TECO TWM50FA Manual de usuario
5Kg FRONT LOAD
CLOTHES WASHER
USER’S MANUAL
Model : TWM50FA
Engineered To Perform
To ensure proper use and your safety, please read the following user manual completely before operating this
appliance. Please keep this manual in a safe place for future reference.
1
Thank you for purchasing our product and thank you for placing your confidence in us.
Read this manual carefully before use. Follow instructions and keep the manual for future reference.
Follow the operating instructions and safety notices in this manual.
If any trouble arise, do not fix it yourself or hand it to the after sales service centre which have not
been authorised. Please contact TECO service on 1300 660 037 (9am ~ 4pmAEST Mon - Fri).
WARNING ICON
This symbol indicates information concerning your personal safety
CAUTION ICON
This symbol indicates information on how to avoid damaging the appliance
SAFETY PRECAUTIONS
Keep ventilation openings, in the appliance enclosure or in the built in structure, clear of obstruction.
This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety.
Young children should be supervised to ensure that they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
When disposing of the appliance, do so only at an authorised waste disposal centre.
Don’t store inflammable materials such as ether, benzene, LP gas and glue etc near the appliance.
Please keep the appliance away from substances which could cause ignition.
Before obtaining access to electrical terminals, all electrical supply circuits must be disconnected.
The washer is designed to operate on a single phase power supply within a voltage range of
220~240V/50Hz.
Don’t splash water on the rear of the appliance, for it may cause malfunction or electric shock.
Before cleaning the appliance, always switch off the appliance and unplug it, or pull the house fuse or
switch off the circuit breaker.
Never disassemble any part of the clothes washer.
Never insert your hand and remove items from the washer until the appliance has come to a complete
stop.
Choose a location that is indoors, completely dry and away from damp environments.
Never splash, wet or hose the appliance. It is recommended to use a damp cloth when cleaning the
cabinet.
Do not attempt to wash fabrics that contain latex or rubber material.
Do not place items that have come in contact with any flammable materials such as petrol/gasoline,
kerosene, cleaning solvents, vegetable oil, cooking oil or any explosive substances.
Never place heat sources (candle, heater, etc.) on top of or near the washer.
Never pull the power cord from the socket by the cord. Always unplug the washer using the plug.
Safety of children
Packaging (e.g. wraps, polystyrene, etc.) can be dangerous for children. There is a risk of suffocation.
Keep packaging materials away from children. Remember to dispose of old appliances in accordance
with local laws. Pull out the mains plug, cut off the mains cable, break or remove spring or bolt catches
if fixed and ensure that children cannot lock themselves in the appliance when playing (there is risk of
suffocation) or involve themselves in other dangers, for children cannot recognize the hazard present
in household appliances themselves. Therefore, it is very important for parents to make adequate
supervision and never let children play with the appliance.
WARNING
CAUTION
2
TABLE OF CONTENTS
Safety Precautions
Table Of Contents
Identifying Washer Parts
Quick Start Guide
Installation
Pre Wash Checklist
Control Panel
Wash Programs & Functions
Loading Detergent
Wash Program Information
Cleaning & Maintenance
Troubleshooting
Repairs, Service & Warranty
Specifications
1
2
3
4
5 - 6
7 - 8
9
10
10
11
12
13 - 14
15
16
................
................
................
................
................
................
................
................
................
................
................
................
................
3
IDENTIFYING WASHER PARTS
Detergent Dispenser
Detergent Dispenser
Control Panel
START/PAUSE Button
Drum
Cabinet
Power Button
Door
Service Panel
Adjustable Feet (x4)
Shipping Bolt
Caps x4
Cold Water
Inlet Hose x1 Drain Hose
Support x1
Program Selection Dial
4
1. Install the clothes
washer
2. Load the laundry
3. Add washing
detergent
4. Close the door
5. Attach/check the
drain pipe
6. Turn on the water tap
7. Connect the power plug
Press the power button
8. Select a wash
program
9. Press the
START/PAUSE button
QUICK START GUIDE
Wash Program Selection
1. Press the POWER button
2. Select a program
3. Select a water level or other functions
4. Press the START/PAUSE button
When the program finishes
When the wash program finishes, the buzzer will sound and the power will
be automatically switched off. At this point, turn off the water supply to the
washer. It is recommended to remove the power plug from the mains power
source for safety.
5
INSTALLATION
Unpacking Instructions
1. Remove the clothes washer from the carton.
NOTE: Please dispose of packaging and
plastic bags responsibly.
2. Open the washer door and remove the
accessories from inside the washer.
3. Remove the four shipping bolts from the rear
of the washer prior to use.
4. Plug the shipping bolt holes with the supplied caps.
Choosing a location
The clothes washer should be located on a firm and flat
surface. An uneven surface may cause excess operating
noise or vibration and effect the performance of the
washer.
The noise may be increased if the floor is
not firm.
It is not recommended to place on carpet
flooring. If this can not be avoided, place a
solid sheet under the appliance.
Choose a location which is indoor, dry, not exposed to direct sunlight, high
temperature or humidity.
It is recommended a clearance of at least 300mm away from objects and walls
on both sides and top. Ensure the clearance behind the appliance is not less
than 100mm and at least 160° clearance for the door to swing open.
Levelling the Washer (Adjustable feet)
For optimal washing performance, reduced noise and to
minimise vibration, it is important to ensure the washer is
completely flat and level before use. Using a spirit level,
check both horizontal and vertical stability.
To adjust the feet:
1. Loosen the lock nut (A).
2. Adjust each foot (B). Turn left to raise or right to lower
as necessary.
3. Once all four feet have been adjusted and the washer
is completely level, tighten the lock nut (A).
A
B
Install supplied caps
to cover holes from
shipping bolts.
6
Installing the Drain Hose
When placing the drain hose, ensure it is above 600mm and below 1000mm.
Otherwise, the washer may not drain correctly and an error will occur. Ensure
the drain hose is placed in a drain with a diameter of at least 30mm to meet
minimum drainage flow requirements. Secure the drain hose in place to avoid
leaking and spilling as the water drains. Do not immerse the drain hose in
water.
Installing the water inlet hose
1. Fasten one end of the inlet hose to
the tap. Ensure there is a rubber
washer inside the hose before
fastening. The washer prevents water
leakage.
2. Securely tighten the other end of the inlet hose to the clothes washer inlet
valve. Ensure the rubber washer is inside the hose before tightening.
3. When tightening the clamping nut, apply even pressure. Do not apply too
much force or twist the valve as this may damage or break the valve joint.
PLEASE NOTE
Be sure to install the inlet hose to COLD water only. Incorrect installation can
reduce performance or damage the clothes washer.
Sink / Basin
Secure in
place here
Drain at least 30mm
diameter
Bind
Max.1000
Min.600mm
Min.600mm
Max.1000mm
mm
7
PRE WASH CHECKLIST
Before starting each wash, please check the following:
Level the clothes washer by adjusting the feet.
Install the water inlet hose
Connect to a power source
Adjust the feet by turning clockwise
to extend or anti clockwise to
shorten.
Slightly tilt the clothes washer back
to access the adjustable feet.
Ensure all four corners are flat and
level to the surface it is placed on.
Ensure the clothes washer is
level and stable prior to starting
each wash. An unstable clothes
washer can cause the drum to
shake during a wash and knock the
cabinet.
Ensure the inlet hose has been
correctly installed and is securely
fastened to the water mains and
the inlet valve at the rear of the
clothes washer.
Ensure the inlet hose has been
attached to a COLD water tap only.
NOTE: Ensure your hands are
completely dry before touching the
mains outlet, any electrical plugs or
cables.
Ensure the clothes washer is securely plugged
into the mains power supply and it is switched to
the ON position.
Adjustable feet
CAUTION
8
Open the mains water supply
Position the drain hose
Insert laundry and washing powder
Before each wash, be sure to check all pockets
and remove contents (keys, coins, etc.) and
close any zippers to prevent damage to the
clothing and the clothes washer.
PRE WASH CHECKLIST
Ensure the water mains are in the open position and a
steady water supply is available to the clothes washer.
Ensure the drain hose is correctly mounted
between 600 and 1000mm above the ground.
The drain water may overflow if the drain hose
is below 600mm or decrease flow if placed
above 1000mm.
Do not overload the clothes washer, this will effect the performance of the
clothes washer. Follow the instructions on the washing powder packaging to
determine the correct dose of powder for the laundry to be washed.
CAUTION
mm00
6mu
miniM
00mm0
1mumixa
M
9
CONTROL PANEL
400
800
NoSpin 20
1200
5.0
Spin Speed Button
Press this button to select the
spin speed. Change the spin
speed by pressing this button
repeatedly. Choose between No
Spin, 400, 800 and 1200 RPM.
Start/Pause Button
Press this button once a wash program
has been selected to start the program.
Once a wash has begun, press this
button to pause the program. Press
Start/Pause again to resume.
Program Dial
Turn this dial to select a wash
program. Choose between
Cotton, Synthetic, Wool,
Underwear, Cotton Intensive, Spin
and Drum Clean.
Temp. Button
Press this button to select the
water temperature used during
a wash. Select between 20,
40, 60 and 90oC. NOTE: When
the Temp. light is off, the water
temperature will be cold.
Power Button
Press this button to
switch the washer
on and off. Press
once to switch on.
When finished a wash
program, press to
switch off.
Tabla de contenidos
Otros manuales de Arandela de TECO
