Technetix XGT XGTZ-2-4T Manual de usuario

technetix.com

+1 (720) 931-6480

[email protected]

12/2021-AE/V1

User manual

XGT 10 gigabit

modular outdoor taps

2XGT_User Manual

Contents

Safety 3

Intended audience 3

Tools list 3

Overview 4

Chapter 1 User applications

1.1 Mass deployment 5

1.2 Fixing the cables to the IN and OUT connectors 6

1.3 Base installation of IN and OUT connectors 7

1.4 Signal conditioning 7

1.5 Tightening sequence of faceplate bolts 8

1.6 Installing drop cables on a faceplate 8

1.7 Strand mount mechanism 9

Chapter 2 New builds and maintenance 9

2.1 Basic assembly 9

2.2 Bill of materials 10

2.3 Example installations 11

1. Install full tap 8-way 14 dB 11

2. Replace coupler module (CM)

without any power loss using

make before break tool (MBBT) 12

Order Information

Tap components 15

Coupler module removal tool (CMRT) 15

MBBT 15

Tap components 17

Signal conditioning 16

3technetix.com

The XGT 10 gigabit modular outdoor tap user manual is intended for network engineers and

technicians responsible for planning, conﬁguring, installing and testing the Technetix XGT

outdoor tap. Installers should have a working knowledge of coaxial cable and line powering

systems and cabling practices.

Tool list

The following tools and supplies are required when installing an XGT outdoor tap:

˺3/8" (10 mm) nut driver for lid bolts

˺Torque limiting spanner (wrench) tool 30 in/lbs (3.5 N-m) for F-connectors

˺Torque limiting spanner (wrench) tool 40 in/lbs (4.5 N-m) for KS 5/8 connectors

˺XGT-MBBT for power passing while removing coupler modules

˺XGT-CM-RT for easy removal of coupler modules

SAFETY

Warning: The center pin becomes live when the ﬁrst connector is inserted – don’t touch anything else

with second connector – this will cause a shock.

PRODUCT INFORMATION: 19013994 XGT-MBBT XGT make before break tool

19014361 XGT-CM-RT XGT coupler module removal tool

4XGT_User Manual

Overview

˺Modular platform DOCSIS 4.11 compatible

˺3 GHz housing

˺1.8 GHz coupler module, also compatible with

1.2 GHz systems

˺1.8 GHz front plates: 2-way, 4-way and 8-way

˺Low inventory standardised modular solution2

˺one housing

˺three front plates

˺5 or 6 CM tap values

˺9 or 10 SKUs for a full multitap

˺3 GHz housing with superior seizure-less

connector design3

˺Faceplate removable without breaking

RFsignals and line power

˺Install now when upgrading or carrying out

routine maintenance:

˺1.2 GHz DOCSIS 3.1 ready now

˺1.8 GHz DOCSIS 4.0 ready now

˺3.0 GHz DOCSIS 4.1 ready housing

1Faceplate (XGT1800-FPx)

2Signal conditioning plug-in

3Directional coupler module (XGT1800-CMxx)

4Housing / Backbox (XGT3000-BB)

1. DOCSIS 4.1, the next generation after DOCSIS 4.0, taking bandwidth from 1.8 GHz to 3 GHz 25 Gbps data capacity.

2. With DOCSIS 4.1 all legacy Regal, GI-Moto, SA-Cisco and Magnavox housings become obsolete.

3. The futureproof XGT housing has enables a secure 3GHz connection without screws and excellent protection

against common path distortion (CPD).

5technetix.com

Fully assembled 2-way 1.8 GHz Fully assembled 4-way 1.8 GHz Fully assembled 8-way 1.8 GHz

XGTZ-2-4T

XGTZ-2-8 XGTZ-4-8T

XGTZ-2-11 XGTZ-4-11 XGTZ-8-11T

XGTZ-2-14 XGTZ-4-14 XGTZ-8-14

XGTZ-2-17 XGTZ-4-17 XGTZ-8-17

XGTZ-2-20 XGTZ-4-20 XGTZ-8-20

XGTZ-2-23 XGTZ-4-23 XGTZ-8-23

XGTZ-2-26 XGTZ-4-26 XGTZ-8-26

XGTZ-2-29 XGTZ-4-29 XGTZ-8-29

Item code Description

XGTZ-2-4T 10 gigabit taps facilitate the provision of 10 Gbit/s speeds to customers in the future

XGTZ-2-4T Z is a 1.8 GHz assembly (including the faceplate and CM)

XGTZ-2-4T 2-way faceplate

XGTZ-2-4T4 dB tap attenuation

XGTZ-2-4T Terminated housing for end-of-line situations

Chapter 1 User applications

1.1 Mass deployment

While the modularity of the XGT range is ideal for

maintenance and small deployments, it is recommended that

fully assembled multitaps are used for mass deployments

and entire network upgrades where 1 GHz and 1.2 GHz units

are all being replaced.

After a mass deployment it is recommended that individual

SKUs from the XGT range are used for ongoing maintenance

and upgrades to fully beneﬁt from the modular approach and

the lower inventory requirements.

6XGT_User Manual

1.2 Installing cables to the IN and OUT connectors

The housing is ﬁtted with a spring loaded 5/8 female connector (Fig. 1), designed to ﬁt a standard KS 5/8 male connector

without the need to secure the pin with a screw contact (unlike legacy multitaps).

1. Cut the 5/8 pin to a length of 1.34” (34 mm) with a tolerance 0.039” (+/- 1 mm) also marked on the back

of the housing (Fig. 2).

2. The XGT 5/8 female connector takes pins with a diameter of 0.065” – 0.075” (1.65 - 1.91mm).

3. Torque the KS connectors to 40 in/lbs (4.5 N-m).

Pin length 1.34" (34 mm)

IMPORTANT: The total pin length = pin length and connector thread length (Fig. 3).

Fig.2

Fig. 1

Fig. 3

7technetix.com

1.3 Base installation of IN and OUT connectors

If installing a multitap and both cables come from the same direction, you can relocate the “blind plugs” to the side ports (Fig. 4),

making sure they are torqued at 40in/lbs (4.5 N-m), then the shielding eectiveness against 4G/5G signals remains high.

1.4 Signal Conditioning

Signal conditioning is used in certain networks to give a speciﬁc amount of tilt to the tap ports enabling them to reach homes

with a ﬂat signal. In the XGT platform the signal conditioning plug-ins can be installed in the faceplate, which are all delivered

with a 0 dB jumper. When installing a cable equalizer or cable simulator, the 0 dB jumper in the faceplate will be replaced by the

signal conditioning plug-in.

Available plug-ins Cable simulator Cable equalizer

1.2 GHz optimized XGT1200-CSxx XGT1200-CExx

1.8 GHz optimized XGT1800-CSxx XGT1800-CExx

Fig. 4

8XGT_User Manual

1.5 Tightening sequence of faceplate bolts

Fully tighten to 30 in/lbs (3.5 N-m) in the following sequence:

1.6 Installing drop cables on the faceplate

Fix the F-male connector to the drop cables while connecting to customer premises at the front F-female ports of the

multitap, then tighten the connectors to 30 in/lbs (3.5 N-m) torque. Make sure all F-ports that are not in use are terminated

with a 75 Ohm terminator also to 30 in/lbs (3.5 N-m) torque.

Top bolt Bottom bolt Left hand bolt Right hand bolt

1 2 3 4

9technetix.com

1.7 Strand mount mechanism

Undo the bolt to secure the stand cable. Tighten the bolt to 30 in/lbs (3.5 N-m) torque.

Chapter 2 New builds and maintenance

The modularity of the XGT range is ideal for maintenance and small deployments, it is recommended that a fully assembled

multitap is used for mass deployments and entire network upgrades.

2.1 Basic assembly

Housing (backbox) + coupler module + faceplate = full multitap

10XGT_User Manual

Type Description

XGT3000-BB TECHNETIX 10 GIGABIT TAP BACK BOX 3.0 GHZ

XGT3000-BBT TECHNETIX 10 GIGABIT TAP BACK BOX 3.0 GHZ TERMINATED

XGT1800-FP2 TECHNETIX 10 GIGABIT TAP FACEPLATE 2-WAY

XGT1800-FP4 TECHNETIX 10 GIGABIT TAP FACEPLATE 4-WAY

XGT1800-FP8 TECHNETIX 10 GIGABIT TAP FACEPLATE 8-WAY

CM / dB value for the complete tap

2-way 4-way 8-way

XGT1800-CM0T TECHNETIX XGT DIRECTIONAL COUPLER MODULE 0T dB 4T 8T 11T

XGT1800-CM04 TECHNETIX XGT DIRECTIONAL COUPLER MODULE 04 dB 811 14

XGT1800-CM07 TECHNETIX XGT DIRECTIONAL COUPLER MODULE 07 dB 11 14 17

XGT1800-CM10 TECHNETIX XGT DIRECTIONAL COUPLER MODULE 10 dB 14 17 20

XGT1800-CM13 TECHNETIX XGT DIRECTIONAL COUPLER MODULE 13 dB 17 20 23

XGT1800-CM16 TECHNETIX XGT DIRECTIONAL COUPLER MODULE 16 dB 20 23 26

XGT1800-CM19 TECHNETIX XGT DIRECTIONAL COUPLER MODULE 19 dB 23 26 29

XGT1800-CM22 TECHNETIX XGT DIRECTIONAL COUPLER MODULE 22 dB 26 29 32

XGT1800-CM25 TECHNETIX XGT DIRECTIONAL COUPLER MODULE 25 dB 29 32 35

2.2 Bill of materials

Cross-reference the table below to determine the CMs required. The module number refers to the attenuation level

in dBs (to the faceplate). The faceplate adds the 2, 4 and 8-way splitter loss due to the number of ports on the faceplate.

The ﬁnal values for tap loss are detailed in the table below.

A simple way to check that you have the correct couple module is to check the colored label. This will give you the dB values

the coupler will provide in combination with a 2, 4 or 8-way faceplate.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de technetix

technetix

technetix G.hn Powerline Wi-Fi Manual

technetix

technetix AIMA3000 Manual operacional

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario

technetix XGT XGTZ-2-4T Manual de usuario

Manuales populares de Hardware de red de otras marcas