Talkaphone VOIP-500 Series Guía de configuración rápida
VOIP-500Series Phone/WEBS Paging Modules
Rave Mobile Safety Integration Guide
Page 1of 4Rev. 11/29/12
Copyright 2012 Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714 • Phone 773.539.1100 • [email protected] • www.talkaphone.com.
All prices and specifications are subject to change without notice. Talk-A-Phone, Scream Alert, WEBS and WEBS Contact are registered trademarks of Talk-A-Phone Co. All rights reserved.
I. Introduction
This guide provides general instructions for integration of the VOIP-500 Series Phone/WEBS Paging Modules
with a Rave Mobile Safety account. Please read this instruction set completely before making any changes to
the system. For detailed VOIP-500 Series Phone setup instructions, please consult the VOIP-500 Series
Phone Manual.
II. Prerequisites
VOIP-500 Series Phone/WEBS Paging Modules registered to receive direct inward dialing (DID)
service calls and DTMF through a SIP proxy or registrar
SIP proxy/registrar setup with direct inward dialing (DID) service
Rave Mobile Safety account
Network access to the Rave Mobile Safety account and VOIP-500 Series Phone/WEBS Paging
Module
III. Talk-A-Phone VOIP-500 Series Phone/Paging Modules Configuration
1. In the VOIP-500 main menu, select VOIP > Paging Settings.
2. Enter the following fields on the Paging Settings page. Then click Apply.
Select Paging Output:
Choose Speaker if a standalone VOIP-500 or WEBS-PA-1
Choose Line Level Output if a WEBS-CM-2, WEBS-PA-2IP, or connected to a WEBS Tower
Add gain to incoming page before sending to specified output:
Output Gain: Range from 1-20, default setting is 20.
Automatically activate paging for inbound Phone calls:
Select No, as we need to use DTMF tones to be able to select specific devices.
Key code to activate paging during an inbound call is:
Select this check box and enter desired code.
Key code to deactivate paging during an inbound call is:
Select this check box if needed and enter desired code.
VOIP-500Series Phone/WEBS Paging Modules
Rave Mobile Safety Integration Guide
Page 2of 4Rev. 11/29/12
Copyright 2012 Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714 • Phone 773.539.1100 • [email protected] • www.talkaphone.com.
All prices and specifications are subject to change without notice. Talk-A-Phone, Scream Alert, WEBS and WEBS Contact are registered trademarks of Talk-A-Phone Co. All rights reserved.
3. If Line Level Output was selected in Step 2, then the VOIP-500 may need to be configured to activate
an amplifier via an Auxiliary Output. From the VOIP-500 Main Menu select Devices > Auxiliary
Outputs.
4. From the dropdown menu at the top of the page, select the Auxiliary Output that is being used to
activate the amplifier.
5. Under Activate Auxiliary Output upon events,scroll down to Remote Side Key Codes. Check the
box and then enter the key code to activate the amplifier. This can be the same as the code used in
Step 2.
VOIP-500Series Phone/WEBS Paging Modules
Rave Mobile Safety Integration Guide
Page 3of 4Rev. 11/29/12
Copyright 2012 Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714 • Phone 773.539.1100 • [email protected] • www.talkaphone.com.
All prices and specifications are subject to change without notice. Talk-A-Phone, Scream Alert, WEBS and WEBS Contact are registered trademarks of Talk-A-Phone Co. All rights reserved.
6. Select Authentication from the VOIP-500 Main Menu.
7. Authentication to activate Auxiliary Outputs can be enabled if desired. Complete the following steps and
then click Apply.
DTMF Access Code:
Guard Access Code always begins with *4* and then the code desired followed by a *.
Aux. Output Activation/Deactivation: If authentication is desired check this box.
VOIP-500Series Phone/WEBS Paging Modules
Rave Mobile Safety Integration Guide
Page 4of 4Rev. 11/29/12
Copyright 2012 Talk-A-Phone Co. • 7530 North Natchez Avenue • Niles, Illinois 60714 • Phone 773.539.1100 • [email protected] • www.talkaphone.com.
All prices and specifications are subject to change without notice. Talk-A-Phone, Scream Alert, WEBS and WEBS Contact are registered trademarks of Talk-A-Phone Co. All rights reserved.
IV. Rave Mobile Safety Basic Configuration
Basic instructions for integrating a VOIP-500 Series Phone/WEBS Paging Module with Rave Mobile Safety
are included. Advanced setup of Rave Mobile Safety features is outside the scope of this document.
1. Using a web browser, log in to your Rave Mobile Safety account.
2. From the “My Account” screen, click “Add” to add the direct inward dialing (DID) phone number of a
VOIP-500 Series Phone/WEBS Paging Module.In the United States, a DID phone number is
typically comprised of 10-digits (i.e. 3-digit area code + 7-digit phone number).
3. Within the “Voice Only Line” page, simply enter the 10-digit Phone Number of the VOIP-500 Series
Phone/WEBS Paging Module and use the Extension field to provide the DTMF code as configured
earlier.
4. Click Save.
Otros manuales para VOIP-500 Series
2
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Teléfono de emergencia de Talkaphone
Talkaphone
Talkaphone ETP-MT/R Series Manual de usuario
Talkaphone
Talkaphone VOIP-600 Series Guía de configuración rápida
Talkaphone
Talkaphone VOIP-600 Series Manual de usuario
Talkaphone
Talkaphone ETP-MT Manual de usuario
Talkaphone
Talkaphone VOIP-500 Series Manual de usuario
Talkaphone
Talkaphone AOR-8 Manual de usuario
Talkaphone
Talkaphone ETP-400KE Manual de usuario
Talkaphone
Talkaphone VOIP-500 Series Manual de usuario
Talkaphone
Talkaphone VOIP-500 Series Manual de usuario
Talkaphone
Talkaphone ETP-100E Manual de usuario
Manuales populares de Teléfono de emergencia de otras marcas
Paso
Paso PA8506-V Manual de usuario
JNY Safetycare
JNY Safetycare FDC Manual de usuario
Rath
Rath 2100-TL9 Manual de usuario
Eldat
Eldat Easywave Fon Alarm Manual de usuario
Merak
Merak MMk-656 Manual de usuario
Assistive Technology Services
Assistive Technology Services TOUCH N TALK FD Instrucciones de montaje