taskit Portux920T EU Manual de usuario
Quick Start Guide taskit GmbH
Quick Start Guide
for
Portux920T EU / SW
Portux Mini-PC
Portux Panel-PC
Panel-Card
MoLUX
Sta p
Page 1 of 15 Version 1.14
Quick Start Guide taskit GmbH
taskit G bH
Seelenbinderstr. 33
D-12555 Berlin
Ger any
Tel. +49 (30) 611295-0
Fax +49 (30) 611295-10
http://www.taskit.de
© taskit GmbH, Berlin
All rights reser ed. This document and the products referred to herein are copyrighted works
of taskit GmbH. Information in this document is subject to change without notice. No part of this
document may be reproduced or transmitted in any form, without the express written permission of
taskit GmbH. If howe er, your only means of access is electronic, permission to print one copy is
hereby granted. Neither taskit GmbH nor taskit´s distributors assume any liability arising from the
use of this manual/guide or any product described herein.
Page 2 of 15 Version 1.14
Quick Start Guide taskit GmbH
Table of contents
1.Introduction...................................................................................4
2.Package contents.........................................................................5
2.1.Portux920T EU......................................................................................5
2.2.Portux920T SW.....................................................................................5
2.3.Portux Mini-PC......................................................................................5
2.4.Portux Panel-PC...................................................................................6
2.5.Panel-Card.............................................................................................6
2.6.MoLUX...................................................................................................7
2.7.Sta p....................................................................................................7
3.Setting up the Hardware..............................................................9
3.1.Portux920T EU......................................................................................9
3.2.Portux Mini-PC......................................................................................9
3.3.Portux Panel-PC without alu iniu -case.........................................9
3.4.Portux Panel-PC with alu iniu -case.............................................10
3.5.Panel-Card...........................................................................................10
4.Creating a ter inal connection to a PC...................................11
4.1.Ter inal access under Linux............................................................11
4.2.Ter inal access under Windows......................................................12
5.The boot process / login............................................................13
6.Copying files or applications....................................................14
6.1.Sharing a directory.............................................................................14
6.2.Setting up the ethernet connection..................................................14
6.3.Mounting the directory.......................................................................15
6.4.Copying a file......................................................................................15
6.5.Starting an application.......................................................................15
Page 3 of 15 Version 1.14
Quick Start Guide taskit GmbH
1. Introduction
Your product is delivered with an customized Linux and the bootloader U-Boot. To start running
you have to read the Quic StartGuide.
If you want to configure the Linux ernel, install permanent drivers or software or modify the
bootloader you have to wor the LinuxGuide over.
Maybe you want to develop additional hardware components and drivers then you will need the
informations and specifications from the TechnicalReference and the Atmel® Manual.
Page 4 of 15 Version 1.14
Quick Start Guide taskit GmbH
2. Package contents
2.1. Portux920T EU
Standard
If you have ordered the Portux920T EU, following parts are delivered:
●Portux920T EU
Starterkit
If you have ordered the Portux920T EU starter it, following parts are delivered:
●Portux920T EU
●PXB-USB
●Firmware CD (Documentation, Linux, U-Boot and GNU-Tools)
●Ethernet cable (patch and crossover)
●Null modem cable
●Power pac
●DBGU adapter
Also available
For the Portux920T EU following parts can be ordered seperatelly:
●PXB-Modem ISDN or Analog
2.2. Portux920T SW
Standard
If you have ordered the Portux920T SW, following parts are delivered:
●Portux920T SW
2.3. Portux Mini-PC
Standard
If you have ordered the Portux Mini-PC, following parts are delivered:
●Robust aluminium housing including:
○Portux920T EU
Page 5 of 15 Version 1.14
Quick Start Guide taskit GmbH
○PXB-USB
Starterkit
If you have ordered the Portux Mini-PC starter it, following parts are delivered:
●Robust aluminium housing including:
○Portux920T EU
○PXB-USB
●Firmware CD (Documentation, Linux, U-Boot and GNU-Tools)
●Ethernet cable (patch and crossover)
●Null modem cable
●Power pac
●DBGU adapter
2.4. Portux Panel-PC
If you have ordered the Portux Panel-PC with aluminium case the front panel with Display, matrix
eyboard and an optional touch panel is already installed in the aluminium case. Furthermore a
power jac and a power button are installed on the top.
If you have ordered the Portux Panel-PC without aluminium case the Portux Panel-PC board and
the front panel with Display and matrix eyboard and an optional touch panel comes to you as
separate parts. Furthermore a power connecting cable is provided.
Irrespective of what product you ordered following parts are delivered:
●Firmware CD (Documentation, Linux, U-Boot and GNU-Tools)
●Ethernet cable (patch and crossover)
●Null modem cable
●Power pac
●DBGU adapter
2.5. Panel-Card
Standard
If you have ordered the Panel-Card, following parts are delivered:
●Panel-Card with TFT-Display
Page 6 of 15 Version 1.14
Quick Start Guide taskit GmbH
Starterkit
If you have ordered the Panel-Card starter it, following parts are delivered:
●Panel-Card with TFT-Display
●Starter it baseboard
●Firmware CD (Documentation, Linux, U-Boot and GNU-Tools)
●Ethernet cable (patch and crossover)
●Null modem cable
●Power pac
●DBGU adapter
2.6. MoLUX
Standard
If you have ordered the MoLUX, following parts are delivered:
●MoLUX housing including:
○Panel-Card with TFT-Display
○Lithium-ion battery pac
●Firmware CD (Documentation, Linux, U-Boot and GNU-Tools)
Also available
For the MoLUX following parts can be ordered seperatelly:
●Doc ing station with power pac and USB cable
2.7. Sta p
Standard
If you have ordered the Stamp, following parts are delivered:
●Stamp
Starterkit
If you have ordered the Stamp starter it, following parts are delivered:
●Stamp
Page 7 of 15 Version 1.14
Quick Start Guide taskit GmbH
●Stampadaptor (for starter it baseboard)
●Starter it baseboard
●Firmware CD (Documentation, Linux, U-Boot and GNU-Tools)
●Ethernet cable (patch and crossover)
●Null modem cable
●Power pac
●DBGU adapter
Page 8 of 15 Version 1.14
Quick Start Guide taskit GmbH
3. Setting up the Hardware
3.1. Portux920T EU
First connect a 2-wire power connecting cable to X7 (VIN). Pay attention to connect the red wire
with VIN+ and the blac wire with VIN-. For the safe loc ing of the cable the orange interior of the
mini force clamp must be pressed downward and the cable end be completely introduced. Examine
the firm tightness of the cables.
Then connect a null modem cable from you PC to the first serial port (X6, RS232-1). Due to the
fact that the first serial port provides 2 RS232 interfaces, it is required to connect the DBGU atapter
to X6 and then connect the serial cable to the DBGU adapter to access the first serial interface
(debug port).
Before you turn it on for the first time, start a terminal emulation program on the connected
computer as described below (“Creating a terminal connection to a PC”).
3.2. Portux Mini-PC
Connect a null modem cable from you PC to the first serial port (RS232-1) of the Portux Mini-PC.
Due to the fact that the first serial port provides 2 RS232 interfaces, it is required to connect the
DBGU atapter to RS232-1 and then connect the serial cable to the DBGU adapter to access the first
serial interface (debug port).
Next, connect the Portux Mini-PC to the power pac . This concludes the hardware setup. Before
you turn it on for the first time, start a terminal emulation program on the connected computer as
described below (“Creating a terminal connection to a PC”).
3.3. Portux Panel-PC without alu iniu -case
First connect the matrix eyboard with the Portux Panel-PC board via the slot X41 (Keyb). Ensure
to connect the matrix eyboard in that way the the arrow on the jac is connected to the arrow
(Pin1) on the slot of the Portux Panel-PC board.
Then connect the LCD. First connect the two-wire cable to slot X21 (high voltage) then connect the
data cable to the Portux Panel-PC board using the corresponding slot for your LC-Display:
●connect a monochrome LCD to slot X16 (B/W LCD) on the Portux Panel-PC board
●connect a CSTN-display to slot X22 (CSTN) on the Portux Panel-PC board
●connect a TFT display to slot X28 (TFT) on the Portux Panel-PC board
If you have ordered a Portux Panel-PC with touch-screen then connect the jac of the touch-screen
to slot X18 (Touch) on the Portux Panel-PC board (the arrow points to Pin1).
Now connect the 2-wire power connecting cable to X7 (VIN). Pay attention to connect the red wire
with VIN+ and the blac wire with VIN-. For the safe loc ing of the cable the orange interior of the
Page 9 of 15 Version 1.14
Quick Start Guide taskit GmbH
mini force clamp must be pressed downward and the cable end be completely introduced. Examine
the firm tightness of the cables.
Follow the steps described below (“Portux Panel-PC with aluminium-case”) to connect the Portux
Panel-PC to a PC.
3.4. Portux Panel-PC with alu iniu -case
Connect the first serial interface off the Portux Panel-PC (mar ed as RS232-1) using the DBGU
adapter (the DBGU adapter converts the RS232-1 slot from DGBU to standard RS232 pinout) and
the null modem cable to an available serial interface on the computer to which you want to create a
connection.
Next, connect the Portux Panel-PC to the included power pac . This concludes the hardware setup.
Before you turn on the Portux Panel-PC for the first time, start a terminal emulation program on the
connected computer as described below (“Creating a terminal connection to a PC”).
3.5. Panel-Card
Connect a null modem cable from you PC to the first serial port (RS232-1). Due to the fact that the
first serial port provides 2 RS232 interfaces, it is required to connect the DBGU atapter to RS232-1
and then connect the serial cable to the DBGU adapter to access the first serial interface (debug
port).
Next, connect the Panel-Card to the power pac . This concludes the hardware setup. Before you
turn on the Panel-Card for the first time, start a terminal emulation program on the connected
computer as described below (“Creating a terminal connection to a PC”).
Attention: Removing the Panel-Card from the baseboard should be done with care and only when
absolutely essential.
Because if the Panel-Card is cant, the spring contacts will be damaged.
When the spring contacts are damaged, the pins of the baseboard don't have electric contact to the
Panel-Card. In this case the Panel-Card won't be functioning any more.
Page 10 of 15 Version 1.14
Este manual sirve para los siguientes modelos
6
Tabla de contenidos
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
