TE Connectivity HT11K Manual de usuario

Operating Instructions

HT11K Hand Tool MCON050, 0.13 – 0.35 mm²

Customer Manual No.: 411-18539-1 Rev.B

Customer Manual PN: 6-744015-4

Language: EN (translation of the German original version)

HT11K Hand Tool MCON050, 0.13

–

0.35 mm²

Page 2 - 7 Operating Instructions

411-18539-1 Rev.B

Contents

Revision history.......................................................................................................3

Introduction .............................................................................................................3

2.1

About these operating instructions.........................................................................................................3

2.2

Intended use...........................................................................................................................................3

Description...............................................................................................................4

Operation .................................................................................................................4

4.1

Crimping terminals .................................................................................................................................4

Customer Service, EMEA Service Hotline.............................................................7

Maintenance and servicing.....................................................................................7

6.1

Daily maintenance..................................................................................................................................7

6.2

Periodic inspection.................................................................................................................................7

HT11K Hand Tool MCON050, 0.13

–

0.35 mm²

Page 3 - 7 Operating Instructions

411-18539-1 Rev.B

1 Revision history

Rev. Date Description Name

A 12.02.2015 First version Christian Witt

B 06.08.2015 Revision Levin Sandhu

Tab. 1 : Revision history

2 Introduction

2.1 About these operating instructions

These operating instructions describe the use and operation of the HT11K hand tool and the

necessary maintenance measures. All persons using the hand tool must therefore be familiar

with these operating instructions and follow them. It should be stressed that the operating in-

structions for the HT11K hand tool are essential.

These operating instructions must be available with the hand tool at all times. The tool owner

and/or user is obliged to supplement these operating instructions with instructions in line with

existing national regulations for the prevention of accidents and environmental protection.

These operating instructions apply to the following hand tool from TE Connectivity:

HT11K Hand Tool MCON050 0.13-0.35 mm²: TE PN 4-1579014-1

2.2 Intended use

The hand tool was developed to crimp MCON050 terminals according to the TE processing

specification and drawing. The hand tool may only be used for repair purposes or for making

samples, not for series production. The following terminals can be processed with the hand tool:

Terminal PN Cross-section Terminal TE processing specification

2177908 0.13 / 0.17 mm²

MCON050 Appl. Spec. 114-94191

TE PN 4-1579014-1

2177909 0.22 / 0.22 (RF*) /

0.35 (FLR) /

0.35 mm² (FLU) MCON050 Appl. Spec. 114-94191

TE PN 4-1579014-1

Tab. 2 : Processable terminals

RF* = Reinforced

HT11K Hand Tool MCON050, 0.13

–

0.35 mm²

Page 4 - 7 Operating Instructions

411-18539-1 Rev.B

3 Description

The hand tool essentially consists of a crimping head, two moveable handles, a ratchet mecha-

nism, a sliding crimping die, a die latch, a hinged terminal holder and a hinged wire stop. The

sliding crimping die contains six marked crimping nests.

Abb. 1 : The hand tool, front (left), rear (right)

Item Description Item Description

1 Crimping head 2 Handles

3 Locking mechanism 4 Crimping die

5 Crimping nest 6 Die latch

7 Wire stop 8 Terminal holder

Tab. 3 : Components of the hand tool

4 Operation

4.1 Crimping terminals

Based on the wire cross-section and the relevant processing specification, determine the right

crimping die for the terminal to be processed. Proceed as follows to crimp the terminal:

Close the hand tool until the locking mechanism allows you to open the handles.

HT11K Hand Tool MCON050, 0.13

–

0.35 mm²

Page 5 - 7 Operating Instructions

411-18539-1 Rev.B

Abb. 2 : Position the die

Lift the die latch and position the die, so that the cross-section to be processed can be seen

in the viewing window.

The die latch must then be returned to the starting point, so that the die is fixed in position.

Open the hinged terminal holder.

Open the wire stop and insert the terminal to be processed into the terminal holder. Make

sure the terminal is pushed into the stop in the terminal holder.

Abb. 3 : Position the terminal over the terminal holder (left), insert wire (right).

NOTE

The locking mechanism of the hand tool has a ratchet that makes audible clicks when

you close the handles. hen you hear the last click, the locking mechanism releases

and the hand tool can be opened again. For an emergency release, the lever of the un-

locking mechanism must be operated.

Viewing window

ire stop

HT11K Hand Tool MCON

050, 0.13

–

0.35 mm²

Page 6 - 7 Operating Instructions

411-18539-1 Rev.B

Carefully close the hinged terminal holder.

Feed the wire, insulated according to the processing specification, into the terminal until it

reaches the wire stop.

Hold the wire against the wire stop and press the handles together until the locking mecha-

nism opens again. The hand tool then opens fully.

Abb. 4 : Crimp terminal (left), check the crimped terminal

(right)

Then you can remove the crimped terminal from the crimping die. Ensure that the wire stop

is opened. If the terminal is stuck, jiggle it slightly to remove it from the terminal holder.

Check the crimp height of the crimped terminal, based on the information in the TE Con-

nectivity processing specification and the drawing.

HT11K Hand Tool MCON050, 0.13

–

0.35 mm²

Page 7 - 7 Operating Instructions

411-18539-1 Rev.B

5 Customer Service, EMEA Service Hotline

Please contact us for service enquiries or technical support:

Monday - Thursday 8am - 4pm

Friday 8am - 2pm

Tel. +49 (0) 6151 607 -1518

www TEFE1@TE.COM (EMEA Customer Support)

www TEFE2@TE.COM (EMEA Hand Tool Repair)

_____________________________________________

TE Connectivity Germany GmbH

c/o Schenck Technologie- und Industriepark GmbH

Landwehrstr. 55 / Gebäude 83

64293 Darmstadt

Germany

Additional information and contact details can also be found online.

Visit us at: http://tooling.te.com/

6 Maintenance and servicing

6.1 Daily maintenance

The following daily maintenance tasks should be performed by the responsible operator:

Using a soft, clean brush or a lint-free cloth, remove dirt, dust, moisture and other residue

from the hand tool. Do not use any hard or abrasive tools or materials that could damage

the hand tool.

Apply sewing-machine oil to all pivot points and bearing surfaces. Do not lubricate exces-

sively.

When the hand tool is not needed, store it in a clean and dry location.

6.2 Periodic inspection

The hand tool should be inspected periodically by suitably qualified staff according to the

level of use, and the inspections should be documented.

Check the hand tool for wear and damage, particularly in the crimping nest areas.

Otros manuales para HT11K

Tabla de contenidos

Otros manuales de Herramientas de TE Connectivity

TE Connectivity

TE Connectivity 2255140-1 Manual de usuario

TE Connectivity

TE Connectivity 2255143-1 Manual de usuario

TE Connectivity

TE Connectivity 354711-1 Manual de usuario

TE Connectivity

TE Connectivity PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2215038-1 Manual de usuario

TE Connectivity

TE Connectivity 1725062-1 Manual de usuario

TE Connectivity

TE Connectivity 58372- 1 Manual de usuario

TE Connectivity

TE Connectivity 768338-2 Manual de usuario

TE Connectivity

TE Connectivity OCEAN 2.0 Manual de usuario

TE Connectivity

TE Connectivity CERTI-CRIMP II Guía de referencia

TE Connectivity

TE Connectivity TERMI-POINT 59865-1 Guía de referencia

TE Connectivity

TE Connectivity 58024-1 Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity Ocean 1.0 Manual de usuario

TE Connectivity

TE Connectivity CXP 2018681-1 Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity 2379255-1 Manual de usuario

TE Connectivity

TE Connectivity 90331- 1 Manual de usuario

TE Connectivity

TE Connectivity 2430769-1 Manual de usuario

TE Connectivity

TE Connectivity CERTI- LOK Hand Tool Frame Assembly 169400 Manual de usuario

TE Connectivity

TE Connectivity 734185-1 Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 6-1579014-1 Manual de usuario

Manuales populares de Herramientas de otras marcas

Martor

Martor SECUNORM 175 Manual de usuario

ERKCO

ERKCO 1000 Manual de usuario

jbc

jbc N4473 Manual de usuario

FEINMETALL

FEINMETALL FZWZ-SET-001 Manual de usuario

Worx Professional

Worx Professional Sonicrafter WU676 Manual de usuario

Gage Bilt

Gage Bilt GB713SH Manual de usuario

Hilti

Hilti DX 9-ENP Manual de usuario

norbar

norbar NORTRONIC 34399 Manual de usuario

BGS technic

BGS technic 8578 Manual de usuario

Makita

Makita DHR241 Manual de usuario

Motor Guard

Motor Guard JMB-1250 Manual de usuario

Power Adhesives

Power Adhesives 805-12 Manual de usuario

Clemco

Clemco 24189 Manual de usuario

VVG

VVG VNG 903 Series Manual de usuario

Hilti

Hilti FX 3-A Manual de usuario

Grizzly

Grizzly H6472 Manual de usuario

axing

axing BWZ 5-02 Manual de usuario

Dh-Robotics

Dh-Robotics RGI-100 Cómo utilizar