Swiftpoint 500 Manual de usuario
INSTRUCTION BOOKLET
English - Quick Start Guide
Product Disposal
Please dispose of this product and packaging in a responsible manner and in
accordance with any applicable local or national disposal regulations, including those
governing the recovery and recycling of waste electrical and electronic equipment
(WEEE).
Federal Communication Commission Interference Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna
-Increase the separation between the equipment and receiver
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
-Consult the dealer or an experienced radio/TV technician for help
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this
equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
The product complies with the FCC portable RF exposure limit set forth for an uncontrolled environment and is safe for intended
operation as described in this manual.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended
operation as described in this manual. Europe EU Declaration of Conformity.
0560 - Europe - EU Declaration of Conformity
This device complies with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. The following test methods
have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
EN 60950-1: 2006/A2:2013
Information technology equipment - Safety - Part 1: General requirements
EN 62479: 2010
Assessment of the compliance of low power electronic and electrical equipment with the basic restrictions related to human exposure to
electromagnetic fields (10 MHz to 300 GHz)
EN 300 440-1 V1.6.1 (2010-08)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40
GHz frequency range; Part 1: Technical characteristics and test methods
EN 300 440-2 V1.4.1 (2010-08)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40
GHz frequency range; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
EN 301 489-1 V1.9.2: 2011
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment
and services; Part 1: Common technical requirements
EN 301 489-3 V1.6.1: 2013
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment
and services; Part 3: Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and 246 GHz
The technical documentation as required by the Conformity assessment procedure is kept at the following address:
Swiftpoint Limited, 77 Montreal Street, Christchurch 8023, New Zealand
Gesture Mouse
Model: 500
0560 0560
FCC ID X8Y500
IC: 9094A-500
Rating: 5V , 130mA
Designed in New Zealand
Made in China
www.swiftpoint.com
Dongle
Model: 501
FCC ID X8Y501
IC: 9094A-501
Rating: 5V , 130mA
Designed in New Zealand
Made in China
www.swiftpoint.com
201-150172
R201-150190
R
Quick Start Guide
USB charger/
receiver
OFF
CONFIG
ON
Stylus
Scroll wheel
Docking
point
Switch
Left-click (front)
Right-click
(rear)
Tilt mouse upward
to engage stylus
Thumb grip
LED
Middle finger
grip (hidden)
Charging the Mouse
Connecting the Mouse via USB Receiver
1.
2.
The battery LED will flash while charging and turn off once
fully charged. A full charge can take up to 90 minutes.
To begin using the mouse, move the switch on the underside
to the ON position
To charge your Swiftpoint GT:
Plug the USB charger into a USB port on your computer
or into a USB charging accessory
Dock the mouse onto the charger
To connect via the USB charger/receiver, plug the USB charger/receiver into a port
on your computer and move the switch on the underside of the mouse from the
OFF to the ON position. The mouse will automatically connect to your computer.
Connecting the Mouse via Bluetooth 4.0
Once the mouse is fully charged, you can pair it to your computer via Bluetooth 4.0.
Remove the USB charger/receiver. Leave the mouse OFF for the first steps.
1. Go to Bluetooth device menu in your system settings
- Windows: Settings > Devices > Bluetooth
- MacOS: System Preferences > Bluetooth
2. Ensure Bluetooth is switched on
3. Remove any existing “Swiftpoint GT” in the list by selecting it, then selecting
Remove
4. While holding down either mouse button, move the switch on the underside of the
mouse to ON. The LED will flash to indicate pairing mode
Recharging
5.
If "SwiftpointGT" does not appear make sure your system supports Bluetooth 4 and
it is switched on.
Please note that Windows 7 does not support Bluetooth 4.0
Note:
If you connect your Swiftpoint GT via Bluetooth, you can plug the USB charger/reciev-
er into a USB charging accessory rather than using one of your computers USB
ports.
When not using the mouse for brief periods, dock the mouse on the USB charger so
it maintains a charge. The first 30 seconds of charging will give you up to one hour of
use. ht gniruDof use.When not using the mouse for extended periods, move the
switch on the underside of the mouse to OFF.
When “Swiftpoint GT” appears in the list of searched devices, click on the
device name to install and pair with the device
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Ratón de Swiftpoint
