Technibel MCE089ZAA Manual de usuario

Heat pump with heating and cooling floor

Operating instructions

Control unit

1) Temperatures display

Zone selection with key Z/OK.

By default, the current set point is displayed.

The cursor is displayed near the symbol when the system is operating in override

with a Typhone 500 telephone remote control unit. Heating mode - ZONE1 - only)

2) COOLING mode

Set

the knob to

COOL

The setpoint

temperature

is displayed.

Cooling setpoint

temperature adjustment

(20˚C to 30˚C)

The setting mode is exited

after 5 seconds

if no key is pressed.

EXT

0h 2 4 6 8 10 12 14 16 18 20 22 24

Z OK

110

Validation or zone change key

Button selection mark

Electric heating only

Electric heating ON

Temperatures

Display zone 1, zone 2 (if any)

or outside temperature

Comfort override activated

Current program

Current day

( : Comfort, : Economy)

Modification or override keys

Away***

Cooling

mode

Hourly program mode

Comfort

Economy

Hourly programming

Stop

Time setting

Two cases are possible in the case of an installation with 2 zones:

• zone 2 = floor: the unit displays the temperatures for each zone

• zone 2 = terminal units: the unit displays either HEAT in heating mode

or COOL in cooling mode. The configuration is determined when commissioned.

0h 2 4 6 8 10 12 14 16 18 20 22 24

Display of the

current setpoint

and program

of zone 1

Display of the

current setpoint

and program

of zone 2 (possible)

Outside

temperature

display

At any time, pressing

and holding (5 sec.)

the key will display

the ambient temperature

of the zone.

Note : electronic controller configura-

tion is to be set by a technician during

starting up according the installation

type.

3) HEATING Mode

3.1 Comfort mode

3.2 Economy mode

3.3 Long-term absence mode (away) - Frost protection

3.4 Hourly programming mode

3.5 Set point override by telephone control TYPHONE 500

- only in heating mode (do not operate in cooling mode)

- only for zone 1

The user can :

- know the ambient temperature of zone 1,

- know the current set point temperature of zone 1,

- send an override set point for zone 1.

During override, zone 1 operates in “Comfort” mode with the new

temperature set point.

This override is indicated by an index on the display.

Any action on the rotary knob deactivates the override.

Note : This function is possible only after entering the password (given by

the installer) by means of the phone keyboard.

Press the key as many

times as necessary

to select a Comfort override

0h 2 4 6 8 10 12 14 16 18 20 22 24

0h 2 4 6 8 1012141618202224

Set

he knob

The unit followings

the programming

If not pressed

for 3 seconds,

the override is validated.

The hourglass icon flashes.

The key enables you to go back during the override duration programming step.

Set

the knob

The corresponding

setpoint is displayed

The frost protection

temperature is set at 12˚C

0h 2 4 6 8 10 12 14 16 18 20 22 24

Set

the knob

The Economy

setpoint is displayed

The Economy temperature is indexed to the

Comfort temperature (adjustable in the installer menu).

Default value: Economy = Comfort - 2˚C

Set

the knob

0h 2 4 6 8 10 12 14 16 18 20 22 24

The Comfort setpoint

is displayed Set the new Comfort

setpoint from

15˚C to 25˚C (ex.: 21.5˚C)

The setting mode

is exited after 5 seconds

if no key is pressed.

Phone comfort

override index

New current set

point for zone 1.

EXT

4) Time and date adjustment

5) Programming

6) Stop

7) Parameterisation

From any knob position, simultaneously press and hold keys

and

for 5 seconds, until the screen displays PArA, then select

user / installer menu.

To move from the user menu to the installer menu, press

- = user menu: certain parameters may only be consulted,

- = installer menu: protected access by password for modification (for installer use only).

Select the first parameter by pressing

on Z/OK.

Press the or keys to shift from one parameter to another.

Set

the knob to

1 h comfort

1 h reduced

0h 2 4 6 8 10 12 14 16 18 20 22 24

Set

the knob

on PROG Z1

The 1st time

slot flashes Ex.: Comfort from 7h to 9h,

from 12h to 14h,

from 19h to 23h

Repeat

the procedure

for each time slot

Validate and continue

to the next day.

Repeat the procedure

for each day.

o modify the programming for zone 2 if this one is activated, set the knob to and repeat the operations above.

Set

the knob

The current day

flashes Select the desired

day and validate

by pressing OK.

Set the hour using

and validate

by pressing OK.

Set the minutes

using

and vali

by pressing OK.

To exit the parameterisation menu, press and hold for 5 seconds or modify the

position of the selector knob.

List of parameters that can be consulted by the user:

8) Alarms

If an alarm message appears, contact the After-Sales Service.

Outside temperature

Installation water return temperature

Installation water outlet temperature

Resulting water temperature setpoint, zone 1

Resulting water temperature setpoint, zone 2

Water temperature, zone 1

Water temperature, zone 2

Ambient Temperature zone 1

Ambient Temperature zone 2 (floor)

Generator output status

Generator mode output status (h/c) (1=h)

Outlet status, Support heater Elec. - 1

Outlet status, Support heater Elec. - 2

Outlet status, Support heater Elec. - 3

Outlet status - water pump ZONE 1

Outlet status - water pump ZONE 2

Outlet status - valve control ZONE 1

Outlet status - valve control ZONE 2

(heating floor)

Parameters available for installations with 2 ZONES.

Note : Flashing display without alarm message indicates that the water temperature is momentary not convenient

for the heat pump. Call the After-Sales Service only if this fact persists.

* Manual reset by stoppin

the device ("OFF"). Call the after-sales service.

The unit displays: Generator fault The unit displays:

Water probe fault, zone 2

(in the case of 2 zones only)

Heater fault Ambiance probe fault Z1

Ext. air probe fault

Ambiance probe fault, Z2

(in the case of 2 zones only)

Installation water return

probe fault

Communication

or system fault

Output water probe fault

installation

Water output fault

Water probe fault, zone 1

(in the case of 2 zones only)

In heating mode, the generator

fault causes the installation

to switch to Frost Protection mode.

It is possible to restart in heating

mode by pressing and holding OK.

The symbol is displayed.

Attention, in this case, heating is

provided only by the supplementary

electric heating.

High water

temperature fault*

Communication fault

with zone 2 board.

Communication fault

with zone 1 board.

Simultaneously press and hold

the + and - ke

s for 5 seconds.

1: User

2: Installer

Access to the 1st

parameter (P01) Display of the

parameter value

Otros manuales de Bomba de calor de Technibel

Technibel

Technibel Liberty300 Solar Manual de usuario

Technibel

Technibel Liberty300 Solar Manual de usuario

Technibel

Technibel PHRIE 095 Manual del propietario

Technibel

Technibel PHRV 22 Manual de servicio

Technibel

Technibel Liberty 300 Manual de usuario

Technibel

Technibel PHR 6 Manual de usuario

Technibel

Technibel KH2ZM Manual de usuario

Technibel

Technibel PHRT 7 Manual del propietario

Technibel

Technibel PHRIE Series Manual de usuario

Technibel

Technibel AF UIH Series Manual de usuario

Technibel

Technibel Liberty300 Solar Manual de usuario

Technibel

Technibel PHRT 9 Manual de usuario

Technibel

Technibel Liberty300 Solar Manual de usuario

Technibel

Technibel PHRIA 105 FAA Manual de usuario

Technibel

Technibel PMHRV 2044 Manual de usuario

Technibel

Technibel CHGF Series Manual del propietario

Technibel

Technibel Liberty300 Solar Manual de usuario

Technibel

Technibel Liberty300 Solar Manual de usuario

Technibel

Technibel HKE 609R57I Documento técnico

Technibel

Technibel M2Z P Manual de usuario

Manuales populares de Bomba de calor de otras marcas

MICROWELL

MICROWELL HP 1000 GREEN Manual de usuario

Sanyo

Sanyo SAP120FCH Manual de usuario

Daikin

Daikin EHYHBH05AA Manual de usuario

Panasonic

Panasonic WH-SDF03E3E5 Guía

Bryant

Bryant 544B Manual de usuario

Airxcel

Airxcel 45000 Series Manual

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manual de usuario

Dimplex

Dimplex LI 16I-TUR Guía del usuario

Carrier

Carrier WSHP Open v3 Guía de configuración rápida

TGM

TGM CTV14CN018A Manual de usuario

Carrier

Carrier 38MGQ Series Manual de usuario

Kokido

Kokido K2O K880BX/EU Guía de solución de problemas

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guía rápida

Carrier

Carrier 48EZN Manual de usuario

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Instrucciones de funcionamiento

Ariston

Ariston NIMBUS Manual de usuario

Weishaupt

Weishaupt WWP L 7 Guía del usuario

GE Zoneline AZ85H09EAC Manual de usuario