulating devices (e.g. throttle valves) of each single extraction

element must also be set appropriately during the final commissioning.

Depending on the application, the suction pipe must be equipped with extraction elements (suction arm,

extraction hose, round duct grille, etc.). When using a capture element with an extractor cowl, the

extractor cowl must follow the weld seam, if possible by using the movement of the welding fume

caused be thermal influences.

: You have to make sure that connections between the workpiece and the suction

hood (and in general between the workpiece and the filter unit) are avoided in order to prevent

the welding current from flowing back to the welding machine via the protective conductor of the

filter unit.

The exhaust air pipe must be attached to the exhaust nozzle (see chapter 2.1).

WARNING

Danger to life when reaching the fan impeller.

The required exhaust air pipe must be attached before the commissioning.

The assembly of a suction arm is described in the separate operating manual.

BA_CartMaster-Wand_1-und-2_IFA_20230808_EN

08.08.2023

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Campana de ventilación de Teka

Teka

Teka TL-2000 Manual de usuario

Teka

Teka DLH 686 Manual de usuario

Teka

Teka GFL 651 EOS Manual de usuario

Teka

Teka DX series Manual de usuario

Teka

Teka C 610 Manual de usuario

Teka

Teka DSJ 980 Manual de usuario

Teka

Teka DQ2 Manual de usuario

Teka

Teka DH2-90 Manual de usuario

Teka

Teka DY-90 Manual de usuario

Teka

Teka DH-60 Guía de configuración

Teka

Teka DHB-60 Manual de usuario

Teka

Teka CC 40 Manual de usuario

Teka

Teka DVL VR.01 Manual de usuario

Teka

Teka DVT TBS Series Manual de usuario

Teka

Teka DG 80 Series Manual de usuario

Teka

Teka DV-80 S/S Manual de usuario

Teka

Teka CNL 6415 PLUS Manual de usuario

Teka

Teka DVN 64030 TTC BK Manual de usuario

Teka

Teka DVN 67050 TTC BK Manual de usuario

Teka

Teka DH2 90 ISLA Manual de usuario

Teka

Teka DPL 110 ISLA Manual de usuario

Teka

Teka DVT 50 Series Manual de usuario

Teka

Teka DJ-60 Manual de usuario

Teka

Teka DG-60 Manual de usuario

Manuales populares de Campana de ventilación de otras marcas

emmeti

emmeti RECUPA MED A-140 Guía

Nibe

Nibe F135 Manual de usuario

Kuppersberg

Kuppersberg INTRO 60 Instrucciones de instalación y mantenimiento

Zephyr

Zephyr Spruce AK9834BS Guía de instalación

Hisense

Hisense MH6INBG Manual de usuario

Miele

Miele DA 1255 Manual de usuario

Broan

Broan 46000 Manual de usuario

GE Profile PV977 Instrucciones originales

FALMEC

FALMEC FFRIA24W5FS Manual de usuario

Whirlpool

Whirlpool RH2600XL-1 SERIES Manual de usuario

Küppersbusch

Küppersbusch DX ISLA Manual de usuario

ETNA

ETNA AV360RVS Manual de usuario

JUNO

JUNO JDF603E6 Manual de usuario

Miele

Miele DA 6708 D Manual de usuario

Tricity Bendix

Tricity Bendix LE 150 Manual

AEG

AEG X68163BV1 Manual de usuario

AEG

AEG 125 D Manual de usuario

Smeg

Smeg KSEV97X Manual de usuario