TechBook In.touch 2 Manual de usuario

in.touch 2

TechBook

Gecko Alliance

450 des Canetons, Québec (Qc), G2E 5W6 Canada, 1.800.78.GECKO

www.geckoalliance.com Printed in Canada

9919-101517-B

Rev. 02-2017

All trademarks or registered trademarks

are the property of their respective owners.

Simplest of setups

Strong and long range communication signal

State-of-the-art apps with push notiﬁcations

ultimate Wi-Fi remote control for your spa

Warning �� 2

Introduction �� 3

Overview

-in�touch 2 overview�� 4

-in�touch 2 dimensions �� 4

Installation and connections

-in�touch 2-CO (spa) installation �� 5

-Connection of the in�touch 2-CO (spa) �� 6

-in�touch 2-EN (home) installation �� 7

-Connection of the in�touch 2-EN (home) �� 7

Start up

-Pairing in�touch 2-CO (spa) and in�touch 2-EN (home) �� 8

LED Status �� 9

Application�� 10

-Download application �� 10

-Using the app �� 10

-Setup your Wi-Fi on your iOS device �� 11

-Start the in�touch 2 application �� 12

-Select a spa �� 13

-Home page�� 13

-Spa state �� 14

-Water Care�� 15

-Modifying schedules�� 16

-Settings�� 17

-Wi-Fi �� 17

-in�touch network �� 18

-Change channel �� 18

-Tips �� 19

-Temperature units �� 19

-About�� 20

-Name �� 20

Troubleshooting �� 21

-in�touch 2-EN (home) status LED �� 21

-in�touch 2-CO (spa) status LED �� 22

Specifications �� 23

Table of contents

WARNING:

Before installing or connecting the unit, please read the following�

* FOR OPTIMUM PERFORMANCE PLEASE CAREFULLY READ THE MANUAL BEFORE INSTALLATION�

* INSTALL THE IN�TOUCH 2-CO MODULE AT LEAST 12" (30 CM) AWAY FROM ANY METAL PART OR ANY METAL FOIL�

* THE IN�TOUCH 2-CO MODULE SHOULD BE INSTALLED SUCH AS IT CAN BE RELOCATED UNDER THE SPA IN ORDER

TO OBTAIN OPTIMAL RECEPTION AFTER FINAL INSTALLATION OF THE SPA IN THE YARD�

* TO SATISFY FCC RF EXPOSURE REQUIREMENTS FOR MOBILE AND BASE STATION TRANSMISSION DEVICES,

A SEPARATION DISTANCE OF 8" (20 CM) OR MORE SHOULD BE MAINTAINED BETWEEN THE IN�TOUCH 2

MODULES AND PERSONS DURING OPERATION; TO ENSURE COMPLIANCE, OPERATION AT CLOSER THAN THIS

DISTANCE IS NOT RECOMMENDED�

* THE ANTENNAS USED FOR THESE MODULES MUST NOT BE CO-LOCATED OR OPERATING IN CONJUNCTION WITH

ANY OTHER ANTENNA OR TRANSMITTER�

* TO POWER THE IN�TOUCH 2-EN, ONLY USE THE POWER SUPPLY UNIT PROVIDED WITH THE IN�TOUCH 2-EN�

* THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING CHILDREN) WITH REDUCED PHYSICAL,

SENSORY OR MENTAL CAPABILITIES, OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN

SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE BY A PERSON RESPONSIBLE FOR THEIR

SAFETY�

* CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY DO NOT PLAY WITH THE APPLIANCE�

DISPOSAL OF THE PRODUCT

THE APPLIANCE (OR THE PRODUCT) MUST BE DISPOSED OF SEPARATELY

IN ACCORDANCE WITH THE LOCAL WASTE DISPOSAL LEGISLATION IN FORCE�

COMPATIBILITY REQUIREMENTS

in.touch 2 modules for FCC (North America) models (915 MHz):

Home and spa transmitter kit: 0608-521020, 0608-521023

in.touch 2 modules for ETSI (Europe) models (868 MHz):

Home and spa transmitter kit: 0608-521021, 0608-521024

Compatible spa packs:

in�xm2, in�xe, in�ye, in�yj and in�yt spa systems manufactured in or after 2012�

in.touch 2 application:

Compatible with devices running:

iOS 8�0 or higher

ROUTER AND INSTALLATION REQUIREMENTS

Any standard router with an available 100 Mbps (wired LAN) RJ45 port can be used� The router must also have its Port 10022

open, which is normally a default setting� A 3-foot (0�9 m) Ethernet cable is included�

The home transmitter will need a main supply (120V in North America, 220V in Europe) nearby to allow connection of the

transformer�

Aeware®, Gecko®, and their respective logos are Registered Trademarks of Gecko Alliance Group�

in�touch 2™, in�xm2™, in�xe™, in�yt™, in�ye™, in�therm™ and their respective logos are Trademarks of Gecko Alliance Group�

All other product or company names that may be mentioned in this publication are tradenames,

trademarks or Registered Trademarks of their respective owners�

Warning

Introduction

in�touch 2

Easily integrate your spa

to the Internet of Things!

Simplest of setups

in�touch 2 eliminates all the complexities of connecting

your spa to the Internet and transforms your smartphone

or tablet into your ultimate Wi-Fi spa remote control�

in�touch 2 comes with a state-of-the-art app and 2 pre-

paired radio frequency transmitters, one being part of

your spa system and the second one being connected

to your Internet router� Both RF transmitters are pre-

linked to one another, enabling an immediate and perfect

communication between you and your spa�

Strong and long range communication signal

Through their proprietary RF technology, in�touch 2

transceivers emit a strong, stable and long range signal

between your spa and your router (about 3 times longer

than regular Wi-Fi signal)� No need for repeaters or

boosters: your spa will always remain within reach in

typical backyard settings�

State-of-the-art app with push notifications

in�touch 2 streamlined application makes it very easy

to control and program all the functions and features of

your spa from your smartphone or your tablet� Even when

you’re away from home, you get full control of your water

care settings, filtration cycles, water temperature, economy

modes and a lot more� Push notifications will always keep

you informed on the status of your spa, even when your

app is not open�

Overview

in.touch 2 overview

in.touch 2 dimensions

3.24 in.

(82 mm)

2.94 in.

(75 mm)

.96 in.

(24 mm)

2.76 in.

(70 mm)

2.76 in.

(70 mm)

3.39 in.

(86 mm)

3.1 in.

(76 mm)

.91 in.

(23 mm)

CO Module (spa)EN Module (home)

Status LED

Pairing activation

Fastening bracket

RJ45 Ethernet connection CO pack connectionMicro USB power

EN Module (home) CO Module (spa)

Status LED

Installation and connections

in.touch 2-CO (spa) installation

Before proceeding with any installation, be sure to turn spa power off�

The in�touch 2-CO unit must be installed under the spa skirt, at least 12” (30 cm) away from any metal component or

structure� This is necessary to ensure optimal transmission� In some cases, it may be necessary to relocate the unit once

the spa is installed in the yard to ensure proper signal transmission and distance�

Install the in�touch 2-CO so the module can be repositioned to optimize the signal strength in the yard (it is possible to

see the signal strength with the in�touch 2 application in the menu Setting -> in�touch network -> Signal strength)�

We recommend that you install the unit with a #8 pan head screw�

Here are some suggestions for a successful installation:

• Install the unit as high as possible within the spa skirt, but keep it away from the spa frame if it is metallic�

• Route the cable and leave some slack in the in�touch 2-CO cable so the in�touch 2-CO can be moved around in case

of reception problems�

• Install the in�touch 2-CO in a corner of the spa to help avoid metallic components, accessories and piping close to the

in�touch 2-CO�

• The in�touch 2-CO module should be installed as close as possible to the house to optimize signal strength� It is

recommended to install the in�touch 2 module on the side of the spa facing the house to increase the signal� A body of

water between the in�touch 2-CO module and the in�touch 2-EN will reduce the signal strength�

Connection of the in.touch 2-CO (spa)

Simply connect the in�touch 2-CO module into an available CO port of the spa pack (or any other accessory with a free

CO port, such as the in�stream 2 audio amplifier, or the in�clear spa sanitizing system)�

Note that the in�touch 2-CO only has a single CO cable and thus must be installed at the end of the CO chain if more

than a single accessory is installed on the same CO port of the spa pack�

Note: Before powering up the spa pack again, please go to the next step and install the in�touch2-EN module�

Installation and connections

CO port

Installation and connections

Connection of the in.touch 2-EN (home)

Simply connect Ethernet cable into the RJ45 port of the in�touch 2-EN module and in one of the available LAN ports on

the router�

Finally, to power up the in�touch 2-EN, connect the provided transformer to a 120V (North American model) or 220V

(European model) household supply and connect the USB cable between the transformer and the in�touch 2-EN�

RJ45 Ethernet connection

LAN port, routerEthernet cableMicro usb power

in.touch 2-EN (home) installation

The in�touch 2-EN unit must be installed inside the house near the router as it needs to be connected to it� The in�touch

2-EN is provided with an Ethernet cable and a power supply� If required, a longer cable of good quality can be used by

the installer (longer cable not provided) to install the in�touch 2-EN module closer to the spa within the home� The only

requirement for installation location is that household current be available to power the in�touch 2-EN module using the

provided wall transformer�

The in�touch 2-EN can be fixed in the house to optimize the signal strength� We recommend that you install the unit with

a #8 pan head screw�

Here are some suggestions for a successful installation:

• If possible, install device on the first floor of your house�

• If installing in a basement, place at highest level possible and closest to a window�

• Try to install as far as possible from materials that may interfer with signal (ie� metal structures, thick cement walls)�

Start up

Pairing in.touch 2-CO (spa) and in.touch 2-EN (home)

The pairing process is used when you need to replace one module of the in�touch 2 kit� Otherwise, the in�touch 2 arrives

pre-paired from the factory�

1� Power up the in�touch 2-EN module

pairing button

status LED

3� Shut off the spa’s breaker (thus turning off the

in�touch 2-CO module), wait a few seconds, and

then ﬂip the breaker back on� Within a few seconds,

the pairing operation should complete and the

in�touch 2-EN status LED will no longer be YELLOW�

Main electrical box GFCI panel

Note: in�touch 2 modules can be paired as often as necessary, but can only be paired with a single counterpart module

at a time� Once paired, the modules store this information permanently until the next pairing operation� Pairing informa-

tion is stored in non-volatile memory, so pairing is not required after a power failure� Only an in�touch 2-EN module can

initiate a pairing, so it is important that the pairing begin with putting the in�touch 2-EN module in pairing mode�

If several spas are powered up at the same time with an in�touch 2-EN module in pairing mode (for instance, in a dealer

showroom), only the 1st spa to successfully connect to the in�touch 2-EN will pair� As this can be random, it is recom-

mended that only 1 spa be powered up at a time during the pairing process�

2� Press on the pairing button with a paper clip or some

similar tool� When the pairing mode is active the status

LED ﬂashes YELLOW in a rapid pattern� The in�touch

2-EN is then in pairing mode and will remain in this

mode until it pairs with an in�touch 2-CO module,

or until it is reset (power cycled)�

LED Status

LED

Each in�touch 2 module has a status LED that can be used for troubleshooting purposes�

The LED is located on the top of both enclosures�

status LED status LED

* When the LED status is blinking (blue, green or red) this

indicates that the communication between the EN module and

the CO module it not established.

EN Module (home)

Pairing mode Yellow (Blinking)

Router not detected Red

Router detected Green

in�touch 2 server detected

Module is fully functional Blue

CO Module (spa)

Pairing mode Yellow (Blinking)

Spa controller not detected Red

in�touch 2 server detected

Module is fully functional Blue

Tabla de contenidos

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación

TechBook in.touch 2 Manual de usuario

Manuales populares de Mando a distancia de otras marcas