Teka E/60.2 Guía del usuario
26
Code Nº: PRM-00-0001
Revised / Date: 2006
INSTALLER’S MANUAL
Page Nº: 26 of 95
3 HOBS
When fitting a hob, installers should bear in mind the following series of important
recommendations in order to ensure the safety and correct working of the appliance:
During fitting, recessed hobs should be handled with care to prevent damage to the edges
or the glass surface of vitroceramic models.
With vitroceramic models, carefully check the glass surface to ensure there are no cracks.
Should there be even the slightest crack, do not proceed with installation.
If the hob is to be recessed over an oven, carefully follow all specifications indicated to
ensure correct ventilation.
Before installing, ensure that the gas supply characteristics are compatible with the
regulations indicated on the specification plate (gas type and pressure).
Installation and maintenance of the hob should be carried out by qualified personnel in
accordance with existing regulations.
Cabinet adhesives should be resistant to temperatures of 100ºC (Y type protection against
overheating, in compliance with the EN 60335-2-6 standard).
Minimum distances between the hob and extractor hood should be strictly observed: 65 cm
for electric hobs 70 cm for gas and mixed hobs.
Recess measurements should be similarly observed.
Recessed hobs with reinforced plates should be installed more than 15 cm away from side
walls. All other hobs should be installed at a distance of more than 10 cm.
The hobs referred to in this installation manual are compatible with TEKA ovens. In this
case consult the corresponding manual before installing.
The installation process does not differ much from model to model. Below are installation
instructions for each model in the range with both independent and ME controls and for gas,
electric and mixed models.
27
Code Nº: PRM-00-0001
Revised / Date: 2006
INSTALLER’S MANUAL
Page Nº: 27 of 95
3.1 INSTALLATION OF HOB:
E/60.2 AND ES/60.2 E/50
(1) Minimum distance to wall (1) Minimum distance to wall
(2) Minimum ventilation distance (2)Minimum ventilation distance
(3) Space for recess (3) Space for recess
28
Code Nº: PRM-00-0001
Revised / Date: 2006
INSTALLER’S MANUAL
Page Nº: 28 of 95
SM AND CG, EC AND CGC, ECC
(1) Minimum distance to wall
(2) Minimum ventilation distance
(3) Space for recess
CG LUX 70
CG LUX 60
29
Code Nº: PRM-00-0001
Revised / Date: 2006
INSTALLER’S MANUAL
Page Nº: 29 of 95
VITROCERAMIC HOBS
(1) Minimum distance to wall (1) Minimum distance to wall
(2) Minimum ventilation distance (2) Minimum ventilation distance
(3) Space for recess (3) Space for recess
Depending on the model in question, the recessing system is designed for cabinets with a work
surface thickness of 20, 30 and 40 mm. In the event that a separation board is not required, the
TT 620
TR 620
TR 620, TZ620 AND TR640TR 620, TZ620 AND
TR640
30
Code Nº: PRM-00-0001
Revised / Date: 2006
INSTALLER’S MANUAL
Page Nº: 30 of 95
induction models nºs IR/IT 635, IR/IT 645 and IR 735 include a suplementary casing which shoud
be fitted when installing the appliance under a drawer.
31
Code Nº: PRM-00-0001
Revised / Date: 2006
INSTALLER’S MANUAL
Page Nº: 31 of 95
Plate NºTR 932
Plates Nºs VI TC 60 2I AND VI TC 60 4I
1. Minimum distance between adjacent walls
2. Interior cut measurement
3. Exterior cut measurement
4. External measurement of worksurface
1. Minimum distance between ajacent walls
2. Interior cut measurement
3. Exterior work surface measurement
32
Code Nº: PRM-00-0001
Revised / Date: 2006
INSTALLER’S MANUAL
Page Nº: 32 of 95
IR 622, IZ 622, IT622
(1) Minimum distance to wall (2) Minimum ventilation distance (3) Space for recess
NOTE: Induction hobs should not be installed above an oven that does not feature forced
ventillation.
The installation process is the same as for vitroceramic
hobs, bearing in mind it will be necessary to take
greater precautions to ensure improved ventilation for
the recess space.
Ventilation openings will need to be thermally isolated
using the insulating blanket supplied with the hob.
This insulating blanket prevents hot air mixing with the
cold air being sucked in.
Warning! This blanket must not cover ventilation
outlets, preventing the evacuation of air.
Avoid excessive heat build up in the hob.
33
Code Nº: PRM-00-0001
Revised / Date: 2006
INSTALLER’S MANUAL
Page Nº: 33 of 95
3.2 FITTING THE HOB TO ITS RECESS
-{}-
Cristal Gas Series
-{}-
C-SerieSoftplate
B - How to fit this plate in a 60cm
cabinet
D - 60 cm cabinet
E - Detail
The minimum vertical distance from
the hob to the cabinet is 600 mm.
The fitting process is identical to that for other
models.
1) Attach seal “J”.
2) Fix the four clips “G”using the two tabs “P”,
in the spaces “O”in the hob.
3) Tighten the screws “T”.
See illustration.
34
Code Nº: PRM-00-0001
Revised / Date: 2006
INSTALLER’S MANUAL
Page Nº: 34 of 95
For models Nºs CG.1 4G, CG.1 3G1P and Vitroceramics:
(1) Self threading screw for kitchen cabinets with a thickness of 20 mm or 30 mm
For model NºCGC AI AL:
CGC 4G AI AL plate and Soft Series:
Fig. 4
Insert the push nuts into the screw
housings (See figure 13).
Having attached the clip which
corresponds to the thickness of the
surface (20, 30 or 40mm), fully tighten all
screws.
Key :
A–Leaktight seal B –Work surface C - Screw
D–Attachment clip E –Push nut
Step 2
After checking that the cabinet
measurements are correct, it is
necessart to attach the leaktightness
seale (J) under the hob.
Step 3
Place the clips (K) as shown in the
illustration (fig. 15) attaching them to
the gaps in the lower part of the
housing with the 4.2mm thread screws.
The clips, seal and screws are all
supplied with the appliance.
Place the attachment clips as
shown in the illustration (fig. 12)
If thickness is equal to 30mm,
use self threading screws (M5)
35
Code Nº: PRM-00-0001
Revised / Date: 2006
INSTALLER’S MANUAL
Page Nº: 35 of 95
In the 600x510 series, the procedure for fitting the plate is identical to other procedures.
Fig. 5
For the EX/70 series, the fitting process is as follows:
-{}-
-{}-
1) Turn the hob and correctly position the adhesive
side of the the seal “E”(see fig.) around the edge.
2) The ends of the seal should be joined together
without overlapping.
3) Place the hob in the space.
4) Attach with the clips “S”, carefully introducing the
tab into the slot “H”on the bottom of the hob.
5) Tighten screw “F”until it holds clip “S”to the cover
(see illustration).
This hob is designed to be recessed into
worktop surfaces with a thickness of 20, 30
or 40 mm.
Attach the leaktight seal “J”underneath the
hob.
Fix the four clips “G”using the two tabs “P”,
in the spaces “O”in the hob.
Next, place the hob in the space and tighten
the screws “T”of the 4 clips with the
corresponding key.
Este manual sirve para los siguientes modelos
14
Tabla de contenidos
Otros manuales de Quemador de Teka
Teka
Teka EM/30 2G AI Instrucciones de funcionamiento
Teka
Teka GD LUX 30 1G Manual de usuario
Teka
Teka VT TC 2P.1 Manual
Teka
Teka VT 2 1G AI AL TR CI E1 Instrucciones de instalación y funcionamiento
Teka
Teka VRTC954I Manual de usuario
Teka
Teka IZC 64630 MST Manual de usuario
Teka
Teka JZC Series Manual de usuario
Teka
Teka IRF 9480 TFT Instrucciones de funcionamiento
Teka
Teka TM 601 Manual
Teka
Teka Maestro EFX Series Manual de usuario
Teka
Teka IR 831 Instrucciones de funcionamiento
Teka
Teka EX 60.1 3G AI AL DR CI Instrucciones de instalación y funcionamiento
Teka
Teka GBC Series Manual de usuario
Teka
Teka GKST 30 12 Manual de usuario
Teka
Teka IB 6415 Instrucciones de funcionamiento
Teka
Teka GKST 90 D Manual de usuario
Teka
Teka VTN DC Manual de usuario
Teka
Teka GBC 75-G1 Manual de usuario
Teka
Teka 226317 Q21 Manual de usuario
Teka
Teka IR 321.1 Manual de usuario
