Techni Mobili RTA-B018 Manual de usuario
ROLLING LAPTOP CART WITH STORAGE
MODEL RTA-B018
ASSEMBLY INSTRUCTIONS
REV.FCS-6922-1022
Thank you for purchasing our product
Scan QR code to view
full assembly video
•Please be kind to our planet, when done with the assembly,
recycle any of the packaging materials that is accepted by
your city or recycling service. Thank you!
P.1 P.1
RTA-B018
•Please read carefully the assembly instructions before the installation.
• Do not discard this manual or any of the packaging
material until the unit has been completely assembled.
•Scan this QR code to view the complete assembly video online.
•For individual Step videos - please use the QR code found on
the corresponding step within the manual. SAMPLE - DO NOT SCAN
P.2 P.2
RTA-B018
1
x1 2
x1 3
x1
4
x1
Top panel
The replacement parts service is limited to
the 48 contiguous United States.
If you reside in AK, HI, PR, U.S. territories
or other countries,
please contact the
supplier from where
the unit was purchased.
Missing, damaged and defective
parts can be replaced at no cost
to you. Please refer to the last
pages on this manual.
Do a quick inventory
of all the parts and
hardware listed below
MAIN PARTS LIST
Left frame Right frame
Back panel
5
x2 6
x1 7
x1
8
x1
Shelf Drawer front panel Drawer left panel
Drawer right panel 9
x1 10
x1
Drawer back panel Drawer bottom board
H
P.3 P.3
RTA-B018
PART QTY SIZE
MAIN PARTS LAYOUT (For reference)
HARDWARE LIST
4M6x50
A
ITEM
1M4 Allen Wrench
1
8
B
4
C
8
D
4
E
4
F
4
G
PART QTY SIZE
2Non-locking
caster (back)
H
ITEM
2
J
INCLUDED TOOLS
Phillips Screwdriver
M6x30
M6x30
Bolt
M4x12
M4x35
M6x12
Cam lock
Sliders
23
4
56
7
8
9
10
I
5
2Locking
caster (Front)
I
1Hex Wrench
(Spanner)
OTHER TOOLS YOU WILL NEED BUT
NOT INCLUDED WITH THE PRODUCT
1
M12
P.4 P.4
RTA-B018
BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
• If during assembly you find an issue or need clarification,
please contact our Customer Service for assistance.
Please refer to the last pages on this manual.
• On each step read the instructions thoroughly and
analyze the illustrations before proceeding to do the
assembly.
• Follow the instructions step by step and do not skip any
unless our Customer Service advises it is OK to do so.
• Do not overtighten or force the screws as they might
break, strip, damage the threads of the holes or get stuck
inside the part.
• Make sure you understand which hardware will be
used on each step. Using the wrong size of screw,
bolt or pin might strip the threads or cause damage
to the part in which it is being used.
• To avoid misalignments, always leave the screws loose
and tighten them until all pieces are positioned correctly.
• If the hole seems too small for the screw, make sure you
are using the correct size of screw and/or that you are
installing it in the correct hole.
• Do not discard this manual or any of the packaging
material until the unit has been completely assembled.
√
√
M6
30mm
M6x30
•Sometimes on the panels the laminate or material might be
covering the hole partially or entirely. If there is no visible
hole or it seems too small, pass and press the tip of your
finger over the area where the hole should be located to feel
its indentation, and once found, carefully pierce the laminate
to uncover the hole underneath.
Clear the front hole by moving away the piece with ball bearings
(Front)
P.5 P.5
RTA-B018
STEP 1
Hardware
JSliders 2
Pcs
(Front)
ASSEMBLY STEPS
(Top)
(Bottom)
Scan QR to view step
STEP 2
Hardware
DM4x12 4
Pcs
J-1 Big piece 2
Pcs
Tools (Not included)
Scan QR to view step
Grab and extend each of the sliders Jtowards your RIGHT and separate
the small track from the rest by pressing UP firmly the locking lever, at
the same time that you pull the small track out. The big pieces J-1 will be
used in the next step, while the small tracks J-2 will be used until step 9,
so please set them aside.
On the big sliders J-1 slide the piece with the ball bearing towards the
middle to clear the opening for the front hole, then attach the sliders to
the top bar on the left frame 2and the right frame 3with screws Dusing
a screwdriver (not included).
(Front) Push
lever
UP Separate
small
track
J
J-1 J-2
Big pieces: Use on next step Small pieces: Use until step 9
(Front) (Front)
(Front)
(Front)
(Front)
(Front)
(Front)
23
J-1J-1
J-1
DO NOT TIGHTEN THE SCREWS,
leave them all loose to allow flexibility for the next steps.
P.6 P.6
RTA-B018
STEP 3
Hardware
HNon-locking
2
Pcs
4
I
I
Locking
2
Pcs
Tools (included)
Scan QR to view step
STEP 4
Hardware
FM6x12 4
Pcs
Tools (included)
Scan QR to view step
Attach the casters Hand Ito the bottom of the frames 2and 3using the
wrench, and following this order:
• The Non-Locking casters Hgo at the back of the frame.
• The Locking casters Igo at the front
Assemble the back panel 4to the frames 2and 3with screws Fbut do
not tighten yet. The screws go through the tabs on the frames and into
the panel.
23
Non-Locking
go at the back
Locking
go at the front
H
(Front) (Front)
(Back)
(Back)
(Top)
(Bottom)
(Top)
(Bottom)
23
M12
• Assemble the shelf panels
P.7 P.7
RTA-B018
STEP 5
Hardware
AM6x50 4
Pcs
1
23
5
Tools (included)
Scan QR to view step
STEP 6
Hardware
BM6x30 8
Pcs
Tools (included)
Scan QR to view step
• Place the tabletop 1upside-down on the floor over a blanket to
protect its surface, and place the frames 2and 3over it making the
holes coincide, and secure with screws Abut do not tighten yet.
• Turn the unit over its back side to have it ready for the next step.
5to the middle and bottom bars on the
frames 2and 3with screws Bfrom underneath as shown, but do not
tighten any screws until finished with this step.
• Afterwards, you can proceed to tighten all the screws left loose from
steps 4,5and 6, and turn the unit upright.
DO NOT TIGHTEN THE SCREWS,
leave them all loose to allow flexibility for the next steps.
(Front)
(Back)
DO NOT TIGHTEN THE SCREWS
until this step is finished.
2
3
5
P.8 P.8
RTA-B018
STEP 7
Hardware
EM4x35 4
Pcs
10
C
G
Tools (included)
Scan QR to view step
STEP 8
Hardware
CBolt 4
Pcs
GCam lock 4
Pcs
Tools (NOT included)
Scan QR to view step
• Assemble the drawer side panels 7and 8to the drawer back panel 9
with screws Efrom the side.
• Slide the drawer bottom panel 10 through the grooves of the side
panels 7and 8, and into the groove of panel 9
• Attach the bolts Cto the front panel 6.
• Join panel 6to panels 7and 8.
• Insert the cam locks Ginto panels 7and 8and turn them to lock all
the 3 panels. Please pay attention to the cam lock alignment.
Cam locks
alignment
on 7 and 8
(Front)
(Front)
7
8
9
7
8
9
All the grooves
must match at
the bottom
6
6
7
87
8
P.9 P.9
RTA-B018
STEP 9
Hardware
DM4x12 4
Pcs
(Front)
J-2 Small piece 2
Pcs
Tools (NOT included)
Scan QR to view step
STEP 10
Scan QR to view step
Attach the small sliders J-2 to the side panels 7and 8with screws D
.• On the frame first make sure that the piece with the ball bearing is all
the way to the front.
• Insert the drawer making sure that simultaneously on both sides, the
tracks J-2 on the drawer go through the black plastic guides and the
ball bearing pieces on the sliders J-1.
• Push in the drawer slowly into the unit.
1. The ball bearings in
J-1 must be at the front
2. J-2 goes through the
plastic guide and the
ball bearings on J-1
3. Push in
very slowly.
7
8
(Front)
(Front)
J-2
J-1 J-1
J-2
J-2
J-2
Otros manuales para RTA-B018
2
Tabla de contenidos
Otros manuales de Carrito para exteriores de Techni Mobili
