Technoswitch ORYX200 Series Manual de usuario

PRMAN-0047 ORYX200 S21 Fire Panel Range Rev 02.00 220224.docx E&OE

ORYX200 RANGE

Technoswitch Conventional

Fire Control Panels

ABS, Standard & Weatherproof Versions

Rev 02.00

ORYX202 ORYX204 ORYX208 Conventional Fire Panels –INSTALLATION & OPERATION MANUAL 
 
 
PRMAN-0047 ORYX200 S21 Fire Panel Range Rev 02.00 220224.docx E&OE 
- 2 - 
INDEX 
Specifications ___________________________________________________________________________________ 4 
1INTRODUCTION ____________________________________________________________________________ 6 
1 STANDARDS _____________________________________________________________________________6 
2 CAUTIONS AND WARNINGS ________________________________________________________________6 
3 SUPPORTING DOCUMENTATION ____________________________________________________________7 
4 EN54 FUNCTIONS _________________________________________________________________________7 
5 INSTALLATION APPROVALS________________________________________________________________8 
5.1 Fire System Installations ____________________________________________________________8 
5.2 Wiring Regulations _________________________________________________________________8 
6 IDENTIFICATION OF PARTS_________________________________________________________________8 
7 INSTALLING THE ENCLOSURE ______________________________________________________________8 
8 WIRING INSTALLATION ___________________________________________________________________12 
8.1 Recommended Cable Routing _______________________________________________________12 
8.2 AC Mains Wiring__________________________________________________________________16 
8.3 Battery Positioning & Wiring_________________________________________________________17 
8.4 PSU Configuration ________________________________________________________________19 
8.5 Fault Relays/Outputs ______________________________________________________________21 
8.6 Hard Reset Function_______________________________________________________________22 
9 EXTERNAL WIRING_______________________________________________________________________22 
9.1 Sounder/Monitored Output Circuits ___________________________________________________22 
9.2 Detection Zone Inputs _____________________________________________________________23 
9.3 Relay Outputs____________________________________________________________________23 
9.4 Input Circuits ____________________________________________________________________24 
9.5 AUX DC Supply Output ____________________________________________________________25 
9.6 L-Bus Wiring_____________________________________________________________________26 
9.7 USB Connection for SOLAR_________________________________________________________26 
10 Panel Loading ___________________________________________________________________________27 
11 Battery Standby Calculation________________________________________________________________27 
2OPERATION _______________________________________________________________________________ 28 
1 INTRODUCTION__________________________________________________________________________28 
1.1 Access Levels____________________________________________________________________28 
1.2 Front Panel Controls and Indications __________________________________________________28 
1.3 Enable Controls __________________________________________________________________31 
1.4 Re-Sounding of Sounders (Evacuation)________________________________________________31 
1.5 Enabling/Disabling of Zones_________________________________________________________31 
1.6 Enabling/Disabling of Sounder Circuits ________________________________________________31 
1.7 Enabling/Disabling of Programmable Input Circuits _______________________________________31 
1.8 One-Man Walk Test Mode __________________________________________________________32 
1.9 Advanced Controls and Indications ___________________________________________________32 
3PROGRAMMABLE FEATURES AND MENU STRUCTURE__________________________________ 34 
1 PROGRAMMABLE FEATURES______________________________________________________________34 
1.1 Zones __________________________________________________________________________34 
1.2 Relays _________________________________________________________________________35 
1.3 Sounders _______________________________________________________________________36 
1.4 Inputs __________________________________________________________________________37 
2 LCD EMULATION MENU STRUCTURE (When using SOLAR)_____________________________________38 
4SERVICE AND MAINTENANCE____________________________________________________________ 41 
1 REPLACEMENT OF COMPONENTS__________________________________________________________41 
1.1 Batteries________________________________________________________________________41 

ORYX202 ORYX204 ORYX208 Conventional Fire Panels –INSTALLATION & OPERATION MANUAL 
 
 
PRMAN-0047 ORYX200 S21 Fire Panel Range Rev 02.00 220224.docx E&OE 
- 3 - 
5APPENDICES ______________________________________________________________________________ 42 
5.1 APPENDIX 1 –TROUBLESHOOTING_________________________________________________________42 
5.1.1 Troubleshooting Guide_____________________________________________________________42 
◼General Faults______________________________________________________________42 
◼Power Supply Faults _________________________________________________________42 
◼Short Circuit _______________________________________________________________43 
◼Low Resistance Fault ________________________________________________________44 
◼Incorrect EOL Resistor _______________________________________________________45 
◼High Resistance Fault________________________________________________________46 
◼False Fire Alarms and Activations_______________________________________________47 
◼Normal Operating Range _____________________________________________________48 
6WARRANTY _______________________________________________________________________________ 48 
7DISCLAIMER ______________________________________________________________________________ 48 
8REVISION INFORMATION_________________________________________________________________ 48 
 

ORYX202 ORYX204 ORYX208 Conventional Fire Panels –INSTALLATION & OPERATION MANUAL

PRMAN-0047 ORYX200 S21 Fire Panel Range Rev 02.00 220224.docx E&OE

- 4 -

SPECIFICATIONS

Item

Specification Detail

Part Number

Part Description

- ORYX202

ORYX 2 Zone FACP in ABS Enclosure

- ORYX204

ORYX 4 Zone FACP in ABS Enclosure

- ORYX208

ORYX 8 Zone FACP in Metal Enclosure

- ORYX202-W

ORYX 2 Zone FACP in Weatherproof Enclosure

- ORYX204-W

ORYX 4 Zone FACP in Weatherproof Enclosure

- ORYX208-W

ORYX 8 Zone FACP in Weatherproof Enclosure

- ORYX202-WDIN

ORYX 2 Zone FACP in Weatherproof Enclosure c/w DIN Rail

- ORYX204-WDIN

ORYX 4 Zone FACP in Weatherproof Enclosure c/w DIN Rail

- ORYX208-WDIN

ORYX 8 Zone FACP in Weatherproof Enclosure c/w DIN Rail

Enclosure

- ORYX202 & ORYX204 ABS

- ORYX202 & ORYX204 Weatherproof

- ORYX208 Standard

- ORYX208 Weatherproof

ABS: Two-tone (White lid with Anthracite Grey RAL 7016 base)

Mild Steel IP65: Matt Light Grey (ANP 37035)

Mild Steel IP30: Matt Light Grey (ANP 37035)

Mild Steel IP65: Matt Light Grey (ANP 37035)

Dimensions H x W x D (mm)

- ORYX202 & ORYX204 ABS

- ORYX202 & ORYX204 Weatherproof

- ORYX208 Standard

- ORYX208 Weatherproof

270 x 330 x 125

450 x 390 x 143

394 x 398 x 128

500 x 450 x 139

Environmental

–5 °C to +40 °C

Humidity

95% RH, Non-condensing

Weight

- ORYX202 & ORYX204 ABS

- ORYX202 & ORYX204 Weatherproof

- ORYX208 Standard

- ORYX208 Weatherproof

± 2.1 kg (excl. Batteries)

± 7.4 kg (excl. Batteries)

± 5.7 kg (excl. Batteries)

± 10.7 kg (excl. Batteries)

Cable Entries

- ORYX202 & ORYX204 ABS

Top: 6x 20 mm; 5x 25 mm

Back: 4x 20 mm; 2x 25 mm

- ORYX202 & ORYX204 Weatherproof

Bottom: 5x 20 mm; 2x 25 mm

- ORYX208 Standard

Top: 10x 20 mm; 8x 25 mm

Back: 5x 20 mm; 7x 25 mm

- ORYX208 Weatherproof

Bottom: 5x 20 mm; 4x 25 mm

LED Indicators

- ORYX202

- ORYX204

- ORYX208

3x Fire, 13x Fault (8 Hidden below lid), 8x Control & Information indications

5x Fire, 15x Fault (8 Hidden below lid), 8x Control & Information indications

9x Fire, 19x Fault (8 Hidden below lid), 8x Control & Information indications

Key Switch

Enable Controls

Event Log

1000 log events

Mains Supply

Quiescent Load

- ORYX202

- ORYX204

- ORYX208

Alarm Load

- ORYX202

- ORYX204

- ORYX208

100 –240 V AC (± 10%), 50/60 Hz, 1.0 A max

56 mA @ 110 V AC/45 mA @ 240 V AC

95 mA @ 110 V AC/65 mA @ 240 V AC

115 mA @ 110 V AC/76 mA @ 240 V AC

160 mA @ 110 V AC/56 mA @ 240 V AC

182 mA @ 110 V AC/105 mA @ 240 V AC

230 mA @ 110 V AC/130 mA @ 240 V AC

Power Supply

27.5 V DC, Switch Mode, 1.2 A load, 0.5 A max battery charging

PCB Quiescent Load

- ORYX202

- ORYX204

- ORYX208

70 mA @ 27.5 V DC

90 mA @ 27.5 V DC

108 mA @ 27.5 V DC

PCB Alarm Load

- ORYX202

- ORYX204

- ORYX208

265 mA @ 27.5 V DC

385 mA @ 27.5 V DC

410 mA @ 27.5 V DC

ORYX202 ORYX204 ORYX208 Conventional Fire Panels –INSTALLATION & OPERATION MANUAL

PRMAN-0047 ORYX200 S21 Fire Panel Range Rev 02.00 220224.docx E&OE

- 5 -

Item

Specification Detail

AUX Supply Output

24 V DC, 0.5 A

Battery Capacity

- ORYX202, ORYX204

- ORYX208

24 V 7 Ah

24 V 7 Ah, 12 Ah or 17 Ah

Battery Charging Current

0.5 A max temperature compensated

Number of Fire Zones

2, 4 or 8 Zones

Zone EOL

3k3 Ω

Zone Alarm Thresholds

220 to 900 Ω

Sounder Outputs

2x rated at 27.5 V DC, 0.3A each

Sounder EOL

3k3 Ω

General Fire Relay

30 V AC/DC, 1 A maximum

General Fault Relay

30 V AC/DC, 1 A maximum

Programmable Relays

- ORYX202

- ORYX204

- ORYX208

2 rated 30 V AC/DC, 1 A maximum

4 rated 30 V AC/DC, 1 A maximum

8 rated 30 V AC/DC, 1 A maximum

Programmable Inputs

2x fully monitored as per below

Monitored Inputs EOL

3k3 Ω

Monitored Inputs Alarm Threshold

220 to 900 Ω

L-Bus Topology and Distance

RS485 ring network @ 1,200 metre max

L-Bus Cable

PH30 or PH120, Twisted pair screened cable with a core resistance of

18.1 ohm/km

Number of Repeaters on L-Bus

7 (Seven)

The range also offers 2, 4, and 8 Zone ORYX Repeater Panels in either ABS or IP65-rated Weatherproof enclosures.

ORYX202 ORYX204 ORYX208 Conventional Fire Panels –INSTALLATION & OPERATION MANUAL

PRMAN-0047 ORYX200 S21 Fire Panel Range Rev 02.00 220224.docx E&OE

- 6 -

1 INTRODUCTION

1.1 STANDARDS

The ORYX range of Conventional Fire Alarm Control Panels is designed to comply with the following standards:

▪EN54-2: Control and Indicating Equipment

▪EN54-4: Power Supply Equipment

▪EN60950: Safety of Information Technology Equipment

▪EN50130-4: Product Family Standard

▪Electromagnetic Compatibility Directive 89/336/EEC (and the amending directive 92/23/EEC)

▪Low Voltage Directive 73/23/EEC

In addition to the basic requirements of EN54, the Fire Alarm Control Panel (FACP) offers the following EN54

optional features with requirements and additional functions not covered by EN54:

Control & Indicating Optional Functions

EN54-2 Clause

Outputs to Fire Alarm Devices

7.8

Total Loss of Power

8.4

Test Condition

Power Supply Equipment Optional Functions

EN54-4 Clause

Operation from a Main Power Supply

5.1

Operation from a Standby Battery

5.2

Monitor and Charge the Standby Battery

5.3

Recognise and Notify Supply Faults

5.4

Additional Functions

Auxiliary Power Supply Output

Auxiliary Relay Outputs

1.2 CAUTIONS AND WARNINGS

STOP

Before commencing with installation or operation of the panel, please read this manual carefully.

If you are unclear on any point DO NOT proceed. Contact the manufacturer or supplier for

clarification and guidance.

Only trained service personnel should undertake the installation, programming, and

maintenance of this equipment.

This product has been designed to comply with the requirements of the Low Voltage Safety and

the EMC Directives. Failure to follow the installation instructions may compromise its adherence

to these standards.

This equipment is constructed with static sensitive components.

Observe anti-static precautions at all times when handling printed circuit boards. Wear an anti-

static earth strap connected to panel enclosure earth point.

Before installing or removing any printed circuit boards remove all sources of power (Mains and

Battery).

This FACP is compliant with the requirements of EN54 parts 2 and 4.

Where appropriate, reference is made in this manual to the relevant sections of the EN54

standard for clarification and to ensure that the installation is compliant with the requirements of

EN54.

ORYX202 ORYX204 ORYX208 Conventional Fire Panels –INSTALLATION & OPERATION MANUAL

PRMAN-0047 ORYX200 S21 Fire Panel Range Rev 02.00 220224.docx E&OE

- 7 -

1.3 SUPPORTING DOCUMENTATION

The following documentation is available for download from our website www.technoswitch.co.za:

▪PRBOI-0011 Basic Operating Instructions for the ORYX200 S21 FACP Range

▪PRQIG-0003 Quick Installation Guide for the ORYX202 & ORYX204 S21 Fire Panels

▪PRQIG-0005 Quick Installation Guide for the ORYX208 S21 Fire Panels

▪PRMAN-0047 Installation & Operation Manual for the ORYX S21 Conventional Fire Panel Range

▪PRMAN-0048 Installation & Operation Manual for the ORYX S21 Conventional Repeater Range

▪SOFTW-0006 Battery Calculator for the ORYX S21 Range

▪SOFTW-0005 SOLAR Software

▪PRMAN-0049 SOLAR Software Installation & Operation Manual

1.4 EN54 FUNCTIONS

This FACP is compliant with the requirements of EN54 Parts 2 and 4.

In addition to the basic requirements, the following optional functions are provided, and these comply with

the requirements of EN54.

CIE Optional Functions

EN54-2 Clause

Indication

Output

Controls

Outputs to Fire Alarm Devices

Output to Fault Routing Equipment

Test Condition

7.8

8.9

PSE Functions

EN54-4 Clause

Operation from a Main Power Supply

Operation from a Standby Battery

Monitor and Charge the Standby Battery

Recognise and Notify Supply Faults

5.1

5.2

5.3

5.4

This FACP also supports the following additional functions that are not covered by EN54:

Additional Function

Refer to Paragraph

Auxiliary Power Supply Output

Auxiliary Relay Outputs

1.9.5

1.9.3

In addition to the mandatory requirements of EN54 Part 2, the Control and Indicating Equipment (CIE) supports

the following optional features with requirements:

Section 7.8

Outputs to Fire Alarm Devices

The CIE has provision for connection to Fire Alarm Devices. It is possible to Silence and Resound the alarms at

Level 2.

Refer to 1.9.3 Relay Outputs on page 23 for further information.

Section 9.5

Disablement of Points

The CIE has provision for enabling and disabling signals from points.

Refer to 2.1.5 Enabling/Disabling of Zones (page 31); 2.1.6 Enabling/Disabling of Sounder Circuits (page 31);

and 2.1.7 Enabling/Disabling of Programmable Input Circuits (page 31) for further information.

Section 10

Test Condition

The CIE has provision for testing the installation on a per zone basis.

Refer to 2.1.8 One-Man Walk Test Mode on page 32 for further information.

ORYX202 ORYX204 ORYX208 Conventional Fire Panels –INSTALLATION & OPERATION MANUAL

PRMAN-0047 ORYX200 S21 Fire Panel Range Rev 02.00 220224.docx E&OE

- 8 -

1.5 INSTALLATION APPROVALS

1.5.1 FIRE SYSTEM INSTALLATIONS

The panel must be installed and configured for operation in accordance with these instructions and the

applicable code of practice or national standard regulations for fire systems installation appropriate to the

country and location of the installation. In South Africa this would be SANS10139.

1.5.2 WIRING REGULATIONS

The panel and system must be installed in accordance with these instructions and the applicable wiring codes

and regulations (for example BS7671) appropriate to the country and location of the installation.

1.6 IDENTIFICATION OF PARTS

Figure 1 Identification of Major Panel Parts

1.7 INSTALLING THE ENCLOSURE

The panel is heavy when the batteries are installed. Use the appropriate fixing hardware to secure

the panel to the wall. Observe recommended lifting practices to guard against spinal injury.

See the table below for maximum weights:

Enclosure

Weight

Maximum

Battery

Overall Maximum Weight

ORYX202 & ORYX204 ABS

2.1 kg

7 Ah 2.5 kg

4.6 kg

ORYX202 & ORYX204 Weatherproof

7.4 kg

7 Ah 2.5 kg

9.9 kg

ORYX208 Standard

5.7 kg

17 Ah 5.5 kg

11.2 kg

ORYX208 Weatherproof

10.7 kg

17 Ah 5.5 kg

16.2 kg

▪The Standard Enclosure covers are provided with a key lock assembly for securing the hinged door to the

back box. Insert and turn the key anti-clockwise to open the enclosure.

ORYX202 ORYX204 ORYX208 Conventional Fire Panels –INSTALLATION & OPERATION MANUAL 
 
 
PRMAN-0047 ORYX200 S21 Fire Panel Range Rev 02.00 220224.docx E&OE 
- 9 - 
▪The ABS Enclosure has two screws at the bottom to secure the lid to the back box. Loosen the two screws 
and lift the lid upwards from the bottom to open the enclosure. 
▪The Weatherproof Enclosure is provided with a padlock assembly for securing the hinged door to the back 
box. Lift the lever and turn it anti-clockwise to open the enclosure. 
The chassis plate (fitted with the Main PCB) has pluggable connectors and a 90° swivel system to easily remove 
the chassis plate and allow easy access to the batteries. 
 
Figure 2 Installing the Enclosure 
It is recommended that the chassis plate be removed from the enclosure before fitting the panel to the wall. To 
remove the chassis: 
▪Unhook the chassis plate from the wing brackets and swivel 90° to slide into the vertical lock position as 
shown in Figure 2. 
▪Unplug the 8-way connector feeding the 27.5 V DC supply to the Main PCB. 
▪Carefully remove the chassis from the rear enclosure by pulling it forward out of the vertical locking 
position. Put in a safe place to prevent accidental damage. 
NB: Do not lift the chassis by holding onto any of the printed circuit cards. Hold the chassis by the metal 
plate only. 
NB: Do not remove or tamper with the “DO NOT REMOVE” sticker to screw out the harness, this will void the 
warranty. Unplug the harness only from the Main PCB and leave it connected to the PSU. 
Firstly, remove the required knockouts for the installation wiring. There are sufficient knockouts on the top of the 
ABS and Standard Enclosures for all installation wiring. In addition, there are knockouts at the top of the back 
wall for rear entry cabling, if required. 
The Weatherproof Enclosure has cable entry points at the bottom of the enclosure. Remove the rubber glands 
to utilise the cable entry point. Cable entry should only be from the bottom through the provided points with 
compression glands to ensure the integrity of the enclosure is maintained. 
The ABS and Standard Enclosures each have three fixing points and the Weatherproof Enclosure has four 
externally positioned fixing points. 
The mounting holes and dimensions of the different enclosures are indicated as follows: 
▪Figure 3: ORYX202 & ORYX204 ABS Enclosure 
▪Figure 4: ORYX208 Standard Enclosure 
▪Figure 5: ORYX202 & ORYX204 Weatherproof Enclosure 
▪Figure 6: ORYX208 Weatherproof Enclosure 
Use all mounting holes provided to ensure the panel is held securely to the wall. 

ORYX202 ORYX204 ORYX208 Conventional Fire Panels –INSTALLATION & OPERATION MANUAL

PRMAN-0047 ORYX200 S21 Fire Panel Range Rev 02.00 220224.docx E&OE

- 10 -

If the panel will be exposed to direct sunlight, an additional sun shield should be fitted to limit temperature build-

up in the enclosure.

The ABS and Standard Enclosures are provided with cable tie points that are required to properly secure the

field cabling.

The Weatherproof panel has cable channels with cable tie points on both sides of the enclosure. The cable

channels should be used to route field cables to the pluggable connectors of the Main PCB. If the DIN Rail

option was selected, the harnesses between the pluggable connectors and DIN Rail modules will be pre-

installed.

Drill the required holes in the supporting wall using an 8-mm drill bit (ABS and Standard Enclosures) or a 10-mm

drill bit (Weatherproof Enclosure) and plug with a suitable 40 mm or longer expansion plugs. Affix the panel to

the wall with M6 screws or No.10 screws for the ABS and Standard Enclosures and with M8 screws for the

Weatherproof Enclosure. Use suitable fixings to support the weight including the batteries.

Ensure there is sufficient space to allow the door to be opened when the panel is mounted.

Finally, use a brush or compressed air to remove any dust or debris from inside the enclosure.

Figure 3 ORYX202 & ORYX204 ABS Enclosure

Otros manuales para ORYX200 Series

Tabla de contenidos

Otros manuales de Panel de control de technoswitch

technoswitch

technoswitch TEC601 Manual de usuario

technoswitch

technoswitch ORYX200 Series Manual de usuario

technoswitch

technoswitch TEC247 Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas