TE Connectivity 46447 Manual de usuario

Instruction Sheet

1 of 11

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

408-1542

13 JUL 2021 Rev U

PROPER USE GUIDELINES

Cumulative trauma disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional

use and low-volume applications. A wide selection of powered application equipment is available for extended-use production operations.

Figure 1: Hand crimping tools

One crimping chamber (typical)

Two crimping chambers (typical)

Three crimping chambers (typical)

Wire size marking

CERTI-CRIMP™tool ratchet

1. INTRODUCTION

Hand Crimping Tools 46447, 2326374-1, 47410 (crimps 12-10 AWG terminals on a 45° angle), 49592, 49935,

69363, 525693, 574573, 1490046-1, and 1490047-1 (shown in Figure 1) are used to crimp SOLISTRAND™

and STRATO-THERM™terminals and splices (listed in Table 1) onto stranded wire sizes 26 through 10 AWG.

Read these instructions thoroughly before using the tool.

NOTE

Dimensions in this instruction sheet are in millimeters with [inches in brackets]. Figures are for reference only and are not

drawn to scale.

Reasons for reissue of this instruction sheet are provided in Section 7, REVISION SUMMARY.

Hand Crimping Tools 46447, 2326374-1,

47410, 49592, 49935, 69363, 525693,

574573, 1490046-1 and 1490047-1

408-1542

Rev U

2 of 11

Table 1: Specifications

Product

Hand tool

Wire size

(AWG) range

and terminal

size

Crimping

chamber

marking

Wire strip length

Terminal

(standard)

Terminal

(long barrel)

Butt

splice

Parallel

splice

STRATO-THERM

46447

2326374-1

22-16

4.37-5.16

[.172-.203]

---

6.35-7.14

[.250-.281]

7.94-8.73

[.313-.344]

16-14

12-10

6.35-7.14

[.250-.281]

SOLISTRAND

49592

14-12

4.37-5.16

[.172-.203]

---

7.94-8.73

[.313-.344]

---

49935

525693

574573

22-16

4.37-5.16

[.172-.203]

6.35-7.14

[.250-.281]

6.35-7.14

[.250-.281]

7.94-8.73

[.313-.344]

49935

525693

574573

1490046-1

16-14

4.37-5.16

[.172-.203]

6.35-7.14

[.250-.281]

6.35-7.14

[.250-.281]

7.94-8.73

[.313-.344]

47410

49935

525693

574573

1490047-1

12-10 &

16-14 HD

12-10

6.35-7.14

[.250-.281]

---

6.35-7.14

[.250-.281]

---

69363

26-24

3.17-3.97

[.125-.156]

---

3.57-4.37

[.141-.172]

---

22-20

4.37-5.16

[.172-.203]

---

5.16-5.95

[.203-.234]

---

24-20

22-20

---

4.37-5.16

[.172-.203]

---

26-22

26-24

3.17-3.97

[.125-.156]

---

3.57-4.37

[.141-.172]

---

2. DESCRIPTION

Each tool consists of a CERTI-CRIMP tool ratchet and two crimping jaws (indenter and anvil) containing one,

two, or three crimping chambers. Each tool is marked with the wire size range for each crimping chamber

(Figure 1). Full crimping of the terminal or splice is assured by the CERTI-CRIMP tool ratchet. When engaged,

the ratchet does not release until the tool handles have been fully closed.

CAUTION

The crimping jaws bottom before the ratchet releases. This feature ensures maximum electrical and tensile performance of

the crimp. Do not re-adjust the ratchet.

3. CRIMPING

1. Strip the wire according to the dimensions listed in Table 1. The strip length is determined by the type

of terminal or splice and by the wire size. Do not nick or cut the wire strands.

2. Close the tool handles until the ratchet releases.

3. Allow the tool handles to open fully.

408-1542

Rev U

3 of 11

4. Center the terminal or splice wire barrel in the appropriate crimping chamber (Figure 2).

For terminals, make sure that the flat side of the tongue faces the anvil or the nest.

For splices, make sure that the brazed seam (when visible) is toward the indenter or the nest.

Figure 2: Centering the wire barrel in the crimping chamber

Terminal

Wire barrel centered in crimping chamber

Parallel splice

Flat side of terminal tongue facing anvil

Butt splice

Brazed seam on splice toward indenter

NOTE

Terminals and splices can also be rotated 180 degrees with the seam toward the nest.

5. While holding the terminal or splice in place, squeeze the tool handles together just until the jaws begin

to close on the wire barrel. Do not deform the wire barrel.

6. Insert the stripped wire into the wire barrel, making sure that the wire insulation does not enter the wire

barrel (Figure 3).

Figure 3: Inserting stripped wire in wire barrel (not to scale)

Terminal

Wire strip length

Parallel splice

Wire barrel

Butt splice

Strap type

7. While holding the wire in place, squeeze the tool handles together until the ratchet releases, then allow

the tool handles to open fully.

8. To crimp the other half of a butt splice, position the uncrimped wire barrel in the crimping chamber and

repeat the crimping procedure.

NOTE

If the splice cannot be turned for crimping the other half, turn the tool around.

408-1542

Rev U

4 of 11

4. INSPECTING THE CRIMP

Inspect crimped terminals and splices by checking the features shown in Figure 4. Poor crimps (Figure 5) can

be avoided by carefully following the procedures provided in Section 3, and by following the tool maintenance

procedures provided in Section 5.

Figure 4: Features of a good crimp

Terminal

Parallel splice

Butt splice (strap type)

Butt splice (sight hole or stranded type)

Wire insulation does not enter wire barrel

Crimp is centered. Crimp can be off center, but not off end of wire barrel.

Wire is visible through inspection hole. Wire is flush with or extends

slightly beyond end of wire barrel.

Wire size matches wire range or size stamped under tongue.

Bare wire ends are flush with or extend slightly beyond end of wire barrel.

Wire size matches wire range or size stamped on splice.

Figure 5: Features of a poor crimp

Terminal

Parallel splice

Butt splice (strap type)

Butt splice (sight hole or stranded type)

Crimped off end of wire barrel

Wire not inserted far enough. End of wire must be visible through inspection

hole, and be flush with (or extend slightly beyond) end of wire barrel.

Nicked or missing strands

Wire size does not match wire range or size stamped under tongue.

Wire insulation enters wire barrel. Check for incorrect strip length.

Excess “flash” on terminal or splice indicates damaged jaws or use of wrong

wire, splice, or tooling combination.

Wire size does not match wire range or size stamped on splice.

408-1542

Rev U

5 of 11

5. MAINTENANCE AND INSPECTION

The tool is inspected before being shipped. Inspect it immediately upon arrival at your facility to ensure that the

tool has not been damaged during shipment.

Frequency of inspection depends on:

The care, amount of use, and handling of the hand tool

The presence of abnormal amounts of dust and dirt

The degree of operator skill

Your own established standards

5.1. Daily maintenance

Remove dust, moisture, and other contaminants with a clean soft brush or soft lint-free cloth. Do not

use objects that could damage the dies or tool.

Make certain that the retaining pins are in place and that they are secured with retaining rings.

All pins, pivot points, and bearing surfaces should be protected with a thin coat of any good SAE 20

motor oil. Do not oil excessively.

When the tool is not in use, keep the handles closed to prevent objects from becoming lodged in the

dies. Store the tool in a clean, dry area.

5.2. Lubrication

Lubricate all pins, pivot points, and bearing surfaces with SAE 20 motor oil as indicated in Table 2.

Table 2: Lubrication schedule

When tool is used

When to lubricate

In daily production

Daily

Daily (occasional)

Weekly

Monthly

NOTE

Wipe excess oil from the tool, particularly from the crimping area. Oil transferred from the crimping area onto certain

terminations can affect the electrical characteristics of an application.

408-1542

Rev U

6 of 11

5.3. Periodic inspection

Remove accumulated dirt, grease, and foreign matter by immersing the tool (with handles partially

closed) in a reliable commercial degreasing compound.

Close the tool handles until the ratchet releases and then allow them to open freely. If they do not open

quickly and fully, the spring is defective and must be replaced. See Section 6, REPLACEMENT AND

REPAIR.

Inspect the head assembly for worn, cracked, or broken jaws (Figure 6). If damage is evident, return

the tool to TE for evaluation and repair. See Section 6, REPLACEMENT AND REPAIR.

Figure 6: Inspecting the head assembly

Pitted

Chipped edge

Flattened area

Broken corner

408-1542

Rev U

7 of 11

5.4. Gaging the crimping chambers

This inspection requires the use of a plug gage (Figure 7) conforming to the dimensions listed in Table 3.

Figure 7: Recommended plug gage design

GO dimension

12.7 [.50] minimum (typical)

50.8 [2.00] minimum (typical)

NO-GO dimension

Jaw closure configuration

Table 3: Plug gage dimensions

Hand tool

Crimping

chamber

marking

Gage element dimensions mm [in.]

NO-GO

46447

2326374-1

22-16

1.295-1.303 [.0510-.0513]

1.445-1.447 [.0569-.0570]

1.57 [.062]

16-14

1.498-1.506 [.0590-.0593]

1.648-1.651 [.0649-.0650]

1.57 [.062]

12-10

2.108-2.116 [.0830-.0833]

2.258-2.260 [.0889-.0890]

2.36 [.093]

49592

14-12

1.752-1.760 [.0690-.0693]

1.902-1.905 [.0749-.0750]

1.57 [.062]

49935

525693

574573

22-16

1.168-1.176 [.0460-.0463]

1.318-1.320 [.0519-.0520]

1.57 [.062]

49935

525693

574573

1490046-1

16-14

1.371-1.379 [.0540-.0543]

1.521-1.524 [.0599-.060]

1.98 [.078]

47410

49935

525693

574573

1490047-1

12-10

1.930-1.938 [.0760-.0763]

2.080-2.082 [.0819-.082]

2.76 [.109]

69363

26-24

0.660-0.668 [.026-.0263]

.0810-0.812 [.0319-.032]

1.003 [.0395]

22-20

0.939-0.947 [.037-.0373]

1.089-1.092 [.0429-.043]

1.19 [.047]

408-1542

Rev U

8 of 11

TE does not manufacture or market these gages. To gage the crimping chambers, proceed as follows:

1. Remove traces of oil or dirt from the crimping chambers and plug gage.

2. Close the tool handles until it is evident that the jaws have bottomed; then hold in this position. Do not

force the jaws beyond initial contact.

3. Align the GO element with the crimping chamber. Push element straight into the crimping chamber

without using force. The GO element must pass completely through the crimping chamber (Figure 8).

4. Align the NO-GO element and try to insert it straight into the same crimping chamber. The NO-GO

element can enter partially, but must not pass completely through the crimping chamber (Figure 8).

Figure 8: Gaging with GO and NO-GO elements

Crimping chamber

GO element

NO-GO element

NOTE

The jaws in Tools 49935 and 574573 are not symmetrically located. Make sure that the tool conforms to the symmetry

requirements shown in Figure 9.

Figure 9: Symmetry requirements for tools 49935, 574573, 1490046-1, and 1490047-1

Jaws

0.254 mm [.010 in.] minimum (typical)

If the crimping chambers conform to the gage inspection, the tool is considered dimensionally correct.

Lubricate it with a thin coat of any good SAE 20 motor oil.

If not, the tool must be returned for further evaluation and repair. Refer to Section 6, REPLACEMENT

AND REPAIR.

For additional information regarding the use of a plug gage, refer to Instruction Sheet 408-7424.

408-1542

Rev U

9 of 11

5.5. Inspecting the ratchet

1. Check the CERTI-CRIMP tool ratchet to verify that the ratchet does not release prematurely, allowing

the jaws to open before they have fully bottomed.

2. Obtain a 0.025 mm [.001 in.] shim suitable for checking the clearance between the bottoming surfaces

of the crimping jaws.

3. Select a terminal or splice, and properly stripped wire with maximum wire load (such as wire size 16

AWG and size 22-16 terminal).

4. Position the terminal or splice and wire between the crimping jaws, as described in Section 3,

CRIMPING.

5. Hold the wire in place and squeeze the handles until the CERTI-CRIMP tool ratchet releases. Hold the

handles in this position, maintaining just enough tension to keep the jaws closed.

6. Use the shim to check the clearance between the bottoming surfaces of the crimping jaws.

If the clearance is 0.025 mm [.001 in.] or less, the ratchet is satisfactory.

If clearance exceeds 0.025 mm [.001 in.], the ratchet is out of adjustment and must be repaired.

See Section 6, REPLACEMENT AND REPAIR.

408-1542

Rev U

10 of 11

6. REPLACEMENT AND REPAIR

Customer-replaceable parts are listed in Table 4. Stock and control a complete inventory to prevent lost time

when replacement of parts is necessary. Parts other than those listed should be replaced by TE to ensure

quality and reliability. Order replacement parts through your TE representative. You can also order parts by any

of the following methods:

Go to TE.com and click the Shop TE link at the top of the page.

Call 800-522-6752.

Write to:

CUSTOMER SERVICE (038-035)

TE CONNECTIVITY CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

Tools can also be returned to TE for evaluation and repair. For customer repair services, call 800-522-6752.

Figure 10: Tool dimensions (with handles closed) and replacement parts

Table 4: Replacement parts

Item

Part number

Description

Quantity per tool

525693 tool only

21045-3

Ring, retaining

---

1-23619-6

Ring, retaining

39364

Spring, hold down

---

2-23620-9

Pin, straight, grooved

21045-6

Ring, retaining

525108

Ring, retaining, beryl copper

---

Otros manuales para 46447

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas eléctricas de TE Connectivity

TE Connectivity

TE Connectivity 58536-1 Manual de usuario

TE Connectivity

TE Connectivity 2363592-1 Manual de usuario

TE Connectivity

TE Connectivity 1976330-1 Manual de usuario

TE Connectivity

TE Connectivity 539 666-2 Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity 2430768-1 Manual de usuario

TE Connectivity

TE Connectivity 2396645-1 Manual de usuario

TE Connectivity

TE Connectivity 59275 Manual de usuario

TE Connectivity

TE Connectivity 2390076-1 Manual de usuario

TE Connectivity

TE Connectivity 2844990-1 Guía de referencia

TE Connectivity

TE Connectivity 354940-1 Manual de usuario

TE Connectivity

TE Connectivity OCEAN 2.0 Manual de usuario

TE Connectivity

TE Connectivity 47386-4 Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 7-1579004-1 Manual de usuario

TE Connectivity

TE Connectivity 2390879-1 Manual de usuario

TE Connectivity

TE Connectivity 2155369 Manual de usuario

TE Connectivity

TE Connectivity MATE-AX 2335290-1 Manual de usuario

TE Connectivity

TE Connectivity CAPI-6T Manual de usuario

TE Connectivity

TE Connectivity 2389783-1 Manual de usuario

TE Connectivity

TE Connectivity 2389862-1 Manual de usuario

TE Connectivity

TE Connectivity 59239-4 Manual de usuario

TE Connectivity

TE Connectivity PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity HT40 Manual de usuario

TE Connectivity

TE Connectivity 2381114-1 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual