1643043B (401509) 2020-SEPT-2421643043B (401509) 2020-SEPT-243
DATE PURCHASED __________________________________________________________________
HOIST SERIAL NUMBER ____________________________________________________________
CYLINDER SERIAL NUMBER ______________________________________________________
DEALER __________________________________________________________________
ADDRESS __________________________________________________________________
PHONE __________________________________________________________________
FOREWORD
The Stingray twin cylinder underbody hoist is designed for use on single and tandem axle trucks with 12 to
28 foot bodies. The Stingray line provides hoists ranging from Model 1900 in NTEA class F to the Model
7700 in NTEA class L.
This manual contains the information needed for the proper installation and operation of these hoists.
These instructions are for standard installations using a self contained reservoir/valve unit. Study this
manual carefully before attempting to install or operate this product. Other hydraulic packages will come
with supplemental instruction sheets when needed. With the proper installation, use and regular mainte-
nance, Crysteel’s Stingray hoist will give many years of trouble free service.
When ordering parts, be sure to give serial number of hoist, pump, and cylinder. The serial number of the
pump is found on the plate on the pump. The serial number of the cylinder is stamped on the barrel of the
cylinder near the base. For future reference, copy these numbers NOW in the space provided above. Order
parts by number and description as given in the parts listing in this manual.
1. Engage PTO from cab and adjust engine speed to fast idle.
OPERATIONANDUSE
SOMEDO’SANDDON’TSFORSAFEANDLONGSERVICE
1. Usetheproperhydraulicuid.KEEPITCLEAN.Remembertochangeitregularly.
2. ALWAYS operate the hoist from inside the cab of the truck.
3. If the hydraulic hose connections are correct, the hoist should raise when the hoist control
lever is pulled back, hold when the lever is in the center detent, and lower when the lever
is pushed forward.
4. To raise the hoist, pull the control lever back. To hold the body in a raised position, place
the control lever in its center detent position. To lower the hoist, push the control lever
forward.
5. ALWAYS return the hoist control lever to its center detent position after each use.
6. Whenthehoistcylinderreachestheendofthestroke,oilwillowthroughtheautomatic
bypass valve built into the piston inside the cylinder and return to the reservoir.
7. It is advisable to run the PTO to “power down” or lower the hoist because this will act as
an hydraulic lock to hold the hoist in the lowered position. It is not necessary to do this,
however,becausethereservoirhassucientcapacitywhetherornotthehoistispowered
down.Youwillbenetfromtheadvantagesofthedoubleactinghoistonlyifyoupower
down.
8. To make use of the hydraulic lock feature, place the hoist control lever in the center hold
position after the hoist is powered down. This places the pressure on the valve, where it
belongs, not on the pump.
9. DO NOT LEAVE THE PTO IN GEAR WHILE TRANSPORTING. THIS CAN CAUSE
SEVERE DAMAGE TO THE PTO OR HYDRAULIC PUMP.
10.Thehydraulicsystemshouldbedrained,ushedandrelledwithproperhydraulicuid
atregularintervals.CAUTION:NEVERusehydraulicBRAKEFLUIDinthehydraulic
system.
11.Afteraddingorreplacingthehydraulicuid,cyclethehoistseveraltimestoremoveair
from the cylinders and hydraulic hoses.
2. Lubricateallgreasettingsevery100cyclesoreverytwomonths.Infrequentorinsu-
cient lubrication will cause hoist failure and possibly injury or death.
3. ALWAYS carefully block up the body, using the body prop, before working under it.
4. Do not “race” the engine when unloading.
5. Do not load the hoist beyond its capacity.
6. DO NOT tamper with the hydraulic relief valve. This will void the warranty. It can cause
severe damage to the hoist and cylinder.
7. Never leave the PTO in gear while transporting. It could ruin the hydraulic pump, the PTO
or the transmission.
8. Checkallboltsandttingsregularly.Keepthemtight.Seetableonpage5fortorqueval-
ues.
9. Alwaysoperatehoistonarmandlevelsurface.
10. Always make sure area around truck is clear and safe for hoist operation and dumping.
