tagarno MOVE Manual de usuario
VERSION: 1.4.1 | FIRMWARE 7.60 | 2023-01-01
1
CONTENTS
1. INTENDED USE 2
2. WARNINGS 2
3. LASER POINTER WARNING 2
4. YOU HAVE RECEIVED 3
5. ASSEMBLING - MOVE 5
6. ASSEMBLING - MOVE UPGRADE KIT 8
7. CONNECTING 10
8. OPERATION 11
9. SETUP MENU 16
10. STANDARD APPS 23
11. ACCESS SAVED FILED 26
MANUAL | TAGARNO MOVE
12. SYSTEM UPDATE 27
13. LICENSE ACTIVATION 31
14. TECHNICAL SPECIFICATIONS 32
15. MAINTENANCE 36
16. WARRANTY 36
17. LICENSE AGREEMENT 36
18. ERGONOMICAL RECOMMENDATIONS 36
19. LABELS 37
20. DECLARATION OF CONFORMITY 38
21. COMPLIANCE STATEMENTS 39
2
WARNINGS
Read all safety information before you use the product.
Please pay attention when you see a warning label on the product.
This product is for indoor use only.
You must not discard this electrical/electronic product in domestic household waste.
Please dispose at your local recycling centre.
INTENDED USE
The product is a digital magnifying system consisting of a camera unit, PCBs, mechanical
parts and a power supply. The product is intended for marketing worldwide and is designed for
manual visual inspection.
1. Read the manual before you use the product
2. Use the product only as specied, or the protection supplied by the product can
be compromised
3. Do not position the equipment so that it is difcult to operate the disconnecting
device (appliance inlet of external power supply, equipment input connector)
4. If fluids are spilled on the product, turn the system off immediately by pulling the power
supply out of the electrical outlet
5. In case of re close to the product, please turn off and disconnect the system
6. Avoid subjecting the lens to sharp or hard objects
7. Please do not connect the product, if visible damages appear
8. Do not dismantle any parts of the product, except where noted in the manual
9. Never disassemble or clean internal optical surfaces
10. Use only the power supply provided from TAGARNO
11. Always turn off the system before unplugging, when possible
The product is a digital magnifying system consisting of a camera unit, Power box, mechanical
parts and power supplies. The product is intended for marketing worldwide and is designed for
manual visual inspection.
1. INTENDED USE
2. WARNINGS
3. LASER POINTER WARNING
This product is equipped with a red laser pointer to enable easy alignment of the
camera and areas of interest during the inspection process.
This product is a Class 2 laser product that complies with IEC60825-1 international
standard for lasers.
CAUTION
Follow these safety instructions when using the product.
• Never look directly into the laser aperture
• Do not point towards anyone deliberately
• Leave the laser on only when necessary
• Always turn off power during service and maintenance
• Service may only be performed by trained personnel
appointed by TAGARNO
This label is placed near the laser aperture
The label below is placed on the camera head
3
Please note that the content of your delivery will vary depending on whether you have purchased a complete MOVE microscope or
a MOVE Upgrade kit to an existing ZAP microscope.
RECEIVED WHEN PURCHASING MOVE AS A COMPLETE MICROSCOPE
DELIVERY (1/2)
USB memory stick
Power box Power supply for Power
box
XPLUS FHD control box
4. YOU HAVE RECEIVED
HDMI - HDMI cable Hex keys
HandlesFlex arm advanced Power supply
Camera head with lens
and cables
Smart guide
Finger screw
Height adjustment wheels
Cable holder
SMART GUIDE
4
USB memory stick
Power box Power supply for Power
box
XPLUS FHD control box
Smart guide Height adjustment wheels
HDMI - HDMI cable Hex keys
RECEIVED WHEN PURCHASING A MOVE UPGRADE KIT
DELIVERY (2/2)
SMART GUIDE
5
5. ASSEMBLING - MOVE
ASSEMBLING | MOVE (1/3)
Mount the table mount using the table clamp. Assemble the
bottom of the flex arm and the table mount.
NB: For maximum stability at all magncation levels, make sure to
mount the microscope on a sturdy table.
NB: If you are purchasing a MOVE Upgrade kit for
an existing ZAP, we refer to the next section.
Mount the height adjustment wheels to the camera head with two
of the four provided screws. Then, adjust the position of the height
adjustment wheels and secure them to the camera head with the
two remaining screws.
Mount the microscope to the top of the flex arm using the vesa
bracket, screws and handles.
6
ASSEMBLING | MOVE (2/3)
To increase stability, adjust the flex arm weight with the
included allen key. Turn it clockwise to decrease stability or
counterclockwise to increase stability.
Press the cables into place in the slot on the flex arm and secure
them by screwing the cable holder into place on top.
Tighten the 3 pinol screws to remove slack.
Assemble the flex arm by slotting the two arms together.
1
2
3
7
Then, use the included nger screw to lock vertical movement.
ASSEMBLING | MOVE (3/3)
IMPORTANT U.S. only information: Laser beam attenuator mounted.
Unmount lens protection cap when using this microscope.
For extra stability in locked positions, remove the rubber covering
on the side of the flex arm.
8
6. ASSEMBLING - MOVE UPGRADE KIT
ASSEMBLING | MOVE UPGRADE KIT (1/2)
Release the cables from the flexarm by unscrewing the cable
holder.
Unmount the microscope from the flexarm by unscrewing the four
screws on the back of flexarm head. This will also unmount the
handles.
Disassemble the flexarm by pulling the two arms apart.
Unmount the camera head from the vesa bracket by unscreweing
the four screws on the back of the vesa bracket.
9
Mount the microscope to the top of the flex arm using the vesa
bracket, screws and handles.
Assemble the flex arm by slotting the two arms together. Press the cables into place in the slot on the flex arm and secure
them by screwing the cable holder into place on top.
ASSEMBLING | MOVE UPGRADE KIT (2/2)
Mount the height adjustment wheels to the camera head with two
of the four provided screws. Then, adjust the position of the height
adjustment wheels and secure them to the camera head with the
two remaining screws.
10
7. CONNECTING
Connect cables in the order below.
ESD grounding cable
Connect cable from camera head
to grounding outlet
Cable length = 3.180mm.
USB 3.0 cable
Connect cable from camera head
to (any) power box USB 3.0 output
Cable length = 2.800mm.
HDMI Standard Type cable
Connect cable from power box
to monitor
Cable length = 2.000mm.
DisplayPort Full Size cable
Connect cable from power box
to monitor (cable not included)
HDMI cable (obsolete)
Obsolete when using MOVE
(dedicated for TAGARNO ZAP)
Cable length = 2.780mm.
Control box XPLUS cable
Connect cable from control
box to power box
Power supply cable (Power box)
Connect cable from power box
to power socket
Control box XKEY cable (obsolete)
Obsolete when using the MOVE
(dedicated for TAGARNO ZAP)
Cable length = 3.030mm.
Ethernet cable
Connect cable from power box
to ethernet wall socket
(if needed)
Cable length = 3.000mm.
Power supply cable (camera head)
Connect cable from camera head
to a power socket
Power cable length = 3.050mm.
Power supply cable length = 1.600mm.
Note regarding
monitor connection
If DisplayPort is used, the
HDMI cable becomes obsolete.
or
1
2
3
4
5
6
7
Foot switch
Connect cable from control box
to foot switch and from foot switch
to power box
⎓
⎓
⎓
⎓
5A
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Lupa de tagarno
