TE Connectivity MR-1 Manual de usuario

1 of 5

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

TOOLING ASSISTANCE CENTER

1-800-722-1111

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

Instruction Sheet

408-7306

24 NOV 14 Rev C

Figure 1

1. INTRODUCTION

Model MR-1 Hand Crimping Tool 251101-1 is designed to crimp PICABOND Connectors in through, tapping,

and bridging operations. The tool can be hand-held or it can be used in Tool Holder 251852-1 with or without

the Frame Adapter 229175-1. Read the instructions packaged with these accessories.

NOTE

All dimensions on this document are in metric units [with U.S. customary units in brackets]. Figures and illustrations are for

reference only and are not drawn to scale.

Reasons for reissue of this sheet are provided in Section 11, REVISION SUMMARY.

2. DESCRIPTION (Figure 1)

The tool features two wire supports, a set of dies (anvils and crimpers), a wire cutter, and a handle assembly.

In use, the wire supports hold and position the wires in the crimpers. As the tool is cycled, the wire cutter cuts

off excess wire, then the crimping dies crimp the connector to the wires. Continuous pressure applied to the

moving handle forces the link to snap the tool handles closed, thus completing the crimp cycle. After the cycle

is completed, depress the release lever to open the handles and remove the crimped connector.

3. CONNECTOR SELECTION

Determine the wire gage and combination of conductors to be joined. Then refer to Figure 2 for the correct

connector. Note the PICABOND connectors can be used for 28 through 19 AWG copper conductors that are

insulated with plastic, paper, or pulp materials.

WIRE RANGE (AWG)

CONNECTOR DESCRIPTION

NUMBER

COLOR

28-24

61899-1▪

Orange

26-22

60945-4▪

Green

61226-2▪

Purple

24-19

60947-3†

Red

61292-2†

Yellow

▪Use any 1 or 2 wire combination. †Only one (1) 19 AWG can be used per connector end. This can be in combination with any other wire size up to 24 AWG.

Figure 2

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low

volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

Model MR-1 Hand Crimping

Tool 251101-1 for PICABOND*

Connectors

Release Lever

Moving Handle

WD-40 is a Trademark.

Lubrication Points

■WD-40

Grease

■

Link

Color Code

Label

Wire Notch

Wire Cutter

Splitter Pin

Anvil

Fixed Handle

Support Tool Here to

Keep it from Moving

During Crimp Cycle



Wire Support

■

Crimpers

ORIGINAL INSTRUCTIONS

408-7306

Rev C

2 of 5

4. PREPARING CABLE

Open and prepare the cable in the usual manner. There is no special procedure required when using the Model

MR-1 tool.

5. WIRE PLACEMENT

NOTE

The essential difference of the various connections is the placement of the wires in the wire supports.

Determine the type of connection to be made, then refer to the applicable Paragraph (5.1, 5.2, or 5.3) and

insert the wire accordingly.

5.1. Through Connections (See Figure 3)

NOTE

Always start with the cable units to the REAR of the cable opening.

1. Take a pair of conductors from one side of the cable opening. Separate them far enough that one wire

can be inserted into the wire support.

2. Holding the tool in one hand, lace the wire into the wire support and out between the crimpers. Make

sure the wire has sufficient slack, then bottom it in the wire support.

3. Repeat Steps 1 and 2 using a pair of conductors from the other side of the cable opening. Be sure to

match tip to tip and ring to ring.

4. Insert a connector and crimp it according to Section 6, CRIMPING PROCEDURES. Join the other

conductors of the same pair in the same manner.

Figure 3

5.2. Tap Connections (See Figure 4)

The following method is accomplished without cutting and interrupting service of a through conductor. It is

especially helpful when tapping into taut wires.

1. Lace tap wire into wire support below the pin.

2. Take a pair of through conductors from the cable unit and separate them enough to insert individual

wires into the tool.

3. Place one wire into a connector and then insert the connector into the tool as shown in Figure 4. Make

sure the wire cutter enters the slots in the center of the connector and that the notch in the wire cutter

does NOT interfere with the connector.

4. Position the through wire in the notch of the wire cutter, then lace it into the wire supports above the

pin.

5. Crimp the connector according to Section 6, CRIMPING PROCEDURES.

Center Slot

Wire Support

Through Splice

Anvil

Connector

Wire Cutter

Through

Wire

Crimper

Top of Tool

Through

Wire

408-7306

Rev C

3 of 5

Figure 4

5.3. Bridging Connectors (See Figure 5)

1. Take a pair of through conductors from one side of the cable opening and separate them enough to

insert individual wires into the tool.

2. Lace the bridge wire(s) into the wire support(s) below the pin(s).

3. Lace the through wires into the wire support above the pin. Make sure you use matching wires - tip to

tip and ring to ring.

4. Insert a connector into the tool as shown in Figure 5. Make sure the wire cutter enters the slots in the

center of the connector.

NOTE

When butt splicing, insert one wire above the pin and one wire below the pin on the same side of the tool.

Figure 5

6. CRIMPING PROCEDURES

CAUTION

The tool must be held steady during the crimping procedure. If it moves before the crimp is completed, the wires may pull out

of the connector. See Figure 1.

After placing the wire(s) and connector in the tool in accordance with Section 5, WIRE PLACEMENT, proceed

as follows:

1. Make sure there is sufficient slack in the wires, otherwise, they could pull out of the connector during

the crimp cycle.

2. Place the tool in one hand so that you are supporting the center portion of the fixed handle as

indicated in Figure 1.

3. Crimp the connector by squeezing the tool handles until they snap over center.

4. Open the tool handles by depressing the release lever, and then remove the crimped connector.

Double Half-Tap

Connector

Wire Support

Through

Wire

Crimper

Top of Tool

Single Half-Tap

Wire Cutter

Notch

Tap Wire

Anvil

Center Slot

Single Bridge

Double Bridge

Butt Splice

Center Slot

Top of Tool

Crimper

Wire Support

Connector

Through Wire

Wire Cutter

Through Wire

Bridge Wire

Anvil

408-7306

Rev C

4 of 5

7. SPLICE BUILD-UP

During the splicing, you should arrange groups of finished connections along the splice opening in order to

build a uniform, compact splice. To do this, move the tool along the splice opening about 31.75 mm [1.25 in.]

after crimping every 25 to 50 pairs. Alternate the direction in which you move the tool, first to one side of center,

then to the other.

8. INSPECTIONS

Make the following inspections on the first and last connection made during a shift. If you find any improperly

crimped or defective connections, return the tool to your supervisor, unless otherwise instructed. In addition,

replace any defective connections.

8.1. Gaging Crimped Connectors

Use the crimp gage within a short time of crimping the connection, and check the connector as follows:

1. Select the proper gage end. The color dots on the end of the gage must match the color of the

connector you are gaging. See Figure 6.

2. Place the connector in the gage so the seam in the connector aligns with the double rib on the gage.

Position the connector so it is flush with the side of the gage. See Figure 6.

Figure 6

3. Hold the free end of the connector and slide the gage off using only very slight force. The gage must

slide off easily. If it does, repeat the test for the other end of the connector.

4. If either end of the connector sticks in the gage, the connection is improperly crimped. Make a few

sample crimps and gage them. If they gage properly, continue using the tool. If they do not gage

properly, return the tool for repair. In either case, go back and re-crimp any improperly crimped

connections.

Figure 7

8.2. Visual Inspection (See Figure 7)

1. Check for wire protruding from the center of the connector. If you find any, replace the connection. If

this problem occurs frequently, return the tool for adjustment.

Green or

Purple Dot

Orange Dot

Wire Size

Boss

Double Rib

Gage

Red or

Yellow Dot

Double Rib

Seam

End of Connector Flush

with Side of Gage

Boss

Two Wires on Same

Side of Seam

Protruding Wire

Cut and Score Marks

Improper Connector

Placement

408-7306

Rev C

5 of 5

2. Make certain there are no wires missing from the connector. If there is, the tool probably moved during

crimping and the connector must be replaced.

3. Check for a metal leg protruding from the center of the connector. This is caused by improper location

of the connector in the tool. If you find any, replace the connections. Be especially careful to insert the

connector in the tool so that the slot in the connector engages the wire cutter, and that the notch in the

wire cutter does NOT interfere with the connector. See Figures 3, 4, and 5.

4. If you are tapping or bridging, make sure the end of the connector with two conductors contains one

conductor on each side of the seam.

If both conductors are on the same side, replace the connection. Be very careful to place the

conductors in the wire support correctly. If the condition persists, return the tool to your supervisor.

5. Check the plastic wire support brackets. If they are damaged, or if the pins in the supports are bent or

have a rough surface, replace the supports. Use Repair Kit 229188-1 and follow the instructions in the

kit.

9. MAINTENANCE AND CLEANING

TE Connectivity recommends Cleaning Kit 229333-1 for cleaning this tool. This kit consists of: (1) a bristle

brush for general purpose cleaning, (2) a tube cleaner for cleaning the crimping dies, (3) a tube brush for

cleaning inside the tool, (4) an extractor for removing scrap wire and plastic particles from inside the crimping

dies, and (5) extractor case. If you do not have this kit, it can be purchased from TE.

NOTE

A lubricant, WD-40, which can be purchased locally, is recommended for loosening dirt and lubricating the tooling.

NOTE

A spray solvent/cleaner, which can be purchased from Orb Industries, Upland, PA (215-874-2537), under part number 590, is

recommended for removing accumulated film.

Remove all loose dirt with a clean bristle brush. Then liberally spray the tool with solvent/cleaner and allow it to

dry. Remove any particles that you have loosened. Lubricate the tool with WD-40 lubricant and all-purpose

grease. See Figure 1 for lubrication points.

As the operator of the tool, you should: (1) clean and lubricate the tool regularly, (2) inspect the crimped

connectors, and (3) use the tool in accordance with these instructions. If you find a defect in the tool's

operation, return it to your supervisor.

10. ORDERING INFORMATION AND REPAIR

Order additional tools through your TE Representative, or call 1-800-526-5142, or send a facsimile of your

purchase order to 1-717-986-7605 or write to:

CUSTOMER SERVICE (038-035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

Tools may be returned to TE for evaluation and repair. For tool repair service, please contact a TE

Representative at: 1-800-526-5136.

In Canada, send the tool to:

TE CONNECTIVITY OF CANADA (BLDG. 1)

20 ESNA PARK DRIVE

MARKHAM, ONTARIO

CANADA, L3R 1E1

ATTENTION: PICABOND TOOL REPAIR

11. REVISION SUMMARY

Updated document to corporate requirements

New logo

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

TE Connectivity Divested:

349568-9

Tabla de contenidos

Otros manuales de Herramientas de crimpado de TE Connectivity

TE Connectivity

TE Connectivity 2391789-1 Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 2-1579016-2 Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 4-1579001-1 Manual de usuario

TE Connectivity

TE Connectivity 2377672-1 Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity 90117 Manual de instrucciones

TE Connectivity

TE Connectivity 91366- 1 Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity 2391435-1 Manual de usuario

TE Connectivity

TE Connectivity 2394165-1 Manual de usuario

TE Connectivity

TE Connectivity 2407132-1 Manual de usuario

TE Connectivity

TE Connectivity 2380840-1 Manual de usuario

TE Connectivity

TE Connectivity Faston Series Manual de usuario

TE Connectivity

TE Connectivity 46447 Manual de usuario

TE Connectivity

TE Connectivity 69069 Manual de usuario

TE Connectivity

TE Connectivity PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2390409-1 Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

TE Connectivity

TE Connectivity PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity SDE-SA Manual de usuario

TE Connectivity

TE Connectivity 69339 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

molex

molex 63811-5100 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

molex

molex 63825-3000 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario