Taiji TSK-110A Manual de usuario
Sake Warmer TSK-110A
TSK-210A
TSK-220A
TSK-420A
TSK-130A
TSK-230A
Operating Instructions
TSK-110A
TSK-130A
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOIS
TURE.
The lightning flash with arrowhead
symbol, within an equilateral trian-
gle, is intended to alert the user to
the presence of uninsulated "dan-
gerous voltage" within the prod-
uct's enclosure that may be of suf-
ficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and mainte-
nance (servicing) instructions in
the literature accompanying the
appliance.
The serial number of this product may be found on
the bottom of the unit.
You should note the serial number of this unit in
the space provided and retain this book as a per-
manent record of your purchase to aid identifica-
tion in the event of theft.
Model No.
Serial No.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SA 1965
SA 1966
Caution:
Before attempting to connect or operate this
product, please read the label on the bottom.
Introduction .................................................... 1
Use ................................................................. 1
Names of Parts .............................................. 2
Inspection and Preparation Before Use ......... 4
Instructions for Use ........................................ 7
After Use ...................................................... 12
After-Sales Service ...................................... 14
Specifications ............................................... 15
Contents
• To use your new purchase correctly and safely, you are advised to carefully read this manual and fully
understand it before use.
• Keep the manual at hand for quick reference after reading it.
• Be sure to receive your warranty of the product.
• The manual covers mainly safety precautions, the names of parts, instructions for use, after-sale service, and
product specifications.
• Failure to observe the precautions given in this manual may result in physical injuries. Exercise care not to
use your new product in a manner which does not conform to the instructions given herein.
Introduction
Use
This product is a sake warmer exclusively for indoor use. It is intended to make Japanese sake tasty, controlled to
a favorite temperature.
It should not be used for other purposes.
-1-
■Accessories
-2-
Names of Parts
TSK-110A
TSK-210A
TSK-220A
TSK-420A
2
3
3
6
1
1
1
1
1
1
1
1
Dispensing lamp
Water supply lamp
Power lamp
Power switch
Temperature indicator
lamp
Temperature setting switch
Sake drain lamp
Nozzle
Tray Server bottle holder
Water drain valve
exhaust port
Bottle holder funnel
Bottle holder (filter inside)
Air suction port
Water feeding port
Manual switch
Sake drain switch
Water level meter
HoseFunnelCap
<TSK-110A, 210A, 220A, 420A>
-3-
1
■Accessories
TSK-130A
TSK-230A 1
1
Joint hose
Water supply lamp
Power lamp
Power switch
Temperature indicator
lamp
Temperature setting
switch
Nozzle
Server bottle holder
Tray
Sake meter
Sake meter fittings
Sake meter mounting
screw
Sake meter mounting
metal
(* for TSK-130A only)
Air relief hole
Water feeding port
Dispensing lamp
Manual switch
Water level meter
Water drain valve,
exhaust port
Funnel
1
1
Hose
1
1
Valve A
1
1
Sake meter
1
1
Sake meter
fittings
1
-
Sake meter
mounting metal
4
2
Sake meter
mounting screw
1
Cleaning brush
1
1
Joint cap
<TSK-130A, 230A>
-4-
Inspection and Preparations Before Use
1.Check the instruction manual, and the accessories.
2.Choose a place for the sake warmer.
• A level, stable place.
• A well-ventilated place.
• A place away from heat sources, such as a gas burner and cooking range, and free from exposure to
direct sunlight. (Keep the sake warmer at least 50 cm away from them.)
• A place not so humid, not exposed to water.
3.Use an independent outlet.
Be sure to plug the power cable to an electrical outlet of 110 - 120V AC 15 A minimum or 220 - 240 V AC 7.5
A minimum, to which nothing else is connected.
4.Adjust the server bottle holder.
Loosen the server bottle holder screw, place your server bottle in the holder, adjust the server bottle holder up
or down so that the nozzle end will be about 2 cm in the server bottle.
(The machine automatically stops discharging the sake when the nozzle end touches the sake in the server
bottle.)
∗The nozzle may not work depending on the server bottle shape. Check it in advance.
<Fig. 1>
<Fig. 2>
-5-
<Fig. 3>
If you have a model TSK-110A, 210A, 220A, or 420A, go
to step 5.
If you have a model TSK-130A, or 230A, go to steps 6
and 7.
5.Clean the sake warmer heat
exchanger pipe. (Fig. 3)
This product is already cleaned inside before
shipment. When you are going to use it for the
first time or after a long period of non-use, clean it
according to the procedures specified below.
1) Push the power cord plug into a wall outlet.
2) Press the power switch to energize the
machine.
3) Take out the bottle holder funnel.
4) Feed water (approx. 70°C) to the bottle holder
to a degree not to cause overflow.
5) Press the manual button and take water from
the nozzle.
Water should be drained completely.
6) Put the bottle holder funnel on the bottle
holder.
Caution
• Hot water comes out of the nozzle while the inside
is cleaned. Pay attention to a possible accident of
scalding, etc.
6.Sake meter setting
• TSK-130A (Fig. 4) (Fig. 6)
1) Fix the accessory sake meter mounting metal to
the main body, using the accessory sake meter
mounting screws.
2) Fix the sake meter fittings to the sake meter
mounting metal, using the accessory sake meter
mounting screws. Then fit the sake meter.
* The sake meter can be mounted either on the
right or left of the main body.
3) Remove the cap that is attached to the sake
meter connection port.
4) Insert the joint part of the sake meter into the hole
located on the side surface of the main body, and
screw it in the sake meter connection port.
Leakage of sake will occur if this screw-in process
is awkwardly followed.
• TSK-230A (Fig. 5) (Fig. 6)
1) Fix the sake meter fittings perpendicularly to the
main body, using the accessory sake meter
mounting screws.
* The sake meter can be mounted either on the
<Fig. 4>
<Fig. 5>
-6-
right or left of the main body.
2) Fit the sake meter in the sake meter fittings.
3) Remove the cap that is attached to the sake meter
connection port.
4) Insert the joint part of the sake meter into the hole
located on the side surface of the main body, and
screw it in the sake meter connection port.
Leakage of sake will occur if this screw-in process
is awkwardly followed.
7.Clean the sake warmer heat
exchanger pipe.
This product is already cleaned inside before
shipment. When you are going to use it for the first
time or after a long period of non-use, clean it
according to “Daily maintenance” in the section of
“After use” herein.
Caution
• Hot water comes out of the nozzle while the inside
is cleaned. Pay attention to a possible accident of
scalding, etc.
<Fig. 6>
-7-
1.Push the power cord plug into a wall outlet.
2.Press the power switch.
When the “power switch” is pressed, the “power
lamp” is lit and the electric power begins to be fed.
At the same time, the “water supply lamp” is lit and
an alarm keeps sounding to indicate the “need for
water supply.”
3.Feed water or hot water to the water bath tank.
Use a funnel and feed water or hot water through
the water feeding port, to the level of “proper” at
the water level meter. (Fig. 7)
• The “proper” level corresponds to about 4.7
liters. (About 6.7 liters for the TSK-220A, TSK-
230A, and TSK-420A)
* When water is fed to the “lowest” level of the
water level meter, the “water supply lamp” and
the “alarm” go out. However, you should keep
feeding water to the “proper” level.
• In case of overfeeding, water will come out of
the exhaust port. In such a case, open the
water drain valve and discharge water to the
“proper” level.
• If water is too less, sake warming performance
will be lowered.
Caution
• Never feed any liquid other than water or hot
water.
4.Adjust the sake warming temperature.
1) When the “temperature setting switch” is
pressed once, the temperature setting mode is
assumed.
Initial setting is at [OFF].
• The setting indication and the sake warming
temperature are as specified below. However,
they can change under various conditions, and
they should be used as a guideline.
Lukewarm Approx. 45°C
Hot Approx. 65°C
2) Each time the “temperature setting switch” is
pressed once, the temperature indicator lamp
moves up from one after another along the
diagonal line. (Fig. 8)
Instructions for Use
<Fig. 7>
<Fig. 8>
(Hot)
(Lukewarm)
(OFF) (Temperature
setting)
-8-
3) If the switch is not pressed and such a
condition is kept unchanged for 5 seconds, the
mode is automatically switched over to the
“temperature display mode” and the
temperature in the tank is then displayed. (Fig.
9)
4) Until the preset temperature is attained, the
lamp flashes to indicate the present
temperature.
5) When the preset temperature is attained, all
the lamp up to the preset temperature are lit.
(As a guideline, when the HOT temperature is
preset, this temperature is attained in about 20
minutes for the TSK-110A, TSK-130A, and
TSK-210A, and in about 35 minutes for the
TSK-220A, TSK-230A, and TSK-420A.)
If you have a model TSK-110A, 210A, 220A or 420A, go
to steps 5 to 8.
If you have a model TSK-130A, 230A, go to steps 9 to 12.
5.Attach the accessory cap to an uncapped 1.8-liter
sake bottle. (Fig. 10)
Uncap a 1.8-liter sake bottle, and attach an
accessory cap to the bottle in its place.
6.Confirm that the nozzle has been pulled toward
you, and insert a 1.8-liter sake bottle in the bottle
holder funnel.
7.Dispense the warmed sake.
1) Fit the nozzle (sake outlet) into the mouth of
your sake server bottle, lightly push the bottle
until the nozzle is straight down, and place the
server bottle on the server bottle holder. (Fig.
11)
The dispensing lamp flashes and the warmed
sake begins to come out.
• Sake dispensing time is approximately 16
seconds for 180Pof hot sake.
• When the server bottle is filled with the
required volume of sake, the dispensing
operation stops automatically and the
dispensing lamp goes out.
2) You can pick up the server bottle in the
reverse procedure. Take out the bottle while
making its posture slantwise.
3) If you want to dispense the warmed sake
manually, press the “manual switch.” (Fig. 12)
While the switch is kept pressed, the sake
comes out.
• The warmed sake is dispensed even when the
nozzle is positioned slantwise.
Caution
• Sake from the nozzle is hot. Be careful for
handling.
<Fig. 9>
<Fig. 10>
<Fig. 11>
<Fig. 12>
<Dispensing>
<Manual>
<Sake drain>
(Hot)
(Lukewarm)
(OFF)
(Temperature
setting)
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Calentador de alimentos de Taiji
Taiji
Taiji HOTCABI Manual de usuario
Taiji
Taiji HS-03 Manual de usuario
Taiji
Taiji HC-6 Manual de usuario
Taiji
Taiji Ti-2 Manual de usuario
Taiji
Taiji HOTCABI HC-11UV Pro Manual de usuario
Taiji
Taiji HOTCABI HC-8 Manual de usuario
Taiji
Taiji TSK-N11R Manual de usuario
Taiji
Taiji HOT&COOL CONVERTIBLE CABI HC-11LX Pro Manual de usuario
Taiji
Taiji HC-12UVe Manual de usuario
Taiji
Taiji HOTCABI HC-38 Manual de usuario
