TeeJet Technologies RXA-52 Manual de usuario

USER GUIDE

98-01569-EN-R1_A4LT-RXA52-UG.docx

RXA-52

MULTI-FREQUENCY, MULTI-CONSTELLATION, GNSS ANTENNA

Thank you for choosing TeeJet Technologies’ RXA-52 as your

GNSS antenna solution. This document provides instructions for

mounting and operation of the RXA-52. Contact a local dealer for

more information or visit www.teejet.com.

The RXA-52 is an active antenna designed to receive signals

from GPS, GLONASS, BeiDou and Galileo satellites as well as L-

Band signals.

The RXA-52 antenna is designed to operate in GPS L1/L2,

GLONASS L1/L2 and L-Band frequencies. The RXA-52 also

supports the Galileo E1 and E5b frequencies as well as BeiDou

B1 and B2 frequencies.

It can be used with any console with an internal GNSS receiver or

any device with an antenna input port that both receives the RF

signal and provides 3.3 - 18.0 VDC to the antenna

RXA-52 Kit Includes

•RXA-52 Antenna

•Coaxial Cable, SMA male to TNC male, 20′/6 m (part number 45-05957) or 30′/9 m (part number 45-05620)

•Mounting Plate (part number 65-05243)

INSTALLATION

Site Selection Guidelines

Before installing the antenna, select a site that as closely as possible meets the following conditions for optimal performance:

•An unobstructed line-of-sight from horizon to horizon and at all bearings and elevation angles

•As far as possible from reflective objects, especially those that are above the antenna and any water bodies, which can be a strong

source of multipathreflections

•If obstructions and reflective surfaces are within 100 feet / 30 meters, ensure the site is as high as possible. Otherwise, mount the

antenna as close as possible to a reference ground plane, i.e., rooftop, earth, etc., if one exists.

•When mounting the RXA-52 Antenna, a space of at least 5.9 inch / 15 cm between the antenna and any bend in the cable is

required. Any length shorter than 5.9 inch / 15 cm puts undue stress on the cable and the enclosure for the RXA-52.

•The antenna should not be mounted where water can pool around it. The antenna housing is designed to withstand rain and

splashing, but not submersion in liquids for sustained periods of time.

•Mount the antenna above all other metal objects to avoid multipath. Satellite signals received by the GNSS antenna by a reflection

from an object can decrease positioning accuracy. For example, roof racks, large headlight enclosures, etc., can cause multipath

that may result in a jump in GNSS position.

Warning! To avoid potential adverse effects, do not locate antennas near any high sources of heat.

USER GUIDE TEEJET TECHNOLOGIES

98-01569-EN-R1_A4LT-RXA52-UG.docx

Installing the Antenna

After a site has been selected, install the antenna as follows:

1. Mount the antenna on a secure, stable structure using the provided magnetic mounts. A surface mounting plate (Part Number

65-05243) is also available for mounting on non-magnetic surfaces. See Mounting Plate Instructions for details.

2. Attach the TNC connector of the coaxial cable to the antenna’s TNC connector. Attach the other end of the coaxial cable to the

antenna input port of the receiving device, which must provide power as detailed in the “Specifications” section of this guide. All

TeeJet Technologies GNSS receivers provide the necessary power through their antenna RFconnectors.

Figure 1: Orientation Example

Orient antenna towards the front of the vehicle.

Route cable toward the back of vehicle.

Figure 2: RXA-52 Dimensions in Millimeters

Front

Back

Mounting

Magnet

× 2

4 × 0.7 Threaded

Insert

× 2

TNC Connector

USER GUIDE TEEJET TECHNOLOGIES

98-01569-EN-R1_A4LT-RXA52-UG.docx

Mounting Plate Instructions

The RXA-52 is equipped with two (2) built-in magnets for attaching to the included mounting bracket. If a permanent mount for the

RXA-52 is required, please contact TeeJet Technologies Technical Support for more information.

Intermediate Mounting Plate Template

A template for the intermediate mounting plate has been provided below.

•Red circles indicate holes where attachment will occur.

•Green lines indicate the outline of the mount and other holes for attaching the release plate.

WARNING! The optimal screw penetration into the mounting holes is 0.25 inch / 6 mm (±1/32 inch / 1 mm) deep. When selecting

screws for mounting, ensure the screw penetration does not exceed this specification. Using excessively long screws can

damage the antenna enclosure.

Antenna Care

•The RXA-52 is designed to withstand the elements, including rain, snow, and dust.

•However, to ensure your antenna performs optimally, keep the radome (the top surface of the antenna) clean and brush off any ice

and snow.

6.25 inch

158.75 mm

5.0 inch

127.0 mm

0.50 in

ch × 4

12.7 mm × 4

0.50 in

ch × 4

12.7 mm × 4

Ø0.27 inch ± 0.01 inch

drill thru × 4

Ø6.858 mm ± 0.01 mm drill thru × 4

This side will route

oward back of vehicle

USER GUIDE TEEJET TECHNOLOGIES

98-01569-EN-R1_A4LT-RXA52-UG.docx

SPECIFICATIONS

Performance

Signal Received

GPS ...............................................................................L1, L2

GLONASS ......................................................................L1, L2

Galileo ......................................................................... E1, E5b

BeiDou ..........................................................................B1, B2

L-Band

Pass Band (typical)

Upper passband ....................................... 1588.0 ± 23.0 MHz

Lower passband ....................................... 1220.0 ± 31.0 MHz

L-Band ......................................................1555.0 ± 10.0 MHz

Out-of-Band Rejection

Band edges ± 50 MHz ......................................15 dB (typical)

Band edges ± 100 MHz ....................................25 dB (typical)

LNA Gain (typical)

L1 ................................................................................... 34 dB

L2 ................................................................................... 38 dB

Gain at Zenith (90°)

L1/B1/E1/G1 ............................................. +4.0 dBic minimum

L2/B2/E5b/G2 ........................................... +4.0 dBic minimum

L-Band ...................................................... +4.0 dBic minimum

Gain Roll-Off (from Zenith to Horizon)

L1/B1/E1/G1 .................................................................. 12 dB

L2/B2/E5b/G2 ................................................................ 12 dB

L-Band ........................................................................... 12 dB

Phase Center Stability

....................................................................................<5.0 mm

Polarization

....................................................................Right-hand circular

Noise Figure

..........................................................................2.5 dB (typical)

VSWR

..................................................................................... ≤2.0 : 1

L1-L2 Differential Propagation Delay

........................................................................7 ns (maximum)

Group Delay Ripple

.......................................................................................<15 ns

Nominal Impedance

.......................................................................................... 50 Ω

Physical and Electrical

Dimensions

................................................ 6.1 in W × 1.77 in H × 6.85 in L

...........................................155 mm W × 45 mm H ×174 mm L

Weight

........................................................................ 15.88 oz / 450 g

Mounting

................................................................ 2 × magnetic mounts

.................................................................2 × M4 screw inserts

Power

Input voltage .............................................. +3.3 to +18.0 VDC

Current .............................................................20 mA (typical)

Environmental

Temperature

Operating ...........................-40°F to +185°F / -40°C to +85°C

Storage ..............................-67°F to +185°F / -55°C to +85°C

Humidity

................................................................ 95% non-condensing

Salt Fog

....................................................MIL-STD-810G (CH1), 509.6

Water/Dust Resistance

...............................................................................IP67, IP69K

Vibration (operating)

Random ............MIL-STD-810G (CH1), 514.7 (15 g) Annex E

Procedure 1, Category 24

Shock

.....................MIL-STD-810G (CH1), 516.7 (40 g) Procedure 1

Bump

.........................................................IEC 60068-2-27 Ea (25 g)

Compliance

......................................................................... FCC, CE, ISED

RoHS ...................................................EU Directive 2011/65/EU

Warranty

1 year from date of purchase.

English-International www.teejet.com

Otros manuales de Antena de TeeJet Technologies

TeeJet Technologies

TeeJet Technologies RX610 Manual de usuario

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario