Tally T9114 Guía de instalación
Seite -1-
-PostScriptModule
-Barcode Module
-Memory Module
T9114 / T9216
T9120 / T9220
Installation,
Barcode Programming
Seite -2-
PRECAUTIONS
Disconnect The Power Cord
Never remove the printer control board while the printer is plugged in. To avoid the
possibility of electrical shock, always disconnect the power cord when installing or
removing ANY internal or external printer option.
Discharge Static Electricity
The control board and internal printer options (SIMM, Network interface) are sensitive to
static electricity. Before installing or removing an internal option, discharge static electricity
from your body by touching something metal, such as the metal back plate on any device
plugged into a grounded power source.
If you walk round before finishing the installation, discharge any static electricity again.
Copyrights
This manual is provided for information purposes only. All information included herein is
subject to change without notice. Tally is not responsible for any damages, direct or
indirect, arising from or related to use of this manual.
© 2002 Tally Computerdrucker GmbH. All rights reserved.
© 2003 Tally Computerdrucker GmbH. All rights reserved.
-T9114, T9120, T9216, T9412, T9220 and Tally logo are trademarks of
TallyComputerdruckerGmbH
-Centronics is a trademark of Centronics Data Computer Corporation.
-PCL and PCL6 are trademarks of Hewlett-Packard Company.
-IBM and IBM PC are trademarks of International Business Machines Corporation.
-TrueType, Laser Writer and Macintosh are trademarks of Apple Computer Inc.
-Microsoft, Windows, Windows 9x, Windows Me, Windows 2000, Windows NT, Windows
XP and MS-DOS are registered trademarks of Microsoft Corporation.
-PostScript 3 is a trademark of Adobe Systems Inc.
-All other brand or product names are trademarks of their respective companies or
organizations.
Seite -3-
Table of Contents
InstallingtheBarcodemodule 4
InstallingonT9412,T9114,T9216 4
InstallingonT9120 6
InstallingonT9220 10
UsingthemoduleoptionswithinMicrosoftWord 12
SAP Support 13
OCR-B 13
How Barcode module works 14
How to use Barcode module 16
Parameter description 17
Tparameter Esc(s#T (Bar Code System) 17
Pparameter Esc(s#P (Human readable text) 18
Hparameter Esc(s#H(HRTFont) 18
Vparameter Esc(s#H(VerticalSIze) 19
Bparameter Esc(s#1,#2[,#3,#]4B (Black Bars widths) 19
Sparameter Esc(s#1,#2[,#3,#]4B (White Bars widths) 19
PrintExtendedCharactersandleadingspaces 20
Code 128 Control Codes 20
PCL Escape Sequences Examples 21
Default parameters 22
Bar Code Formats Characteristics: Size 23
„Barcode & More“ Fonts 24
Trouble shooting 27
Barcode Testpage sample 29
Trademarks 31
Seite -4-
Additional memory, Barcode and the PostScript option are provided on SIMMs.
Notes: Since PostScript setting requires 12 MB of printer memory and the T9114 / T9412 comes with 4 MB
standard, installation of the PS SIMM requires installation of a 8 MB SIMM memory as well.
1Turn the power off and unplug all cables from the printer
2Remove the two screws on the rear of the printer,
then remove the control board cover.
3Locate the Barcode/PostScript SIMM slot (lower slot on
the left as shown) and the memory SIMM slot (upper
slot) on the control board. They are not interchangeable.
- To install the Memory SIMM, continue with Step 4.
- To install the Barcode / PostScript SIMM, go to Step 6.
4Hold the memory SIMM so that the notch Œand the
connection point •are aligned with the slot as shown.
T9412/T9114: Insert the SIMM all the way into the upper
slot labeled DRAM MODULE at a 45 degrees angle
.T9216:Insert the SIMM all the way into the lower slot
labeled DRAM MODULE at a 90 degrees angle.
Next step 6)
T9412 / T9216 / T9114
Memory, PostScript and Barcode Installation.
T9412/T9114
Seite -5-
5Rotate it up until it snaps into place.
6Hold the memory SIMM so that the notch Œand the
connection point •are aligned with the slot as shown.
T9412/T9114: Insert the SIMM all the way into the lower
slot labeled FLASH-ROM MODULE at a 45 degrees
angle.
T9216: Insert the SIMM all the way into the upper
slot labeled FLASH-ROM MODULE at a 90 degrees
angle. Next step 8)
7Rotate it up until it snaps into place.
8Make sure that the SIMMs are secured in place by
the metal clips and pins on both sides of the connectors.
9Reconnect the power cord and turn the printer on.
Note: For PostScript driver installation and usage information on a Macintosh system, refer to Appendix
C, “Using Your Printer with a Macintosh.” For PS printing on a Windows system, refer to Appendix
E, “Using Windows PostScript Driver.” of the printers reference manual.
Seite -6-
1Unplug the printer power cord.
2Disconnect all cables from the back of the printer.Prep
arations
3Remove the printer cover .
aOpen the rear cover.
bRemove the two screws from the back of the printer.
Save the screws.
cGrasp the cover (as illustrated) and pull it firmly
toward the rear of the printer until it stops.
dRemove the cover from the printer.
eRemove the five screws from the metal plate
covering the control board.
fRemove the plate.
Closing The Printer Cover
T9120 Memory, Barcode and PostScript Installation.
Seite -7-
If the printer cover is opened,
you can see the printer control board as below.
ROM SIMM Network Card
Connector Connector
Understanding the Printer Control Board Printer Memory Serial/LocalTalk
Connector Connector
The printer memory option increases the printer´s dynamic random access memory (DRAM). Your printer
was shipped with 16MB of standard printer memory. You can install two printer memory options in your
printer. Printer memory upgrade options available are 4, 8, 16, 32, 64 and 128MB.
Notes: Your machine recognizes only half of 8MB, 32MB and 128MB SIMMs if installed in the slot CN4.
DRAM SIMM Features for Upgrade
- Speed(Access Time): 60nS
- Refresh Time: 1K(1024 cycles/16 ms) / 2K(2048 cycles/32 ms)
- The Method of refresh is CAS-befor-RAS refresh
- Mode: EDO Type
- Single +5V +/-10% power supply
- The SDRAM does not support
Notes: The printer memory option is easily damaged by static electricity. Touch something metal before
you touch the memory option.
Memory
Connector
CN 3
CN 4
CN 5Printer Memory
CN 4: This slot recognizes only half of 8MB, 32MB
and 128MB SIMMs if they are installed.
Seite -8-
4Unpack the SIMM module.
Notes: Avoid touching the connection points along
the edge.
Save the packaging.6
5Hold the SIMM module with the connection points
pointing toward the connector and position the notch
as shown. Insert the memory option all the way into
the connector at a 30Oangle, and rotate it left until
it snaps into place.
6
6Make sure both metal clips on the connector are
fastened, and the two pins on each of the connectors
are pushed through the holes on the SIMM module.
7Close the metal plate and tighten all the screws.
8Set the bottom of the cover onto the printer. Make
sure the bottom tabs on the cover fit into the
corresponding slots in the printer. Rotate the cover
up towards the printer. Slide the cover toward the
front of the printer until it clicks into place.
PostScript module
Memory module
Seite -9-
9Gently tighten all the screws
10 Reconnect any interface cables and the power cord.
11 Memory module:
Set the printer memory item on the printer tab of
the properties dialogue box to the value of the added
printer memory.
Barcode / PostScript module:
Install the PostScript driver from the printers CD
to use the PostScript emulation.
Removing a SIMM module
1Push the metal clips at each end of the connector
away from memory option.
2Rotate the memory option right to a 30Oangle and
gently pull it out of the connector as shown.
3Place the printer memory option in its original
packaging.
Notes: Store the SIMM module in the original packaging
due to a damage by static electricity
Seite -10-
T9220
Memory, PostScript (PS) and Barcode Installation.
Additional memory, Barcode and the PS option are provided on DIMMs.
1Turn the power off and unplug all cables from the printer
2Remove the two screws on the rear of the printer,
then remove the control board cover.
3Locate the Barcode/PS DIMM slot (upper slot)
and the memory SIMM slot (lower slot) on the control board.
They are not interchangeable.
- To install theMemory DIMM, continue with Step 5.
- To install the Barcode / PS DIMM, go to Step 4.
Otros manuales para T9114
1
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Impresora de Tally
Tally
Tally Tally Colour Laser T8006e Manual de usuario
Tally
Tally T6218 Guía de configuración
Tally
Tally T2140 Manual de usuario
Tally
Tally XPRESS T9412i Manual de usuario
Tally
Tally T 2045 Manual de usuario
Tally
Tally T2040 Manual de usuario
Tally
Tally T6215 Manual de usuario
Tally
Tally Dascom 1125 Manual de usuario
Tally
Tally T2150 SprintPro Manual de usuario
Tally
Tally T2030/24 Manual de usuario
Tally
Tally T2030/24 Manual de usuario
Tally
Tally T2240 Manual de usuario
Tally
Tally T6215 Manual de usuario
Tally
Tally T2265 SprintPro Manual de usuario
Tally
Tally T9312 Manual de usuario
Tally
Tally T 2060 Manual de usuario
Tally
Tally T2033S Manual de usuario
Tally
Tally T2150 Manual de usuario
Tally
Tally T8106 Manual de usuario
Tally
Tally T2240/24 Manual de usuario
