Tatung VS-10S Manual de usuario

- 1 -

VS-10S

SERVICE MANUAL

- 2 -

CONTENTS

1 SPECIFICATION

2 OPERATING INSTRUCTIONS

3 IMPORTANT SAFEGUARDS

4 ADJUSTMENT PROCEDURE

5 BLOCK DIAGRAM

6 SERVICE NOTES

7 CIRCUIT DIAGRAM

8 LAYOUT DIAGRAM

9 EXPLODED DRAWING

10 PARTS LIST

- 3 -

1 SPECIFICATION

10” Mono Chrome Monitor

CRT SIZE : 10” (9V)

DOT PITCH : 0.26

DEFLECTION ANGLE : 90º

SCAN FREQ. : HOR. 31.5KHz, 35KHz, 38 KHz

VER.50~90Hz

RESOLUTION : 640 x 480, 800 x 600, 1024 x 768

BANDWIDTH : 26 MHz, 35 MHz, 45MHz

VIDEO SIGNAL : VIDEO ANALOG 0.7V/75Ω

SYNC INPUT TYPE : H - SYNC, V - SYNC TTL

INPUT CONNECTOR : 15 PIN D SHELL

USER CONTROL : BRI, CON, POWER SW, V - SIZE,

H - SIZE, V – CENTER

INPUT VOLTAGE : AC 100 ~ 240V, 50 ~ 60 Hz (AUTO)

POWER CONSUMPTION : 68W MAX.

DIMENSION : 257W x 270H x 300D mm

NET WEIGHT : 6.8 Kg

SAFETY : UL, CUL, DHHS, TÜV – GS

EMI : FCC – B, CE

- 4 -

2 OPERATING INSTRUCTIONS

2-1 POWER SWITCH

Turn on the power switch on your PC system. Then turn on the power of

the monitor by pressing the switch on the front of the unit.

2-2 POWER INDICATOR

A green indicator LED indicated the power is on. An orange indicator LED

indicates the power is in power saving mode.

2-3 BRIGHTNESS ADJUSTMENT

Adjust the control to get the desired level of brightness. Rotate clockwise

for brighter on the background.

2-4 CONTRAST ADJUSTMENT

Adjust the control to get the desired level of contrast. Rotate clockwise to

get more contrast.

2-5 HORIZONTAL-SIZE ADJUSTMENT

Adjust the control to get adequate horizontal size. Rotate clockwise to get a

fuller display size.

2-6 VERTICAL-SIZE ADJUSTMENT

Adjust the control to get adequate vertical size. Rotate clockwise to get a

larger display size.

2-7 VERTICAL-CENTER ADJUSTMENT

Adjust the control to get adequate vertical position. Rotate clockwise to

move the screen up.

2-8 HORIZONTAL-PHASE ADJUSTMENT

Adjust the control to get adequate horizontal position. Rotate clockwise to

reposition to the right.

- 5 -

3 IMPORTANT SAFEGUARDS

For your own safety, read all of these instructions and save them for later

reference.

3-1 POWER PLUG

This display monitor is equipped with a 3-wire grounding type power plug.

The third pin provides a safety ground for the display frame and will fit

only into the power outlet of compatible configuration.

Contact your technician to replace the obsolete outlet. Do not defeat the

safety purpose of the grounding plug.

3-2 POWER INPUT

This display should be operated only from the types of power source

indicated on the label. If there is any question about the type of power

supplied to the outlet, consult your technician or dealer.

3-3 VENTILATION

Openings on the cabinet back and bottom are provided for ventilation. To

insure reliable operation and to protect the display from overheating, these

openings must not be blocked or covered. Do not place the display near or

over a radiator or heating vent. If this unit is installed within another

enclosure be sure that adequate ventilation has been provided.

Never push objects of any kind through the cabinet openings. They may

touch dangerous voltage points or cause short circuits that could result in

fire or electrical shock.

3-4 ATTACHMENTS

Signal sources must be of approved types, properly grounded, if safety

standards are to be maintained ask the service technician to perform routine

safety tests to determine that all equipment is in safe operating condition.

Overloaded or poorly grounded AC power systems can cause severe

difference in ground potential between the display and the signal source.

Particularly on long video lines where the display and the source are

plugged into different AC power circuits. Besides causing signal

instability, ground potential may be great enough to present a shock hazard.

Ground potential test should be a part of the routine safety check carried out

by the service technician.

- 6 -

3-5 CLEANING

Unplug the power cord from the outlet before cleaning the display. Use

only a damp cloth and mild detergent. Do not use strong liquid cleaner or

aerosol sprays. Do not attempt to clean the interior of the unit: this action

must be performed by the service technician as required during normal

maintenance.

3-6 SERVICE

Removal of the back by an unauthorised person may expose the user to

dangerous voltage or other hazards.

Refer all servicing to qualified service personnel. Unplug the display from

the power outlet and notify the service technician should any of the

following occur

(a) If liquid has been spilt into the display

(b) If the display has been exposed to rain or water

(d) If fuses continue to blow

(e) If the power cord is damaged or frayed

(f) If a distinct change from normal operation is apparent.

- 7 -

4 ADJUSTMENT PROCEDURE

This alignment procedure is for adjusting/testing picture performance, in

order to obtain the optimum result, the following adjustment sequence must

be followed step by step:

4-1 Check B+ voltage:

a. Test pattern: 640 x 480 cross-hatch.

b. Set up external brightness and contrast VR to central position.

c. Adjusted VR501 have 95Vdc ± 0.5Vdc use digital multimeter

positive leader test J9 positive point, negative leader to ground.

4-2 Vertical linearity adjustment:

a. Test pattern: 640 x 480 cross-hatch.

b. Set up external brightness and contrast VR to central position.

c. Adjust VR302 to make equal distance between top-center and

bottom-center.

4-3 Horizontal-hold adjustment:

a. Test pattern: 640 x 480 cross-hatch.

b. Set up external brightness and contrast VR to central position.

c. Turn off horizontal-sync (pin to ground)

d. Adjust VR602 to make pattern upright.

4-4 Pin-cushion adjustment:

a. Test pattern: 640 x 480 cross-hatch.

b. Set up external brightness and contrast VR to central position.

c. Adjust VR304 make picture to top and bottom ≤2mm, left and right

≤2mm.

4-5 Brightness adjustment:

a. Test pattern: 640 x 480 full-white.

b. Set up external brightness and contrast VR to maximum.

c. Test R251, then adjust VR701 to –20Vdc ± 0.1Vdc.

4-6 X-ray protection adjustment:

a. Test pattern: 640 x 480 cross-hatch.

b. Test TP2, then adjust VR603 to 5.2 Vdc ± 0.1Vdc.

- 8 -

4-7 White balance adjustment:

a. Test pattern: 640 x 480 “2” balance.

b. Set up external brightness and contrast VR to maximum.

c. Adjust VR240, VR243, VR241 have R.G.B. cathode to 55Vdc.

d. Turn external brightness VR to minimum.

e. Set VR209 to central position.

f. Adjust VR245, VR244, VR248 have R.G.B cathode to 30V p-p.

4-8 White balance adjustment:

a. Test pattern: 640 x 480 full-white.

b. Set up external brightness to center.

c. Turn external contrast VR to 2FL.

d. Adjust VR240, VR243, VR241 to X = 281 ± 15 mm,

Y = 298 ± 15 mm.

e. Turn external contrast to maximum.

f. Adjust VR245, VR244, VR248 to X = 281 ± 15 mm,

Y = 298 ± 15 mm.

4-9 Raster brightness adjustment:

a. disconnect video signal.

b. External brightness to maximum.

c. Adjust FBT screen VR to 0.5 ~ 1.5 FL.

4-10 Full-white adjustment:

a. test pattern: 640 x 480 full-white.

b. Set up external brightness VR to center, external contrast VR to

maximum.

c. Adjust VR212 have luminance equal to 25 ~ 45 FL.

4-11 Purity check:

a. test pattern: 640 x 480 full-white

b. set up external brightness and contrast VR to maximum position.

c. Change to Red/Green/Blue colour for every check if purity is good.

4-12 Misconvergence check:

a. test pattern: 640 x 480 cross-hatch

b. use klein optica convergence gauge change to R/B, R/G, B/G colour

for every check misconvergence.

c. center area (d = 0.15 mm), A zone, B zone (0.4mm).

- 9 -

- 10 -

Tabla de contenidos

Otros manuales de Monitor de Tatung

Tatung

Tatung TME24 Manual de usuario

Tatung

Tatung TCM-0902 Manual de usuario

Tatung

Tatung none Manual de usuario

Tatung

Tatung TLM-1903 Manual de usuario

Tatung

Tatung TME50 Manual de usuario

Tatung

Tatung TME19WE Manual de usuario

Tatung

Tatung 7005L Manual de usuario

Tatung

Tatung DS42-AV Manual de usuario

Tatung

Tatung Vibrant L2ES-TP6720 Manual de usuario

Tatung

Tatung TCM-2102s Manual de usuario

Tatung

Tatung 5005L13 Manual de usuario

Tatung

Tatung TM32 Manual de usuario

Tatung

Tatung VM9K9DA Manual de usuario

Tatung

Tatung TME 17 Manual de usuario

Tatung

Tatung F Series Manual de usuario

Tatung

Tatung TME32A Manual de usuario

Tatung

Tatung Vibrant VM78F Manual de usuario

Tatung

Tatung Vibrant VM77S Manual de usuario

Tatung

Tatung VM7K9 Manual de usuario

Tatung

Tatung VM9AF Manual de usuario

Tatung

Tatung TME32 Manual de usuario

Tatung

Tatung VM-14AF Manual de usuario

Tatung

Tatung Triview T5DVI Manual de usuario

Tatung

Tatung VM9K9DA P990S Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación