TEA TURTLE 801589 Manual de usuario

PROFESSIONAL AIR MONITORING SYSTEMS

TURTLE

COD. 801589

PM10 - PM2,5 - TEMPERATURE- HUMIDITY

USER’S MANUAL

Ed. 19102022 v.2.0

www.tea-group.it

Table of Contents

• 1. INTENDED PURPOSE, 2. CLASSIFICATION OF EQUIPMENT, 3 . WARNINGS..............................................2

• 4. CONTENTS OF THE BOX …………………………………………………………..…………….………………….…………………..3

• 5. INSTRUCTIONS FOR PLACEMENT AND SETUP .....................................................................................4

• 6. INSTRUCTIONS FOR INSTALLATION AND STARTING............................................................................5

• 7. TECHNICAL SPECIFICATIONS, 8. MAINTENANCE, 9. GUARANTEE .......................................................6

• 10. OPTIONAL PARTS..............................................................................................................................7

www.tea-group.it

1. Intended Purpose

2. Classicaon of Equipment

ABS Enclosure (Protecon of Harmful Ingress of Water) IP44 Classicaon (outdoor use)

Oponal Power Supply (as backup to photovoltaic panel) IP20 Classicaon (indoor use)

Mode of Operaon Connuous

3. Warnings

General Warnings

CAUTION: To avoid the risk of electric shock.

CAUTION: No modicaon of this equipment is allowed.

CAUTION: Do not restrict the air ow of the product.

CAUTION: Not to be used by persons (including children) with reduced physical, sensory or mental capabilies, or lack of ex-

perience and knowledge, unless they have been given supervision or instrucon.

Children should be supervised to ensure that they do not play with the appliance.

CAUTION: Avoid deploying the device in a soot environment, with excessive dust parcles or high humidity.

CAUTION: The module should avoid contact with organic solvents (including silica gel and other adhesives), coangs,

pharmaceucals, oils and high-concentraon gases.

CAUTION: The module cannot be used in the environment containing corrosive gas for a long me. Corrosive gas will

damage the sensor.

CAUTION: Do not use this module in systems involving personal safety.

The Turtle Staon is an outdoor air quality sensor unit. It was developed to be a robust and safe device for meas-

uring air quality and detecon of ne parculate maer. Collected data is sent via WiFi into the residenal home

network and transmied through the internet to the main servers. The Turtle Monitoring Staon was developed

in collaboraon with the naonal research council of Italy.

Please read and follow all instrucons in this manual with great care.

Turtle Staon

4. Contents of the box

-open and unpack with care

-check contents for transport damages

-read the whole manual before starng sensor

801589

QR code with link to onboarding guide

Oponal Charger

www.tea-group.it

Items shown here may dier from the original provided in this package. Due to the producon process the

appearance and colors of images in the manual may dier within reasonable boundaries from the original .

Thank you for purchasing a TEA product!

To see the guide for onboarding and the

digital version of the user‘s manual,

please scan the QR code or use the link:

TURTLE

5. Instrucons for placement and setup

Keep away from any direct source of smoke, dust, heat and water.

Install on a level surface that is stable and where there is no risk of the sensor being pushed over. Do not place it on

so materials and make sure the boom airow is never blocked.

Make sure the solar panel is well illuminated by sunlight during the day and faces the direcon of the sun. You can

nd guidance on the internet about which is the best direcon (depending on your geolocaon and me of the

year) to face any solar panel to get the maximum amount of sun hours covered during the day.

Clean the glass surface of the photovoltaic solar panel with a so damp cloth every month or if you noce any dirt

on it. Handle the panel with care and make sure to not leave any scratches.

Do not expose the sensor to risk and place it stable Do not put it directly on plants or the airow gets blocked

www.tea-group.it

Turtle overview and controls on boom side :

1) Control panel (see details on right) A) Power switch (ON-OFF)

2) Plug connector for power supply (oponal) B) 4 Status LEDs (see table below)

3) Temperature sensor C) Push-buon (to get Provisioning)

4) Air intake for AQ sensor D) Orientaon Legend

5) Air ouake

6) Oponal mounng arm sockets

7) Sensor label with idencaon serial

START

1. Switch the Power switch to ON. (make sure sensor is fully charged by sun or power supply)

2. Onboard Turtle and set up the WiFi connecon (Use provided link or QR code)

*To Provision the sensor press and hold the buon “P” and switch the Power switch to ON.

6. Instrucons for Installaon and starng

LED Status Table. Error codes and Flashing paerns explanaons

1. LED L1 is on when charging with the external power supply.

2. LED L2 + L3 + L4 will ash synchronously (2 ashes per sec), during the rst start-up, with the sensor not congured.

3. Aer conguraon LED L2 + L3 + L4 will ash synchronously (1 ash per second for a short me) during boot phase.

Then only LED L2 will ash (1 ash every 5 seconds) and the LED L3 & L4 will remain o.

4. Approximately every 15 minutes LED L3 will ash with LED L2 at L1 ash per second, indicang sensor data acquision.

5. Every 24 hours, LED L4 will ash with LED L2, about one ash per second , indicang GPS data acquision.

6. In some cases the acquision of GPS data may coincide with the acquision of sensor data, in this case we will see:

LED L2 + L3 + L4 ash synchronously at one ash per second.

7. In the fail condion, L2 will ash, about 5 ashes per second, the status of L3 or L4 is irrelevant to the signal.

www.tea-group.it

LED 2 LED 3 LED 4 ashing per second Time laps STATUS soluon

yes NO NO 5x per second innity FAIL condion Restart

yes yes yes 2x per second Unl APP “ON”In provisioning Wait...

yes yes yes 1x per second 15-30 sec In acquision Wait...

yes NO NO 1x per 5 seconds 15 min working /

7. Technical specicaons

Power Requirements: Solar panel included

Internal lead acid baery (Oponal: a backup charger with Input: 100/240V ~ 50/60Hz 0,85A

Output 6,0 V = 2,4A 14,4 W IP20

SENSORS Type Units Range#1 Resoluon#3 Accuracy#4

Parcles PM10#5 Opcal parcle counter µg/m3 0-1000 µg/m3 1.0 10%

Parcles PM2.5#5 Opcal parcle counter µg/m3 0-1000 µg/m3 1.0 10%

Air temperature Solid state °C -20 / + 70 0.3 5%

Air humidity Solid state % 0 – 100 1.0 5%

Enclosure Environmental Mounng Size & weight

ABS, protecon IP44 Temperature range: -20°C to +70°C

Humidity range: 0 to 100% RH Tested

Outdoor Mounng: Length: 210 mm

Height: 220mm

Weight: 3,4kg

Mount: 350mm x 120

mm x 0,4 Kg

Communicaons Measurement period Transmission frequency Server soware Data access

Raw data sent to re-

mote server via WiFi

Connecon

30 seconds 15 minutes Web browser based,

processing of sensor

output to give reading,

database storage on

secure server

Tables, graphs, data

download, mul-user

access, oponal API

data access

9. Guarantee

Turtle staons were tested in extreme environment and harsh condions and resulted to be a robust and reliable

outdoor sensor unit. The sensor requires periodical maintenance, periodical recalibraon and periodical cleaning

procedure is suggested.

Clean the glass surface of the photovoltaic solar panel with a so damp cloth every month or if you noce any dirt

on it. Handle the panel with care and make sure to not leave any scratches.

For calibraon procedures it is necessary to use a cered laboratory. Standard maintenance and cleaning proce-

dures can be operated by the users.

Never open or manipulate the device, it will render the guarantee void and is dangerous.

The Turtle sensor device is covered by legal guarantee as described in the European direcve (EU) 2019/771

DIRECTIVE (EU) 2019/771 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL

www.tea-group.it

8. Maintenance

MOUNTING TURTLE ON VERTICAL POLE

10. Oponal parts

External baery charger for Turtle Input: 100/240V ~ 50/60Hz 0,85A

Output 6,0 V = 2,4A 14,4 W IP20 ; Wire 3500 mm .

(To order: choose plug and relave code)

802066-1 Eur

802066-3 UK

802066-2 US

8 ØMOUNTING TURTLE ON THE WALL

1. DRILL HOLES WITH THE PACKAGING

CARDBOARD TEMPLATE

2. ASSEMBLE TURTLE ON METAL BRAKET

1. TIGHTEN METAL BRAKET TO VERTICAL POLE

2. ASSEMBLE TURTLE ON METAL BRAKET

ORIENTATION

HEX SCREW

MAX DIAMETER Ø55mm

801070 METAL MOUNT ARM WITH ACCESSORIES

TOOLS REQUIRED

use level

www.tea-group.it

1. LOOSEN HEX SCREW

2. ORIENT TOWARDS THE

MAJOR SUNLIGHT SOURCE

3. TIGHTEN HEX SCREW

Oponal support mount and xture accessories

for on wall or on pole installaon instead of

regular stand-alone installaon on at surface.

Ø 5mm

Tabla de contenidos

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario