Technical Pro MB6000 Manual de usuario

User Manual

Passive / Powered Monitor Speakers with Bluetooth® Compatibility

MODEL: MB5000 / MB6000

QUESTIONS / COMMENTS CALL 888-842-6277

or email [email protected]

P-1

WARNING!

CAUTION:TOREDUCETHERISKOFELECTRICSHOCK,DONOTREMOVETHECOVERONTHISSPEAKER.THEREARENOUSER-

SERVICEABLEPARTSINSIDE.REFER ALL SERVICINGTOAQUALIFIEDTECHNICIAN

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of "dangerous"

voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to humans. Users

should exhibit extra safety when this symbol appears in this instruction manual and follow all precautions as they are stated.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and

maintenance (servicing) instructions in this manual.

1- Read these instructions thoroughly before using this item.

2- Keep these instructions for future reference.

3- Heed all warnings.

4- Follow all instructions.

5- WARNING: To prevent fire or electric shock, do not expose this equipment to rain or moisture. Do not store or operate this

product near any liquids.

6- Clean only with a dry cloth.

7- Do not store or operate this product near any heat sources such as radiators, heat registers, stoves, or other apparatuses

(including amplifiers) that produce heat.

8- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the

other. A grounding plug has two blades and a round grounding prong. The wide blade or third prong is provided for your safety. If

the provided plug does not fit your outlet, consult an electrician for the replacement of the obsolete outlet.

9- Protect the all wires connected to this unit from being walked on or pinched, particularly plugs and the point where they exit from

the unit. When removing the cord from the power outlet, remove it by holding the plug not by pulling the cord.

10- Unplug the unit during lightning storms or when unused for long periods of time.

11- When wiring this unit and all other equipment used in connection to this unit make sure that all of your equipment is turned OFF.

12- Once installation and wiring is complete power on all your equipment with the volume and level controls turned DOWN. Once all

the equipment is ON slowly raise the volume or level controls to their proper positions.

13- When grounding this unit, be sure to do so correctly, so as not to defeat the built-in grounding in this unit.

14- Before placing, installing, rigging, or suspending any product, inspect all hardware, suspension, cabinets, transducers, brackets

and associated equipment for damage. Any missing, corroded, deformed, or non-load rated component could significantly reduce

the strength of the installation, placement or array. Any such condition severely reduces the safety of the installation and should be

immediately corrected. Use only hardware which is rated for the loading conditions of the installation and any possible short-term,

unexpected overloading. Never exceed the rating of the hardware or equipment.

15- Consult a licensed, Professional Engineer regarding physical equipment installation. Ensure that all local, state and national

regulations regarding the safety and operation of equipment are understood and adhered to.

16- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such

as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been dropped.

Introduction

Congratulations and thank you for your purchase of this Technical Pro Monitor Speakers with Bluetooth® Compatibility, the

MB5000 or MB6000.To get the most from your unit, it is recommended that you review all of the information provided in this

instruction manual before operating this equipment.

If you've spent any time at all in professional audio, you know the name Technical Pro and what it stands for —incredible

performance & sound, and the ultimate in reliability under harsh conditions. And now, Technical Pro offers the same

technology in a series of monitor speakers bringing more of what sets Technical Pro apart from all others.

MB5000 / MB6000

P-2

MB5000 / MB6000 Rear Panel:

1. Line Input (RCA): Connect your sound source to this RCA input. The line volume will be controlled by the

volume knob located on the front panel of the unit. Only passive signals should be connected to this input.

To play from the source connected to this input, press the mode button until only the RED led is illuminated.

2. Line Input (XLR): Connect your sound source (mixer) to this XLR input. The line volume will be controlled

by the volume knob located on the front panel of the unit. Only passive signals should be connected to this

input. To play from the source connected to this input, press the mode button until only the BLUE led is

illuminated.

3. Speaker Output Connector: Connect the passive speaker to this connector. Be sure the power is turned

off and the volume is turned down prior to making this connection.

4. Power Switch: Before the unit is powered on, all of the level controls should be turned down all the way.

Once powered on, slowly begin to raise the levels of the inputs. This will prevent damaging both the speaker

and the amplifier.

5. Passive Line Output (RCA): The passive line output will transmit the signal coming into the unit. Connect

this line output to a recording device or to amplifier.

6. Line Input (1/8”): Connect your sound source to this RCA input. The line volume will be controlled by the

volume knob located on the front panel of the unit. Only passive signals should be connected to this input.

To play from the source connected to this input, press the mode button until only the RED led is illuminated.

7. Power Supply: Connect the power cord here. The power switch (1) should be set to the off position before

the power supply is connected.

MB5000 / MB6000

P-3

MB5000 / MB6000 Side Panel:

8. USB Flash Drive Input: Connect a USB memory storage (flash drive) device here. The maximum size of the

USB card cannot exceed 32GB. The speaker will only play .mp3 and .wma files from the USB card input. Do

not connect your computer to this input as it will not play files directly from a computer. Once connected

use the buttons on the right side of the panel to control the USB input.

9. Bluetooth / Line Input indicator: (See Mode selector button for details).

10. Mode Selector Button: Press this button to switch between the various inputs.

To set the unit to USB Mode, press this button until the RED led is flashing

To set the unit to Bluetooth Mode, press this button until the RED & BLUE leds are flashing rapidly.

When this occurs the unit is ready to be paired with a Bluetooth device. Turn on the bluetooth function on

your Bluetooth enabled device (ie cell phone) and search for all Bluetooth connections until device names

“TECHNICAL PRO” is found and pair with the device. The pair code is “0000”--- 4 zeros. Once paired the

RED & BLUE leds will slowly flash indicating the unit has been successfully paired.

To set the unit to play from the RCA or 1/8” inputs, press this button until the RED led is illuminated.

To set the unit to play from the XLR (Mixer) input, press this button until the BLUE led is illuminated.

11. Previous Track Button- : Press this button to move to the previous track on the USB flash drive.

12. Play/Pause Button: The play / pause button will only control the USB flash drive input.

13. Next Track Button: Press this button to move to the next track on the USB flash drive.

14. Master Volume: Turn this knob to increase or decrease the master volume.

15. Treble Knob: Turn this knob to increase or decrease the treble.

16. Bass Knob: Turn this knob to increase or decrease the bass.

MB5000 / MB6000

P-4

MB5000 / MB6000 Remote:

1. Power Button: Press this button turn off the unit’s audio output.

2. Mode Selector: Press this button to switch between the input modes, Line / Bluetooth / USB.

3. Next Track / Previous Track Selector: Press these buttons to go to the next or previous track when using

the USB input.

4. Volume: Press these buttons to increase or decrease the volume.

5. Number Keypad (0-9): When the unit is playing for the USB, press the numbers to find the desired track.

6. Stop Button: Press this button to stop the playback on the USB input.

7. Mute

8. Repeat Track(s): Press this button to repeat the current track or repeat ALL tracks when playing from the

USB input.

9. Pre-set Equalizer: Press this button to switch through the pre-set equalization modes when playing from

the USB input.

10. Play / Pause Button: When the unit is playing from the USB flash drive, press this button to pause the

signal from the USB flash drive. Press this button again to play.

MB5000 / MB6000

P-5

MB5000 / MB6000 Operation:

Using the LINE (RCA), XLR (MIXER), AUX (1/8”) & USB Inputs: Power OFF the unit, and connect the Passive

speaker to the output on the powered speaker using the speaker wire. Power ON the unit and lower the

volume. Press the Mode button until the LEDs on the side panel correspond to the correct input.

To set the unit to USB Mode, press this button until the RED led is flashing

To set the unit to play from the RCA or 1/8” inputs, press this button until the RED led is illuminated.

To set the unit to play from the XLR (Mixer) input, press this button until the BLUE led is illuminated.

Slowly raise the volume to the desired levels. Adjust the bass and treble accordingly.

Using the Bluetooth Input: Power OFF the unit, and connect the Passive speaker to the output on the

powered speaker using the speaker wire. Power ON the unit and lower the volume. Press the Mode button

until the LEDs on the side panel correspond to the correct input.

To set the unit to Bluetooth Mode, press this button until the RED & BLUE leds are flashing rapidly.

When this occurs the unit is ready to be paired with a Bluetooth device. Turn on the bluetooth function on

your Bluetooth enabled device (ie cell phone) and search for all Bluetooth connections until device names

“TECHNICAL PRO” is found and pair with the device. The pair code is “0000”--- 4 zeros. Once paired the

RED & BLUE leds will slowly flash indicating the unit has been successfully paired.

Once successfully paired you will be able to play music directly on the unit directly from the Bluetooth

device. Slowly raise the volume to the desired levels. Adjust the bass and treble accordingly.

The Bluetooth word mark and logos are registered trademarks owned by SIG, Inc. and any use of such marks by Technical Pro is under

license. Other trademarks and trade name are those oftheir respective owners.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY

INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Federal Communications Commission Requirements:

The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction, may cause harmful interference to radio communication. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

●Increase the separation between the equipment and receiver.

●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

●Consult the dealer or an experienced radio/TV technician for help.

THE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE

COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

FCC Radiation Exposure Statement

The equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio

frequency (RF) Exposure Guidelines in Supplement C to OET65. The equipment has very low levels of RF energy that it is

deemed to comply without testing of specific absorption ratio (SAR).

MB5000 / MB6000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Altavoces de monitorización de otras marcas

Lynx

Lynx ADP-28M Manual de usuario

Klipsch

Klipsch Reference Premiere RP-160M Manual de usuario