TECHLIGHTING ELEMENT E6_LO-C_N Series Manual de usuario

Installation Instructions for 920E6OLN-C

Round or Square Type Non-IC Housing for Open

Flangeless Trims, with Ceramic Metal Halide Lamp

E6_LO-C_N-_ 1.0

CERAMIC METAL HALIDE - ROUND/SQUARE FLANGELESS

GENERAL PRODUCT INFORMATION:

This product is suitable for damp locations.

This instruction shows a typical installation.

Install the Housing with Adjustable Bars

CAUTION - RISK OF FIRE

This product requires installation by a qualified

electrician. Before installing be sure to read all

instructions and DISCONNECT POWER TO THE

ELECTRICAL BOX.

Slide the inner adjustable bar completely through the

three housing clasps. Make sure the attached nail is on top.

Slide and push the outer adjustable bar completely onto

the inner adjustable bar so that the tab clicks into place

behind the stop point.This will prevent the adjustable bars

from coming apart.

Repeat steps 1 & 2 for the other side of the housing.

HOUSING CLASP

HOUSING

1A INNER ADJUSTABLE BAR

OUTER ADJUSTABLE BAR

TAB

STOP POINT

NOTE: If using the butterfly brackets, skip these

steps and refer to "Install the Housing with

Butterfly Brackets" on page 2.

NAIL

Align the adjustable bars so that the trim holder is exposed

below the joists just enough to match with the drywall

thickness.

Level the adjustable bars and, with a hammer, tap the nails

completely into the joists to secure the adjustable bars in

place.

TRIM HOLDER

NAIL

JOIST

NAIL

NOTE: The adjustable bars can be mounted to

joists that are spaced 16" - 24" apart.

NOTE: The trim holder is 1/2” high. When

installing the adjustable bars to joists, make sure

the bottom of the trim holder matches with

bottom of the drywall.

Adjust the horizontal position of the trim holder by sliding

the housing on adjustable bars.

When the desired location is achieved, tighten the two self-

tapping screws to lock the housing onto the adjustable

bars.

TRIM HOLDER

NOTCH

HOUSING

ADJUSTABLE BAR

NOTCH

SELF TAPPING SCREW

HOUSING

TRIM HOLDER

NOTE: Notches in trim holder can be used to

align multiple housings using a laser or string.

Install the Housing with Butterfly

Brackets

NOTE: Skip to Page 3 if installing the housing

with adjustable bars.

BUTTERFLY

BRACKET

BEVELED

CORNER

Loosen the wing nut.

Slip the button head screw through the large opening in

the housing slot. Make sure the beveled corners of the

butterfly bracket are toward the bottom of the housing.

Slide the butterfly bracket within the slot to the desired

height, and tighten the wing nut to secure the bracket.

Repeat steps 1-3 for the other side.

Use the butterfly brackets to mount the housing, according

to local building codes and electrical codes.

(Do not remove)

SLOT

WING NUT

NOTE: Notches in trim holder can be used to

align multiple housings using a laser or string.

Connect Power to the Housing

Connect the white wires to the neutral power line wire

with the included lever nut.

Connect the black wire to the hot power line wire with the

included lever nut.

Connect the green wire and bare wire to a suitable ground

according to local electrical codes.

Replace the electrical box cover. Make sure that the top

edge of the cover snaps under the tabs.

TABS

ELECTRICAL

BOX COVER

CONDUIT

Push up the tabs on the electrical box and remove the

electrical box cover.

NOTE: Before installing drywall or acoustic

panel, power up and run the Element fixture(s)

for 10 minutes to make sure that all electrical

connections are tight and secure. Refer to page 6

to install the lamp for testing.

Install the conduit to the housing electrical box.

Run the power line wires into the housing electrical box.

WARNING: RISK OF FIRE. When using the

housing electrical box for power feed through,

use 8 - #12 AWG branch circuit wires.

MAX

Install Drywall

6-3/8" 6-3/8"

For housings with round trim holder, mark a 6-3/8"

diameter circle on drywall. Cut out the marked section.

For housings with square trim holder, mark a 6-3/8" square

on drywall. Cut out the marked section.

ROUND TRIM HOLDER SQUARE TRIM HOLDER

1a 1b

Align the cut out section with the trim holder and install

drywall.

WARNING: The housing is not

intended to be in contact with or covered with

combustible materials and insulation. Do not

install insulation within 3 inches of the housing

sides or above in such a manner to entrap heat.

Risk of Fire:

DRYWALL

4C TAB

CUT OUT

Line up the two tabs in back of the plaster ring with the

two cut out sections of the trim holder inside edge.

Push the plaster ring tabs into the cut out sections of the

trim holder edge.

ROUND PLASTER RING SQUARE PLASTER RING

CUT OUT

TAB

3 3

LENS LOCK

#8-32 SCREW #8-32 SCREW

Secure the plaster ring in place with the two provided flat

head #8-32 screws. Make sure that the screws penetrate

through the drywall into the housing screw holes.

Finish around the trim to match drywall.

Plug the trim holder with the provided dust shield.

Properly plaster onto the plaster ring and drywall.

LENS LOCK

NOTE: Do not overtighten the screws!

Overtightening may bend the plaster ring,

causing the plaster surface to come away from

the drywall.

Line up the trim with the opening, and push the trim

completely into the housing. Arrows on the trim and in the

opening indicate the proper orientation.

REFLECTOR 3

Install the Trim and Lamp

SAVE THESE INSTRUCTIONS!

Screw the lamp completely into the socket.

LAMP

Use 120 Volt 20 Watt Medium Base

Ceramic Metal Halide lamp with housings

E6RLO-C20_ and E6SLO-C20_

Use 120 Volt 39 Watt Medium Base

Ceramic Metal Halide lamp with housings

E6RLO-C39_ and E6SLO-C39_

Use 120 Volt 70 Watt Medium Base

Ceramic Metal Halide lamp with housings

E6RLO-C70_ and E6SLO-C70_

Clip the carabiner onto the hoop inside the housing.

Connect the trim power plug to the connector inside the

housing, on the electrical box side of the housing.

CARABINER

SAFETY

CABLE

NOTE: This section illustrates a square trim.

Round trim pieces install the same way.

HOUSING

OPENING

POWER

PLUG

HOOP (INSIDE)

POWER

CONNECTOR

(INSIDE)

HOOP

SAFETY

CABLE

CARABINER

POWER

PLUG

POWER

CONNECTOR

NOTES

7400 Linder Ave, Skokie, IL 60077

847.410.4400

www.element-lighting.com

is a registered trademark of Element. Element reserves the right to

change specifications for product improvements without notification.

A Generation Brands Company

Otros manuales de Equipo de iluminación de TECHLIGHTING

TECHLIGHTING

TECHLIGHTING Mona Lisa Manual de usuario

TECHLIGHTING

TECHLIGHTING Element CMH MR16 Manual de usuario

TECHLIGHTING

TECHLIGHTING ELEMENT E3-L AE Series Manual de usuario

TECHLIGHTING

TECHLIGHTING tiella Sola Pack Manual de instrucciones

TECHLIGHTING

TECHLIGHTING UNILUME 700UCRD Series Manual de usuario

TECHLIGHTING

TECHLIGHTING Cirque Small 700CQS Manual de usuario

TECHLIGHTING

TECHLIGHTING T-trak 700TTSCCADJ Series Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario