TANDBERG 420LTO Manual de usuario

Revision 1 – February 2005

Tandberg 420LTO

Half Height LTO2 Tape Drive

Quick Installation Guide

Mechanical Installation

For mechanical mounting specifications, please refer to Figure 1.

Allowed mounting position is either horizontal with the indicator LEDs to the

right, or vertical with the LEDs up.

The drive occupies a half-size 5.25-inch slot with standard holes for mounting

screws on both sides of the drive chassis and at the bottom of the drive.

Figure 1 Mounting specifications

Important!

Mounting screw

requirements

•Only M3 (metric) screws must be used for mounting the drive

•Maximum permitted screw penetration: 3.0 mm

•Minimum required screw penetration: 2.0 mm

•Screw torque, mounting screws: 0.5 Nm

•Screws are supplied with all the Tandberg 420LTO drive

variants

Do not use longer screws or higher screw torque

than specified!

Figure 2 Allowed mounting orientations

SCSI Identification

Make sure that the drive unit has the proper SCSI-ID before it is connected to a

computer system.

Refer to manuals for host computer and application software to obtain the correct

ID. For correct mounting of ID-jumpers at the rear of the drive, please refer to

Figure 3 and Table 1.

External drives have a thumb-wheel switch to set the SCSI-ID (see Figure 6).

Figure 3 Drive connectors

The factory default drive

number setting is SCSI ID = 2.

If the drive has to be set up

with a different unit number,

the straps (on the Service

Connector) have to be

connected according to

Table 1.

Example: SCSI ID = 3

Table 1 Service Connector strap settings

for SCSI ID (Dark = Strap mounted)

Power Connector SCSI Connector

Service Connector

SCSI ID=0

SCSI ID=1

SCSI ID=2

SCSI ID=3

SCSI ID=4

SCSI ID=5

SCSI ID=6

SCSI ID=7

SCSI ID=8

SCSI ID=9

SCSI ID=10

SCSI ID=11

SCSI ID=12

SCSI ID=13

SCSI ID=14

SCSI ID=15

SCSI Cable

Figure 4 SCSI cable

•Internal SCSI-LVD/SE-cable with 5 connectors (Ordering no. 43 32 63)

•Internal, removable SCSI-LVD/SE-terminator (Ordering no. 43 20 53)

•External, removable SCSI-LVD/SE-terminator (Ordering no. 43 20 52)

•External SCSI 68HD/VHDCI 320MBs (Ordering no. 43 32 64)

Termination

The SCSI-bus cable must be terminated in both ends according to SCSI

specifications. If the tape drive is the last device on the bus, the bus must be

terminated within 10 cm of the tape drive connection.

Tandberg 420LTO has a combined SCSI-LVD/SE interface embedded. The PC-98

Specification specifies that the termination of the SCSI-bus system is a part of the

SCSI-cable and not a part of the SCSI-device.

As a result, termination cannot be turned on or off directly on the tape drive itself.

For internal devices, a SCSI-cable with an integrated terminator or a separate

terminator applied to the end connector of the cable, 10 cm from the last device,

must be used.

External devices must be terminated with an external terminator on the last device

on the SCSI-bus.

Software Installation

For Software Application support and software drivers, please see

www.tandberg.com/ > SUPPORT > LTO Support and www.tandberg.com/ >

SUPPORT > Software Compatibility

For installation of Backup Application software, refer to the software vendor’s

software application user guide supplied with the software or on the software

vendor’s web.

Host Last SCSI Device

Internal Terminator Connector

SCSI

bus

10 cm

Front LED Indicators

Figure 5 Light Emitting Diodes (LED)

Drive State READY LED

(Green left) ACTIVITY LED

(Green) CLEAN LED

(Amber) FAULT LED

(Amber right)

LED-test.

The LEDs are turned ON one-by-one.

Power-On Self-Test starts in parallel

with the LED-test .

ON ON ON ON

Cartridge not loaded. OFF OFF ON / OFF OFF

Cartridge loaded, no activity ON OFF ON / OFF OFF

Cartridge loaded, activity ON Flashing ON / OFF OFF

Cleaning OFF Flashing ON OFF

Cartridge loading or unloading OFF Flashing ON / OFF OFF

Unrecoverable drive failure ON / OFF OFF ON / OFF Flashing

Over temperature OFF OFF ON / OFF ON

Media Error (wrong, write protected or

harmed media) OFF Flashing ON / OFF Flashing

Table 2 Front LED behavior during normal operation

For a complete description of LED behavior see Tandberg 420LTO Reference

Manual.

Media and Capacities

Drive Model Media Name Tape Length Capacity

(Native)

Tandberg

420LTO LTO Ultrium Generation 2 (Native format)

LTO Ultrium Generation 1 (Read/Write compatible) 609 m

609 m 200 GByte

100 GByte

Table 3 Media alternatives

External Tabletop Enclosure

Figure 6 External tabletop enclosure, rear side

Power Requirements

Tandberg 420LTO in external tabletop enclosure:

AC Input: 100 VAC / 0.6 A or 240 VAC / 0.3 A, 50-60 Hz

Tandberg 420LTO as standalone:

DC Input (typical operation): 5 VDC / 2.1 A, 12 VDC / 0.6 A

Heat Dissipation

Tandberg 420LTO as standalone:

Operating: 18 W

Sleep mode with cartridge inserted: 9 W

Cooling Fan SCSI_ID Switch

SCSI Interface ConnectorsPower Connector

ON/OFF Switch

Total customer satisfaction is of the utmost importance

to Tandberg Data.

We guarantee that this product left our premises defect free.

If you are not satisfied with the quality of this product,

please contact your distributor or the nearest

Tandberg Data office to have the problem solved!

For more documentation and information, please see our website

www.tandberg.com.

Tandberg Data

International headquarters

Tandberg Data ASA, Kjelsåsveien 161, Oslo, P.O. Box 134 Kjelsås, N-0411 Oslo, Norway.

Tel: +47 22 18 90 90. Fax: +47 22 18 95 50.

www.tandberg.com

Worldwide subsidiaries

Inostor Inc., 13000 Gregg Street, Poway, CA 92064, U.S.A.

Tel: +1 858 726 0277. Fax: +1 858 726 0278.

Tandberg Data GmbH, Feldstrasse 81, D-44141 Dortmund, Germany.

Tel: +49 231 5436 0. Fax: +49 231 5436 111.

Tandberg Data S.A.S., 16/18 Ave. Morane-Saulnier, F-78941 Vélizy Cedex, France.

Tel: +33 1 39 26 01 01/00800-82632374.

Fax: +33 1 34 65 02 89 (for technical support: 00800-07867243).

Tandberg Data (Asia) Pte. Ltd, 20 Bendemeer Road, #04-05 Cyberhub, Singapore 339914,

Tel: +65 6396 0786. Fax: +65 6396 0787.

Tandberg Data (Japan) Inc., Eitaibashi Eco-Piazza Bldg. 8th floor 29-13, Shinkawa 1-chome,

Chuo-ku Tokyo 104-033, Japan

Tel: +81 3 5566 2871. Fax: +81 3 5566 2875.

Tandberg Data (UK) Ltd., Registered Office, High Street Redbourne, Herts AL3 7LW, UK

Tel: 00800-82632374. Fax: 00800-07867243.

Specifications subject to change without notice. All trademarks are the property of their respective owners.

Part No. 433261-01. February 2005.

Tabla de contenidos

Otros manuales de Almacenamiento de TANDBERG

TANDBERG

TANDBERG VXA TAPE DRIVE Manual de usuario

TANDBERG

TANDBERG SDLT600 Hoja de información del producto

TANDBERG

TANDBERG LTO3 Manual de usuario

TANDBERG

TANDBERG 220-420LTO Manual de usuario

TANDBERG

TANDBERG STORAGELIBRARY Manual de usuario

TANDBERG

TANDBERG LTO HH Manual de usuario

TANDBERG

TANDBERG SLR7 Manual de usuario

TANDBERG

TANDBERG 840LTO Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario