TeeJet Technologies DynaJet Flex Series Manual de usuario

DYNAJET® FLEX

INSTALLATION, SETUP AND USER GUIDE

Software version 1.02

with optional high ow option

Copyrights

reduced in any form or by any means, electronic or machine readable, recording or otherwise, without prior written consent from TeeJet Technologies.

Trademarks

Unless otherwise noted, all other brand or product names are trademarks or registered trademarks of their respective companies or organizations.

Limitation of Liability

TEEJET TECHNOLOGIES PROVIDES THIS MATERIAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED. NO COPYRIGHT LIABILITY

OR PATENT IS ASSUMED. IN NO EVENT SHALL TEEJET TECHNOLOGIES BE LIABLE FOR ANY LOSS OF BUSINESS, LOSS OF PROFIT, LOSS OF USE OR DATA,

INTERRUPTION OF BUSINESS, OR FOR INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND, EVEN IF TEEJET TECHNOLOGIES HAS

BEEN ADVISED OF SUCH DAMAGES ARISING FROM TEEJET TECHNOLOGIES SOFTWARE.

Table of Contents

DYNAJET® FLEX OVERVIEW 1

INSTALLATION 1

CONSOLE 1

INSTALLATION – STANDARD MODE 3

DynaJet® drivers .............................................................................................................................................................................................3

Power ..................................................................................................................................................................................................................3

Nozzle harnesses ............................................................................................................................................................................................3

Pressure sensor interface kit.......................................................................................................................................................................4

Boom interface module (BIM)....................................................................................................................................................................4

DynaJet® interface..........................................................................................................................................................................................4

CAN cables and terminators.......................................................................................................................................................................4

INSTALLATION – HIGH FLOW MODE 5

DynaJet® interface and drivers ..................................................................................................................................................................5

Connect terminators .....................................................................................................................................................................................5

Connect can cables to drivers....................................................................................................................................................................5

Driver battery cables .....................................................................................................................................................................................5

Boom harnesses..............................................................................................................................................................................................5

Pressure sensor................................................................................................................................................................................................5

DynaJet® 7120 console.................................................................................................................................................................................5

Other battery cable........................................................................................................................................................................................5

INITIAL STARTUP 8

Favorites.............................................................................................................................................................................................................8

Setup...................................................................................................................................................................................................................8

Units.........................................................................................................................................................................................9

Number of sections..................................................................................................................................................................9

Maximum pressure sensor value.............................................................................................................................................9

Nozzle selection ..............................................................................................................................................................................................9

Select nozzle series.........................................................................................................................................................9

Select nozzle capacity .....................................................................................................................................................9

Ready to pressure test the system......................................................................................................................................................... 10

Work screen ................................................................................................................................................................................................... 10

On screen indicators..............................................................................................................................................................10

Droplet size chart...........................................................................................................................................................10

USER SETTINGS 11

OEM settings ................................................................................................................................................................................................. 13

Enable/disable options...........................................................................................................................................................13

TUNING DYNAJET® 13

DYNAJET® NOZZLE SELECTION 14

Nozzle selection example......................................................................................................................................................................... 15

55295 E-CHEMSAVER® MAINTENANCE INSTRUCTIONS 16

General disassembly and reassembly.................................................................................................................................................. 16

APPLICATION RATES AT GIVEN SPEED 17

1www.teejet.com

DynaJet®Flex

DYNAJET® FLEX OVERVIEW

The DynaJet Flex controller works in conjunction with an existing rate controller that regulates ow via a control valve or pump regulation to

achieve a target application rate while maintaining target droplet size(s) when a speed change occurs. This system only works with automatic

rate controllers that use ow based monitoring systems and not pressure based monitoring systems. Automatic rate controllers equipped for

both ow and pressure based control should have the pressure-based system disabled to work in conjunction with DynaJet Flex.

The independent automatic rate controller loop performs the same as it would if the DynaJet controller were not present. The DynaJet Flex

controller changes ow output to each individual nozzle based upon input provided from the operator about the optimum droplet size

(pressure) for the application.

INSTALLATION

CONSOLE

The DynaJet Flex console is designed to provide years of service under typical agricultural and turf operating conditions. A tight tting

enclosure means that typical dusty environments will not cause operational problems. While occasional splashing of water will not damage

the unit, the DynaJet Flex console is not designed for direct exposure to rain. Take care not to operate the DynaJet Flex console in wet

conditions.

Figure 1: DynaJet Flex 7120 console front and back

to DynaJet interface

harness connection

Power switch

USB port

Standard RAM bracket

Bright touch screen

Safety information

TeeJet Technologies is not responsible for damage or physical harm caused by failure to adhere to the following safety

requirements.

As the operator of the vehicle, you are responsible for its safe operation.

The DynaJet Flex is not designed to replace the vehicle’s operator.

Be sure that the area around the vehicle is clear of people and obstacles before and during engagement.

The DynaJet Flex is designed to support and improve efciency while working in the eld. The driver has full responsibility for the quality and

work related results.

98-05334-EN R2

DynaJet®Flex

Figure 3: System diagram - standard mode

90-02887 - DynaJet 7120 Console w/RAM Mount Kit

Kit includes: Console and Mount

45-10148 - Sentry Interface Harness

78-05091 - Boom Interface Module (BIM)

78-05106 - DynaJet Interface

45-05963 - CAN Bulkhead Cable

45-05965 - CAN to Bulkhead Cable

DynaJet Pressure Sensor Interface Kit

Kit includes: Interface, Sensor Cable, and Pressure Sensor

90-04007: 3 m

90-04008: 10 m

78-05122 - DynaJet Driver

45-05855 - CA

N Terminator, Female (Start)

35-50048 - DynaJet Solenoid

45-05943 - Battery 60 AMP Fuse Cable

78-05121-xx - Power Distribution Module

45-05971-xx - Driver to Power Extension Cable

45-05980-xx -

Driver to Power

“Y” Cable45-05942-xx - 6 Gauge Power Extension Cable

45-10142 - BIM Harness

401-0016 - Power Cable

45-05936-xx - Tip Harness Ext

ension

45-05948-xx - Solenoid Extension Cable

45-05935-20-xx -

Tip Harness

to 12V Power

Boom Sense Wires

Sensor Cable

Pressure Sensor

to Battery Power

45-05856 - CAN Terminator, Male (End)

Console Extension Cable

45-05900: 1.5 m

45-05901: 3 m

45-05902: 6 m

45-05903: 12 m

45-058xx - CAN Extension Cable

Interface LED - Flashes until

CAN message is received,

then on steady

3www.teejet.com

DynaJet®Flex

CAN Start Terminator

(female)

at Boom Section 1

DynaJet Solenoids

to CAN connection

DynaJet Solenoids

Power Distribution Module

Nozzle Harness

DynaJet Driver

DynaJet Solenoids DynaJet Solenoids

Nozzle Harness

DynaJet Driver

DynaJet Solenoids DynaJet Solenoids

Nozzle Harness

DynaJet Driver

DynaJet Solenoids DynaJet Solenoids

Nozzle Harness

DynaJet Driver

INSTALLATION – STANDARD MODE

DynaJet® drivers

There will be one DynaJet driver 78-05122 per boom section with a

limit of 20 nozzles per section.

• Mount them so they are at the end of each section that is

closest to the middle of the boom.

Power

Power will be sourced from the battery using the 60 amp fused cable

45-05943.

Power from the battery will be routed to the boom using the 6 gauge

power cables 45-05942-xx

The power distribution modules 78-05121-xx will connect to the

45-05942-xx cables.

Power will then route from 78-05121-xx to each DynaJet driver

78-05122 using cables 45-05971-xx.

Figure 2: Installation diagram - standard mode

Nozzle harnesses

When installing nozzle harnesses 45-05935-xx-xx always start with

section 1 and continue to the last section.

Each section will require nozzle harnesses designed for your specic

nozzle spacing and number of nozzles.

• Nozzle harnesses are built with an even number of outputs.

• Some sections will use more than one harness to equal the

number of nozzles in that section.

The yellow and white solenoid cables on the nozzle harnesses must

alternate across the entire boom. When sections have odd numbers

of nozzles then accounting for the altering can be accomplished

one of two ways:

A. By crossing the two solenoid cables

B. By installing nozzle harness reversing adapters 45-05952

98-05334-EN R2

DynaJet®Flex

CAN Start Terminator

(female)

at Boom Section 1

DynaJet Solenoids

to CAN connection

DynaJet Solenoids

Power Distribution Module

Nozzle Harness

DynaJet Driver

DynaJet Solenoids DynaJet Solenoids

Nozzle Harness

DynaJet Driver

DynaJet Solenoids DynaJet Solenoids

Nozzle Harness

DynaJet Driver

DynaJet Solenoids DynaJet Solenoids

Nozzle Harness

DynaJet Driver

Pressure sensor interface kit

The DynaJet system requires pressure sensor interface kit 90-04007

or 98-04008 to be installed.

• The pressure sensor interface kit should be mounted close to

the boom manifold.

Boom interface module (BIM)

The boom interface module (BIM) 78-05091 is used by the DynaJet

system for boom sense.

The BIM harness connects between the BIM and the can.

On the BIM harness 45-10142, the boom sense wires (or ying

leads) are supplied to tie into existing machine boom section

12V on/0V off outputs.

If not using 45-10142, some machine specic harnesses are

available.

The BIM can be mounted in the cab or outside depending upon your

installation.

DynaJet® interface

The DynaJet interface 78-05106 connects to the Sentry interface

harness 45-10148:

The Sentry interface harness connects to

A. The console 75-30119 (extension cable may be used)

B. Power 12V for powering the CAN

C. CAN

The DynaJet interface can be mounted in the cab or outside

depending upon your installation.

CAN cables and terminators

The start terminator 45-05855 must be connected to the DynaJet

driver 78-05122 for section 1.

Can cables must be connected in series:

A. To each DynaJet driver 78-05122

B. To the boom interface module 78-05091 (via BIM harness

45-10142)

C. To the DynaJet interface 78-05106 (via sentry interface

harness 45-10148)

D. To the pressure sensor interface kit (via pressure interface

78-05110)

The end terminator 45-05856 must be connected to the driver

module 78-05122 for the last section.

5www.teejet.com

DynaJet®Flex

INSTALLATION – HIGH FLOW MODE

The following illustration and steps are only a guideline of an installation based on a specic vehicle conguration. Installations on

other vehicles may vary. If there are questions concerning the installation of the DynaJet Flex system on this vehicle, or due to the

changes in component specications the parts supplied in the kit are not exactly as presented in this document, please contact

your dealer or TeeJet customer service representative for clarication before installation. TeeJet technologies is not responsible for misuse or

incorrect installation of the system.

DynaJet® interface and drivers

Step 1a – mount the (F) DynaJet HF drivers 78-05124 onto brackets, one for each boom section.

Step 1b – mount the (D) DynaJet HF interface 78-05123, connecting to the (C) DynaJet interface harness 45-10177, and (H) boom harness

45-10178.

Connect terminators

Step 2a – connect the (I) start terminator 45-05855 to (K) 4 nozzle harness (1-4) 45-10174, rst section.

Step 2b – connect the (J) end terminator 45-05856 to (M) 4 nozzle harness (9-12) 45-10176, last section.

Nozzle harnesses

Step 3 – install nozzle harness (K) 4 nozzle harness (1-4) 45-10174, (L) 4 nozzle harness (5-8) 45-10175, and (M) 4 nozzle harness (9-12)

45-10176. Each harness features two solenoid connections per nozzle body, supporting (4) nozzle bodies in total.

Note: specific section breakdown may vary by installation

Connect can cables to drivers

Step 4 – using the (E) can extension cables, connect the (I) DynaJet HF drivers 45-05124 to the (D) DynaJet HF interface 78-05123.

Driver battery cables

Step 5 – connect the battery cable 45-05987 to the three (3) (F) DynaJet HF drivers 78-05124, and to the battery.

Boom harnesses

Step 6 – install the (H) boom harnesses 45-10178, 45-10179, or 45-10181 connecting to the (D) DynaJet HF interface 78-05123.

Pressure sensor

Step 7 – connect the boom pressure sensor 0-10 bar to the (C) DynaJet HF interface harness 45-10177. The pressure sensor interface kit

should be mounted close to the boom manifold

DynaJet® 7120 console

Step 8 – connect the (A) DynaJet 7120 console 90-02887 to the (C) DynaJet HF interface harness 45-10177 via console extension cables.

Other battery cable

Step 9 – connect 401-0012 to the battery and route leads as needed.

98-05334-EN R2

DynaJet®Flex

Figure 4: System diagram - high flow mode

(H) Boom Harness

45-10178 to IC18

45-10179 to Raven 440

45-10181 to Raven Envizio

(F)

78-05124

DynaJet HF Driver

(D) 78-05123

DynaJet HF Interface

DynaJet Interface Harness

(M) 45-10176

4 Nozzle Harness 9-12

(L) 45-10175

4 Nozzle Harness 5-8

(K) 45-10174

4 Nozzle Harness 1-4

(A) 90-02887 - DynaJet 7120 Console w/RAM Mount Kit

Kit includes: Console and Mount

Sensor Cable

Pressure Sensor

(I)

45-05855

CAN Terminator,

Female (Start)

to Battery Power

to Battery Power to Battery

(J) 45-05856

CAN Term

inator,

Male (End)

(B) Console Extension Cables

45-05900: 1.5 m

45-05901: 3 m

45-05902: 6 m

45-05903: 12 m

(E) 45-058xx

CAN Extension Cable

(G) DynaJet Pressure Sensor Interface Kit

Kit includes: Sensor Cable and Pressure Sensor

90-04007: 3 m

90-04008: 10 m

7www.teejet.com

DynaJet®Flex

Item Part # Description Illustration

A90-02887 DynaJet 7120 console

B45-05900: 1.5 m

45-05901: 3 m

45-05902: 6 m

45-05903: 12 m

Console extension cable

C45-10177 DynaJet interface harness

D78-05123 DynaJet HF interface

E45-05857: 1 m

45-05858: 2 m

45-05859: 4 m

45-05864: 10.5 m

CAN extension cable

F78-05124 DynaJet HF driver

G90-04007: 3 m

90-04008: 10 m

DynaJet pressure sensor interface kit

H45-10178 to IC18

45-10179 to Raven 440

45-10181 to Raven Envizio

Boom harness

I45-05855 CAN terminator, female (start)

J45-05856 CAN terminator, male (end)

K45-10174 4 Nozzle harness 1-4

L45-10175 4 Nozzle harness 5-8

M45-10176 4 Nozzle harness 9-12

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de control de TeeJet Technologies

TeeJet Technologies

TeeJet Technologies Dynajet FLEX 7140 Manual de usuario

Manuales populares de Sistema de control de otras marcas

Pentair Pool Products

Pentair Pool Products Compool Manual de usuario

ComfortNET

ComfortNET CTK04 Manual de usuario

Fireye

Fireye InSight II 95DSS3 Manual de usuario

CAME

CAME G3000 Manual de usuario

Idemia

Idemia MorphoAccess VP MD Manual de usuario

Axis

Axis P1445-LE-3 Manual de usuario

HEIDENHAIN

HEIDENHAIN TNC 150 B Manual de usuario

CNC-Step

CNC-Step High-Z T-Series Manual de usuario

Doosan

Doosan DVF Series Manual de usuario

Honeywell

Honeywell KAP 140 Manual de usuario

Honeywell

Honeywell vk41 series Manual de usuario

AirBench

AirBench FPW Guía de instalación

Cypress

Cypress HHR-3160 Manual de usuario

CAME

CAME GLT40AOS Manual de usuario

Zonex

Zonex GEN II -VVT Guía del usuario

Altronics

Altronics K 9650 Manual de usuario

micro-trak

micro-trak RoadMaster Manual de usuario

micro-trak

micro-trak Calc-An-Acre II Manual de usuario