Swisher WB942 Manual de usuario

THE FINISHING TOUCH

42” FINISH CUT MOWER SELF PROPELLED

WALK BEHIND

OWNER’S

MANUAL

1602 CORPORATE DRIVE, P.O. BOX 67, WARRENSBURG , MISSOURI 64093

PHONE (660) 747-8183 FAX (660) 747-8650

MODEL NO.

Manufacturing quality lawn care equipment since 1945

Assembly

Operation

Service and Adjustment

Repair Parts

Made In The

USA

Rev.04-083

Read and follow all Safety

Rules and Instructions

before operating this

equipment.

WB942

Visit us at: www.swisherinc.com

ONWB942

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is: This product is free from

defects in materials and workmanship for a period of one (1) year from the date of purchase by

the original consumer purchaser. We will repair or replace, at our discretion, parts found to be

defective due to materials or workmanship. This warranty is subject to the following limitations

and exclusions:

1) Engine Warranty All engines utilized on our products have a separate warranty

extended to them by the individual engine manufacturer. Any

engine service difficulty is the responsibility of the engine

manufacturer and in no way is Swisher Mower Co., Inc. or its

agents responsible for the engine warranty. The Briggs & Stratton

Engine Service Hot-Line is 1-800-233-3723. The Tecumseh

Engine Service Hot-Line is 1-800-558-5402.

2) Commercial Use The warranty period for any product used for commercial or rental

is limited to ninety (90) days from the date of original purchase.

3) Limitations This warranty applies only to products which have been properly

assembled, adjusted, and operated in accordance with the

instructions contained within this manual. This warranty does not

apply to any product of Swisher Mower Co., Inc., that has been

subject to alteration, misuse, abuse, improper assembly or

installation, shipping damage, or to normal wear of the product.

4) Exclusions Excluded from this warranty are normal wear, normal adjustments,

and normal maintenance.

In the event you have a claim under this warranty, you must return the product to an authorized

service dealer. All transportation charges, damage, or loss incurred during transportation of parts

submitted for replacement or repair under this warranty shall be borne by the purchaser. Should

you have any questions concerning this warranty, please contact us toll-free at 1-800-222-8183.

The model number, serial number, date of purchase, and the name of the authorized Swisher

dealer from whom you purchased the mower will be needed before any warranty claim can be

processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME

PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not

allow the limitation of consequential damages or limitations on how long an implied warranty

may last, so the above limitations or exclusions may not apply to you. This warranty gives you

specific legal rights and you may have other rights, which vary from state-to-state. This is a

limited warranty as defined by the Magnuson-Moss Act of 1975.

SAFETY PRECAUTIONS AND DECALS

• Read the manual. Learn to operate this machine safely.

• Always disconnect the spark plug wire and place the wire where it cannot contact

the spark plug, to prevent accidentally starting the engine when setting up,

transporting, adjusting or making repairs.

• Keep all shields and guards in place.

• Understand the speed, steering and stability of this machine. Know the positions

and operations of all controls before you operate this machine. Check all of the

controls in a safe area before starting to work with this machine.

• Allow only responsible adults who are familiar with these instructions to operate

this machine. Never allow children to operate this machine.

• Clear the area of objects such as rocks, toys, wire, etc. that can be picked up and

thrown by the blade.

• Be sure the area is clear of other people before mowing. Be aware of the mower

discharge direction and do not point at anyone. Stop the machine if anyone enters

the mowing area. Children are often attracted to the machine and the mowing

activity. Never assume that children will remain where you last saw them.

Keep children under the watchful care of another responsible adult.

• No riders!

• Do not put hands or feet near or under rotating parts. Keep clear of the discharge

opening at all times.

• Do not mow in reverse. Always look down and behind before and while backing.

• Turn off the blades when not mowing. Before leaving the machine, turn off the

blades and stop the engine.

• Watch for traffic when operating near or crossing roadways.

This Safety Alert Symbol indicates important messages in this

manual. When you see this symbol, carefully read the message that

follows and be alert to the possibility of personal injury.

Read this manual completely. This machine is capable of amputating hands and

feet, and throwing objects. Failure to observe the following safety instructions could

result in serious injury or death.

• Turn off the blades when not mowing. Before leaving the machine, turn off the

blades and stop the engine.

• Watch for traffic when operating near or crossing roadways.

• Do not operate the mower if it has been dropped or damaged in any manner or if

the mower vibrates excessively. Excessive vibration is an indication of damage.

Repair mower as necessary.

• Dress properly. Do not operate the mower when barefoot or wearing open

sandals. Wear only solid shoes with good traction when mowing.

• Do not operate the machine while under the influence of alcohol or drugs.

• Operate self-propelled machines up and down slopes. There is significant risk of

overturns when operating across slopes. Operate walk-behind machines across

slopes. There is a significant risk of slipping under a walk-behind machine when

operating up and down slopes.

• Never tamper with safety devices. Check their proper operation regularly.

• Stop and inspect the equipment if you strike an object. Repair, if necessary,

before restarting.

• Never make adjustments or repairs with the engine running.

• Mower blades are sharp and can cut. Wrap the blades or wear gloves, and use

extra caution when servicing them.

SAFETY AND OPERATIONAL DECALS

Replace decal immediately if damaged. Order by part number from Swisher Mower and Machine Co. Inc.

OD30 – WARNING DECAL

OD29 – SPINNING BLADE DECAL

OD43 – FLYING DEBRIS DECAL

OD36 – DEFLECTOR DECAL

OD55 – DANGER DECAL

The operation of any cutter can produce foreign objects to be thrown into the

eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-

vision safety goggles before starting any cutting machine and while operating such

a machine.

The operation of any cutter produces sound waves that are damaging to the

human ear. Ear protection is recommended.

CAUTION!

Tragic accidents can occur if the operator is not alert to the presence of

children. Children are often attracted to the machine and the mowing

activity. Never assume that children will remain where you last saw them.

OPERATING YOUR NEW CUTTER

SERVICE AND ADJUSTMENTS

BELTS CONFIGURATION

Stop engine, let all moving parts come to a complete stop. Disconnect spark plug.

TRANSMISSION BELT

BLADE SPINDLE

BELT

BLADE DRIVE BELT

BLADE SPINDLE BELT REPLACEMENT

REMOVAL

•Stop engine, let all moving parts come to acomplete stop. Disconnect spark

plug.

•Remove belt cover.

•Remove Blade Drive Belt. (See Blade Drive Belt replacement.)

•Pull tension idler away from Blade Spindle Belt to relieve tension.

• Remove belt.

INSTALLATION

•Pull tension idler away from belt.

•Install belt according to above configuration.

•Install Blade Drive Belt as shown.

• Install belt cover and tighten hardware.

BLADE DRIVE BELT REPLACEMENT

REMOVAL

•Stop engine, let all moving parts come to acomplete stop. Disconnect spark

plug.

•Disengage all blade controls by releasing the bails.

•Remove belt cover.

•Rotate belt off pulleys and pull belt through motor belt guide.

INSTALLATION

•Route belt as shown.

•Adjust engage idler tension. Belt should be snug during engagement of blade

latch. Too much tension will not allow the blade latch to function properly.

•Tighten nuts on blade engage cable when finished.

•Install belt cover and tighten hardware.

WHEEL DRIVE BELT REPLACEMENT

REMOVAL

•Stop engine, let all moving parts come to acomplete stop. Disconnect spark

plug.

•Remove belt cover.

•Remove Blade Drive Belt, (See “Blade Drive Belt replacement”)

•Locate belt guide for wheel drive belt and loosen.

• Remove wheel drive belt.

INSTALLATION

•Install belt as shown.

•Adjust belt guide snug against motor pulley and back off ? ”.

•Tighten belt guide hardware.

• Install Blade Drive Belt (see “Blade Drive Belt installation”).

• Install belt cover and tighten hardware.

WHEEL BRAKE ADJUSTMENT

Adjustment may be necessary if the unit does not stay in position on ahill with the

operator bails released, or if the brake drags while in neutral with the “GROUND

CONTROL” bail engaged.

PROCEDURE

•Stop engine, let all moving parts come to acomplete stop. Disconnect spark

plug.

•Release “GROUND CONTROL” bail.

•Adjust nuts forward or backward. When the “GROUND CONTROL” bail is

disengaged there should be constant tension on the brake arm.

•All tension should be off brake arm when “GROUND CONTROL” bail is

engaged.

• Tighten adjustment nut when finished and re-attach spring, if necessary.

WHEEL DRIVE BELT ADJUSTMENT

Adjustment may be necessary if loss of traction occurs due to belt slippage.

PROCEDURE

•Adjust “GROUND CONTROL” cable in or out to achieve maximum traction.

•Too much tension will not allow the “GROUND CONTROL” bail to fully

activate.

• Too little tension will allow the belt to slip, resulting in loss of traction.

• “GROUND CONTROL” bail should fully close against handlebars when

functioning properly.

Adjust Nuts

Check for loosened bolts, nuts,

springs, etc. often. Replace

filters, spark plugs as needed.

Keep blades in good working

order.

OVERALL ASSEMBLY

When ordering painted parts, please indicate with

corresponding letters: C = Red Parts

TK = Textured Black Parts

REPLACEMENT PARTS

When ordering painted parts, please indicate with corresponding letters: C = Red Parts;

TK = Textured Black Parts (ex. 4207TK, 4237C)

Item # Description Part # Item # Description Part #

1 Motor Base 4270 46 Tension Spring 682S

2 Wire Link BRS6H 47 1/2 x19/16 Shoulder Bolt NB220

3 Link Spring T2SM 48 5/16 SAE Washer NB275

4 5/16-18 Serrated Flange Nut NB170 49 3/8-16 Grade 2Nut NB212

5 5/16-18 x21/2 Grade 5Bolt NB138 50 5/16-18 Nylock Nut NB181

6 Shift Linkage 4282 51 Tension Idler Kit 4263

7 Blade Driver Housing B99 52 Blade Engage Pulley 7509

8 Brake Spring BT297 53 Blade Drive Belt 4220

9 Brake Pad BP370 54 Blade Spindle Belt 4219

10 Blade Engage Idler 4262 55 Wheel Drive Belt 2414

11 1/2 -13 Nut NB213Z 56 Transmission Belt Guide 2451

12 Brake Pad Clip BP370S 57 1/4-20 Flange Nut NB524

13 5/16 Flat Washer NB556 58 Blade Drive Belt Guide 4234

14 3/8 -16 2-way Locknut NB280 59 8HP B&S Engine N/A

15 5" Chain Links AS080 60 Upper Engine Spacer 689L

16 3/8-16 x2Grade 2bolt NB231 61 1/4 x1/2 Key Stock 4258

17 1/2-13 x5Grade 5bolt NB155 62 Upper Engine Pulley 2411

18 Blade Engage Idler Kit 4280 63 Lower Engine Spacers BB105SL

19 1/8 x1Cotter Pin NB126 64 1/4 x1Key Stock 9031

20 Center &Left Blade Driver Kit 9080 65 Lower Engine Pulleey 688

21 Blade Bearing B98 66 Belleville Washer 699

22 Center &Left Blade Shaft 9075 67 7/16-20 x11/2 Grade 5Bolt NB637

23 Washer B98W 68 Height Adjust Arm 4275

24 1/4-20 x1Grade 5Bolt NB250 69 Front /Rear Torsion Connector 4235

25 1/4-20 Nylock Nut NB180 70 Front Torsion Bar 4233

26 15" Blade 4221 71 Rear Torsion Bar 4236

27 Serrated Belleville Washer NB607 72 3/4 x18 GA Washer NB179

28 3/8 -24 x11/4 Grade 5Bolt NB166 73 5/16-18 x3/4 Serrated Flange Bolt NB596

29 Blade Mounting Plate 9008 74 Plastic Belt Cover 4257

30 3/8-24 2Way Lock Nut NB216 75 3/8-16 x3Eye Bolt NB635

31 3/8-24 x1Grade 5Bolt NB238N 76 3/8-16 Nylock Nut NB182

32 Lower Blade Pulley B4104 77 Front Tire &Wheel 4218

33 Pulley Spacer 6104RS 78 Caster 4266

Upper Blade Pulley (Center &Left Only)

B104 79 5/8 x10 GA Washer NB149

35 3/4-16 2Way Lock Nut NB629 80 5/8 Flanged Bearing F157B

36 Right Blade Shaft 9077 81 Grass Chute 4261

37 Right Blade Driver Kit 9079 82 5/16-18 x81/2 Grade 2Bolt NB136

38 Transmission Idler Pulley B27 83 Grass Chute Spring CH5S

39 Transmission Idler 4276 84 Plastic Roller AS001

40 3/8-16 x11/2 Grade 5Bolt NB107 85 5/16-18 x51/2 Grade 5Bolt NB521

41 1/2-13 x21/2 Grade 5Bolt NB588 86 1/2 x14 GA Washer NB177

42 3/8 SAE Washer NB272 87 5/16-18 x4Carriage Bolt NB101

43 Transmission Idler Kit 4281 88 Hanger Bracket 4216

44 Tension Idler Pulley B527 89 1/2-13 2Way Jam Lock Nut NB121

45 Tension Idler 6681 90 Rear Tire &Wheel 4217

Tabla de contenidos

Otros manuales de Cortacésped de Swisher

Swisher

Swisher Predator WB924 Manual de usuario

Swisher

Swisher QuadBoss COMMERCIAL PRO QBFC14560CP Manual de usuario

Swisher

Swisher POL1250F Manual de usuario

Swisher

Swisher ZT13536, ZT17542B, ZT20050 Manual de usuario

Swisher

Swisher TWR10532BS Manual de usuario

Swisher

Swisher FC1966BS Manual de usuario

Swisher

Swisher Predator WB80024 Manual de usuario

Swisher

Swisher ZT2452 Manual de usuario

Swisher

Swisher T1360B1 Manual de usuario

Swisher

Swisher Predator Talon WBERC11524C Manual de usuario

Swisher

Swisher ZT2760 BP Manual de usuario

Swisher

Swisher Z-MAX ZT2560 Manual de usuario

Swisher

Swisher RT1250E Manual de usuario

Swisher

Swisher WBERC11524 Manual de usuario

Swisher

Swisher ZT2760A Manual de usuario

Swisher

Swisher The Predator WB11524 Manual de usuario

Swisher

Swisher ZT2760B Manual de usuario

Swisher

Swisher TRAILMOWER POL14560X Manual de usuario

Swisher

Swisher RT10544, RT80044 Manual de usuario

Swisher

Swisher ST50022STDQ Manual de usuario

Swisher

Swisher ZTR2760BS Manual de usuario

Swisher

Swisher QUADBOSS QBFC1966 Manual de usuario

Swisher

Swisher ZT2452A Manual de usuario

Swisher

Swisher T2066 Manual de uso y cuidado

Manuales populares de Cortacésped de otras marcas

RHINO

RHINO 1958 Manual de usuario

Wolf Garten

Wolf Garten Compact plus 40 B Manual de usuario

Cub Cadet

Cub Cadet LTX 1045 Manual de usuario

Craftsman

Craftsman 917.378461 Manual de usuario

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manual de usuario

Challenge

Challenge CH18V2 Instrucciones de operación

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manual de usuario

DEWEZE

DEWEZE ATM-725 Manual de operación

Weed Eater

Weed Eater 180083 Manual de usuario

Husqvarna

Husqvarna Poulan Pro PP185A42 Manual de usuario

Better Outdoor Products

Better Outdoor Products Quick Series Manual de usuario

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manual de funcionamiento

MTD

MTD 795, 792, 791, 790 Manual de usuario

Toro

Toro Groundsmaster 3505-D Manual de usuario

Dennis

Dennis FT 610 Manual de usuario

AIRFORCE

AIRFORCE F-15 Gen 3 Manual de usuario

MTD

MTD 126-220-000 Manual de usuario

Toro

Toro 74806 Manual de usuario