TDK-Lambda Genesys Series Manual de usuario
Series
Programmable DC Power Supplies
G1.7 - 5kW in 1U 0-600V, 0-500A
PARALLEL KIT INSTRUCTION MANUAL
The manual covers kit options:
G/P-3U-10V
G/P-3U-20-40V
G/P-3U-60-100V
G/P-3U-150-600V
2
1.1
General
Parallel kit is supplied separately from the power supply packing according to order.
The usage of parallel kit is according to customer's needs.
1.2
Advanced Parallel
For parallel connection, refer to advanced parallel chapter in the series User Manual.
1.3
Product Safety Instructions
Safety approvals are valid for single unit only. These are not valid for parallel kit assembly.
When using a paralleling kit with a protective bracket, it must be correctly assembled, as described
further in this document.
1.4
Assembly Instructions
The supplied kit is used for standard and blank panel options. Follow the instructions carefully
according to power supply model.
1.4.1
G/P-3U-10V - Assembly Instructions for three 10V units in Parallel
1.4.1.1
Components List
Image Component Quantity
10‐32x5/16PanHeadScrew,StainlessSteel 12
HelicalSpring‐LockWasher,No.10,StainlessSteel 12
PlainWasher,No.10,StainlessSteel 12
ConnectionPlate3U 2
OutputShort 2
3
Image Component Quantity
M3x4CFlatHeadScrew,NickelPlated 8
ParallelingCable 2
OutputCover 1
BusBarInsulator 2
M3x8SEMSScrew,NickelPlated 6
4
1.4.1.2
Installation Steps
1. Attach connection plates, one on each side of the power supplies, using 12 pan head screws,
12 helical spring-lock washers and 12 plain washers as illustrated in Figure 1.
Figure1:Three10VUnitsConnectionPlates3UAssembly
2. Attach output short plates, one on each triple of terminals, using eight flat head screws as
illustrated in Figure 2.
Figure2:Three10VUnitsOutputShortPlatesAssembly
ConnectionPlate
3U
PlainWasher,No.10,StainlessSteel
HelicalSpring
‐
LockWasher,No.10,StainlessSteel
10‐32x5/16PanHeadScrew,StainlessSteel
Tighteningtorque:25.4‐31.7Lbf‐inch(2.87‐3.58Nm).
M3x4CFlatHeadScrew,NickelPlated
Tighteningtorque:4.7‐5.7Lbf‐inch(0.53‐0.64Nm)
OutputShort
5
3. Connect two paralleling cables from top unit M connector to bottom unit S connector as
illustrated in Figure 3.
Figure3:Three10VUnitsParallelingCableConnection
4. Insert output cover through the cables as illustrated in Figure 4.
Figure4:OutputCoverInsertion
ParallelingCable
Output
Cover
6
5. Assemble two lugs on each bus bar, one on each side, using two hexagon bolts, four plain
washers, two helical spring-lock washers and two hexagon nuts as illustrated in Figure 5.
Figure5:Three10VUnitsLugsAssembly
6. Assemble bus bar insulator prior to output cover assembly. The insulator is flexible and could
be opened in its bottom side. Open the insulator and cover the bus bar by sliding it over the
bus bar, from top to bottom, as illustrated in Figure 6. Repeat for the second bus bar.
Figure6:Three10VUnitsBusBarInsulatorAssembly
Forrecommendedlugsrefer
to seriesSafety&
InstallationManual.
Notsupplied.
HexagonNut,M10,StainlessSteel
HelicalSpring
‐
Lock
Washer,M10,StainlessSteel
PlainWasher,M10,StainlessSteel
M10x25HexagonBolt,StainlessSteel
Tighteningtorque:220‐265Lbf‐inch(24.9‐29.9Nm)
BusBarInsulator
7
7. Fix output cover to the power supplies using six SEMS screws as illustrated in Figure 7.
Figure7:Three10VUnitsOutputCoverAssembly
M3x8SEMSScrew,NickelPlated
Tighteningtorque:4.7
‐
5.7Lbf
‐
inch(0.53
‐
0.64Nm)
8
1.4.2
G/P-3U-20-40V - Assembly Instructions for three 20V-40V units in Parallel
1.4.2.1
Components List
Image Component Quantity
10‐32x5/16PanHeadScrew,StainlessSteel 12
HelicalSpring‐LockWasher,No.10,StainlessSteel 12
PlainWasher,No.10,StainlessSteel 12
ConnectionPlate3U 2
OutputShort 2
M3x4CFlatHeadScrew,NickelPlated 8
ParallelingCable 2
OutputCover 1
9
Image Component Quantity
BusBarInsulator 2
Protection
Insulator
1
M3x8SEMSScrew,NickelPlated 8
10
1.4.2.2
Installation Steps
1. Attach connection plates, one on each side of the power supplies, using 12 pan head screws,
12 helical spring-lock washers and 12 plain washers as illustrated in Figure 8.
Figure8:Three20V‐40VUnitsConnectionPlates3UAssembly
2. Attach output short plates, one on each triple of terminals, using eight flat head screws as
illustrated in Figure 9.
Figure9:Three20V‐40VUnitsOutputShortPlatesAssembly
ConnectionPlate
3U
PlainWasher,No.10,StainlessSteel
HelicalSpring‐LockWasher,No.10,StainlessSteel
10‐32x5/16PanHeadScrew,StainlessSteel
Tighteningtorque:25.4‐31.7Lbf‐inch(2.87‐3.58Nm).
M3x4CFlatHeadScrew,NickelPlated
Tighteningtorque:4.7‐5.7Lbf‐inch(0.53‐0.64Nm)
OutputShort
Otros manuales para Genesys Series
11
Este manual sirve para los siguientes modelos
4
Otros manuales de Fuente de alimentación de TDK-Lambda
TDK-Lambda
TDK-Lambda ELV60 Series Manual de usuario
TDK-Lambda
TDK-Lambda HFE2500-S1U Manual de usuario
TDK-Lambda
TDK-Lambda CUT75 Manual de usuario
TDK-Lambda
TDK-Lambda NVM175 Manual de usuario
TDK-Lambda
TDK-Lambda GENESYS GH1.5kW in 1U Half-Rack 0-600V /... Manual de usuario
TDK-Lambda
TDK-Lambda DPP480-XX-3 Manual del propietario
TDK-Lambda
TDK-Lambda Genesys GEN8-300 Manual de usuario
TDK-Lambda
TDK-Lambda HWS300 Series Manual de usuario
TDK-Lambda
TDK-Lambda Z10-20 Manual de usuario
TDK-Lambda
TDK-Lambda HWS 1000/ME Series Manual de usuario
TDK-Lambda
TDK-Lambda SWS-L Series Manual de usuario
TDK-Lambda
TDK-Lambda CUS200LD Manual de usuario
TDK-Lambda
TDK-Lambda HWS 1500 Series Manual de usuario
TDK-Lambda
TDK-Lambda CUT35 Series Manual de usuario
TDK-Lambda
TDK-Lambda CUS150M1 Series Manual de usuario
TDK-Lambda
TDK-Lambda CUS60M Manual de usuario
TDK-Lambda
TDK-Lambda Z+ series Manual de usuario
TDK-Lambda
TDK-Lambda PHV Series Guía del usuario
TDK-Lambda
TDK-Lambda EZA2500W Series Guía de instalación
TDK-Lambda
TDK-Lambda GXE600 Series Manual de uso y cuidado
