Tecnoware ERA PLUS 900 Manual de usuario

Uninterruptible Power Supply

ERA PLUS 900

ERA PLUS 1.100

User’s manual

UPS ERA PLUS 900-1.100 1 User’s manual

Index

Sa ety Warnings ................................................................................ 2

1 Introduction ................................................................................. 3

2 General Characteristics ................................................................... 4

3 Receipt and site selection ................................................................ 4

4 EXTERNAL DESCRIPTION .................................................................. 5

4.1 Front Panel ............................................................................. 5

4.2 Rear Side ................................................................................ 6

5 Electrical Installation and First Start Up ............................................... 6

6 Functioning ................................................................................. 8

6.1 ormal Mode ........................................................................... 8

6.2 Battery Mode ........................................................................... 8

6.3 Low Battery and Automatic Restart ................................................. 8

6.4 Load Control ............................................................................ 9

6.5 Fault Condition ........................................................................ 9

7 Communication Inter ace ................................................................. 9

8 Technical Characteristics ................................................................. 9

9 Maintenance ............................................................................... 11

9.1 UPS Cleaning ......................................................................... 11

9.2 Battery ................................................................................ 11

9.3 Battery Replacement ............................................................... 11

9.4 Operator Safety ...................................................................... 12

10 Troubleshooting ........................................................................... 12

Con ormity to the European Directives ................................................... 14

Product Disposal ............................................................................... 14

Lead Batteries ................................................................................. 14

All trademarks are property of their respective owners.

TEC OWARE s.r.l.

Via Montetrini, 2E – Loc. Molino del Piano – 50065- Pontassieve (FI) – Italy

www.tecnoware.com

Edition: April 2015 – version: 1.0

o part of this manual may be reproduced, even partially, without the

authorisation of TEC OWARE s.r.l.

TEC OWARE s.r.l. reserves the right to change specifications at any time

and without notice.

User’s manual 2 UPS ERA PLUS 900-1.100

Sa ety Warnings

Read this manual care ully and completely be ore installing and using the TECNOWARE ERA

PLUS Uninterruptible Power Supply, which, rom here a ter, will also be re erred to as UPS.

This manual should be kept close to the UPS and read be ore the UPS is installed and used.

The UPS must be used only by properly trained personnel. To ensure correct and sa e

operations, it is necessary that operators and maintenance personnel observe the general

sa ety Standards as well as the speci ic instructions included in this manual.

Risk o electric shock: do not remove the cover. The UPS contains internal parts, which are at a

high Voltage and are potentially dangerous, capable o causing injury or death by electric

shock.

There are no internal parts in the UPS, which are user serviceable. Any repair or maintenance

work must be per ormed exclusively by quali ied technical personnel authorized by

TECNOWARE. TECNOWARE declines any responsibility i this warning is disregarded.

Warning to the technical personnel authorized or Service: since internal components are

connected to the batteries, they will remain powered, and there ore dangerous, even a ter the

UPS has been disconnected rom AC power mains. Be ore any repair or maintenance work,

disconnect the batteries, by removing the positive cable (red colour) rom the positive pole o

the battery.

It is compulsory to ground the UPS according to Sa ety Standards. The AC mains power supply

socket used to power the UPS must have an earth connection.

In the event o AC main power supply ailure (when the UPS works in Battery mode), do not

unplug the power supply cable to the UPS to ensure earth continuity to the connected loads.

Since the AC mains power supply cable acts as a separation device, the AC mains power socket

used to supply the UPS and/or the rear side o the UPS must be accessible to easily disconnect

the cable in case o dangerous conditions.

Risk o electric shock at the Output lines when the UPS is ON.

Risk o electric shock at the Output lines while the unit is connected to the AC utility line.

Do not obstruct ventilation slots or holes and do not rest any object on top o the UPS.

Do not insert objects or pour liquids in the ventilation holes.

Install the UPS indoors, in a protected, clean and moisture- ree environment.

Do not expose to the direct sun light.

Do not keep liquids, lammable gases or corrosive substances near the UPS.

UPS ERA PLUS 900-1.100 3 User’s manual

1Introduction

ERA PLUS is a Line Interactive UPS (Uninterruptible Power Supply) specifically designed to protect your computer

from any type of irregularities in the AC line (such as black-outs, under or over voltages, micro-interruptions),

which often cause damage to your Hardware and Software.

Under normal AC line condition, ERA PLUS performs output voltage regulation and filters frequently occurring

electrical disturbances (such as transients, spikes, interferences, etc.), thus protecting all devices connected to

the outlets, and recharging the batteries in an ideal way. In case of anomaly to the AC line, the UPS continues

feeding the protected equipment.

ERA PLUS is equipped with an USB interface which can be used to notify a power failure or a low battery condition

directly to a computer: this makes it possible to automatically save your data during an extended black-out with

the most widespread operating systems (Windows, Mac OS X, Linux, etc.).

Read this manual care ully be ore using the ERA PLUS; it includes important sa ety

warnings and use ul advices or correct use and installation.

This manual is a guide that enables you to correctly install and use your ERA PLUS. This

manual includes important SAFETY instructions or the operator, or the UPS correct

installation, and gives use ul advice on the product and battery maintenance. For any

type o problem, please re er to this manual be ore calling the customer service.

ERA PLUS is constantly being developed and improved: consequently, your unit may differ somewhat from the

description contained in this manual.

This manual includes the following models:

•ERA PLUS 900 (900 VA)

•ERA PLUS 1.100 (1.100 VA)

In this manual ERA PLUS will simply be referred to as UPS.

User’s manual 4 UPS ERA PLUS 900-1.100

2General Characteristics

ERA PLUS has all the advanced features, which guarantee maximum reliability and safety:

•All functions are controlled by a microprocessor, giving full guarantee of high reliability.

•Output Voltage regulation through AVR (Automatic Voltage Regulation).

•Overload protection both in normal mode and in battery mode.

•High performance battery charger, which extends the battery medium life ensuring an optimal recharge.

•Start up even if the electrical network is not available.

•Automatic restart after an automatic shut down due to a low battery condition once the AC utility power

returns.

•Adapts automatically to 50 or 60 Hz input frequency.

•Acoustic signals of various kinds indicating functioning modes and alarm/fault condition.

•Communication with the computer through USB interface.

•High efficiency

•Maximum reliability

•Smart design and easy to use

3Receipt and site selection

Carefully remove the UPS from its packaging, and carry out a meticulous inspection. We recommend keeping the

original packaging in a secure place, in case you need to send the UPS for maintenance purposes. In case of

transport damage, notify the carrier and dealer immediately.

We recommend paying attention to the below points in order to choose a correct placement for your UPS:

•The UPS is designed to operate in a protected environment (e.g. offices). We therefore recommend

installing it in a place with very little or no humidity, dust or smoke.

•In all circumstances, see the “Technical Characteristics” chapter for environmental specifications and

check that the selected area meets these specifications.

•During normal operation the UPS discharges a minimal amount of heat. So it is necessary to leave at least

20 cm of unobstructed space all around the UPS in order to keep it properly ventilated.

•Do not obstruct ventilation holes.

•Do not insert objects or pour liquids in the ventilation holes.

•Do not rest any object on top of the UPS.

•Do not keep liquids, flammable gases or corrosive substances near the unit.

•Install the UPS on a properly tiled floor. Avoid the installation on a floor that is not tiled flat.

UPS ERA PLUS 900-1.100 5 User’s manual

4EXTERNAL DESCRIPTION

4.1 Front Panel

The front panel informs the user about operating status, alarm conditions and measurements. Front panel shown

below consists of two parts:

1. The ON/OFF button: enables the user to turn O /OFF the UPS.

2. The LINE/BATTERY led: this led (blue color) is always on during the functioning in ormal Mode, it flashes

one time every 4 seconds in Battery mode and it flashes one time every second in Low Battery condition.

Figure 1 – Front panel

User’s manual 6 UPS ERA PLUS 900-1.100

4.2 Rear Side

Figure 2 – Rear Side

1. AC Input cable: to connect the UPS to the AC utility line.

2. Input use: electrical specification: max current 5 A, voltage 250 V.

3. Grounded UPS Output receptacles: Schuko/Italian type, black colour, to supply critical loads.

4. Computer Inter ace (USB connector): it is the communication USB port. (Only for UPS ERA Plus 1.100)

In case o anomaly to the AC line (black-out), the UPS Output receptacles (black colour,

#3) continue supplying the correct power to all connected equipment.

5Electrical Installation and First Start Up

UPS ERA PLUS 900-1.100 7 User’s manual

We advise you to follow the steps below explained for greater safety:

1. Switch off all the devices (Personal Computer or other electronic devices) that need to be supplied by the

UPS.

2. Connect the UPS Input socket to the AC line outlet. It is mandatory to ground the AC line outlet according

to the Sa ety Standards. Carefully check the grounding, make sure that the utility power is available, and

that its range falls within the UPS specifications (refer to the “Specifications” chapter).

3. Press the ON/OFF button on the front panel: the UPS emits a brief acoustic signal, turns the led display on,

and performs a unctioning SELF-TEST. After some seconds the UPS starts to work in Normal mode. Leave

the UPS in ormal mode for at least 4 hours in order to completely recharge the batteries.

4. Switch the UPS off (by pressing again the O /OFF button).

5. Connect the devices to be supplied to the UPS outputs. Be sure all the devices have the main switch in O

position.

6. Turn on the UPS again. Check that it starts working correctly and it doesn’t signal any sort of anomaly.

Moreover be sure that all the devices connected to the UPS outputs are working correctly.

7. Simulate a black-out by removing the AC Input line. The UPS starts working in Battery mode: the UPS emits a

brief acoustic signal every 10 seconds.

8. Be sure that all the devices connected to the UPS outputs are working correctly and the UPS doesn’t signal

any sort of anomaly.

9. Restore the AC Input line: after few seconds the UPS turns back in ormal mode.

Before using ERA PLUS normally, leave it in ormal mode in order to charge the batteries completely as specified

at point 3. The batteries reach the 90% of their capacity after about 4 hours of recharge.

It is compulsory to ground/earth the UPS according to the Sa ety Standards.

Risk o electric shock at the Output lines i the UPS is ON, even when the UPS is not

connected to AC utility line.

Risk o electric shock at the Output lines while the unit is connected to the AC utility

line.

Risk o electric shock: do not remove the cover. The UPS contains internal parts, which

are at a high Voltage and are potentially dangerous, capable o causing injury or death

by electric shock.

There are no internal parts in the UPS that are user serviceable. Any repair or

maintenance work must be per ormed exclusively by quali ied technical personnel

authorized by TECNOWARE. TECNOWARE declines any responsibility i this warning is

disregarded.

Disregard or these warnings may lead to a risk o electric shock to operators.

User’s manual 8 UPS ERA PLUS 900-1.100

6Functioning

6.1 Normal Mode

The UPS typically works in Normal mode: Input mains power is available and its amplitude is within specifications.

In ormal mode the LINE/BATTERY led is always on.

During ormal mode, the UPS recharges the batteries and keeps them in an optimal charging voltage.

6.2 Battery Mode

The UPS automatically runs in Battery mode if the AC Input Line voltage amplitude gets out of security limits (in

case of a black-out or over-voltage/low-voltage): in this case, the UPS supplies the required output power by its

internal battery and by the Inverter block.

The UPS automatically returns in ormal mode a few seconds after the AC Input Line is recovered.

In Battery mode the UPS emits an acoustic alarm signal every 10 seconds and simultaneously the LINE/BATTERY

led flashes.

6.3 Low Battery and Automatic Restart

In Battery mode, ERA PLUS indicates the Low Battery condition whenever the battery reaches a charge level

allowing connected devices to operate for approximately one more minute.

During Low Battery condition the UPS emits an acoustic alarm signal every second and simultaneously the

LINE/BATTERY led flashes.

If AC Input does not come back on within few minutes, the UPS shuts-down automatically thus preventing the

batteries from discharging excessively; the UPS stops supplying Output power, deactivates control panel indication

and goes to a waiting state. Once AC Input comes back on, the UPS restarts automatically and after some seconds

it goes back to work in ormal mode.

After a complete discharge, the UPS needs 4 hours to recharge completely the batteries. The UPS recharges

batteries automatically if it works in ormal mode or if it is off and connected to the AC Input Line.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unión Postal Universal de Tecnoware

Tecnoware

Tecnoware EVO DSP PLUS 1.200 Rack Tower PF 0.9 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 1.0 - pf 0,9 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS 800 PF 0.9 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS TM 10 KVA Manual de usuario

Tecnoware

Tecnoware EVO 3.0 RT Manual de usuario

Tecnoware

Tecnoware EVO 3.0 Manual de usuario

Tecnoware

Tecnoware ERA PLUS 600 Manual de usuario

Tecnoware

Tecnoware EVO DSP TM Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS TT 10.0 Manual de usuario

Tecnoware

Tecnoware ERA PLUS 750 Manual de usuario

Tecnoware

Tecnoware EXA PLUS Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Tecnoware

Tecnoware EVO DSP TT Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 2.0 - pf 0,9 Manual de usuario

Tecnoware

Tecnoware ATA 4.0 MM Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MODULAR Manual de usuario

Tecnoware

Tecnoware Ups Pro Manual de usuario

Tecnoware

Tecnoware EVO DSP MM 3.6 Manual de usuario

Tecnoware

Tecnoware V33/65-80-100 Manual de usuario

Tecnoware

Tecnoware EVO 3.0 RT Manual de usuario

Tecnoware

Tecnoware EXA PLUS 1000 Manual de usuario

Tecnoware

Tecnoware ERA PLUS 1600 SCHUKO Manual de usuario

Tecnoware

Tecnoware EXA LCD 2.6 Manual de usuario

Tecnoware

Tecnoware ECO STRIP 0.50 Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario

ZincFive

ZincFive BC Series Manual de usuario