SVS SoundPath Manual de usuario

PB-2000 SB-2000

POWERED SUBWOOFERS

Subwoofer Isolation System

OWNER’S MANUAL

Thank you, and congratulations on purchasing your new

SVS SoundPath Subwoofer Isolation System!

The SVS SoundPath Subwoofer Isolation System decouples and isolates the

subwoofer from the ﬂooring, resulting in tighter and cleaner sounding bass, less

buzz/rattle in the room, and fewer complaints from adjacent neighbors in apartments

and townhouses. It’s the next best thing to sound-prooﬁng!

The SoundPath Subwoofer Isolation System works with any brand of subwoofer

which accepts screw-in feet. Developed with extensive accelerometer and acoustic

measurements, this system features optimized durometer elastomer feet which

signiﬁcantly reduce ﬂoor vibration.

Our Sound Experts in Customer Service can assist you with installing the SoundPath

Subwoofer Isolation System, so please don’t hesitate to contact Customer Service if

you need guidance.

If you have any questions about your SVS product, please contact us directly.

www.svsound.com • [email protected] • (877) 626-5623

owner’s manual v. 2.0_01102017 1

TABLE OF CONTENTS

PACKAGE CONTENTS 3

INSTALLATION 4

CABINET / BOX STYLE SUBWOOFERS

4

SVS CYLINDER SUBWOOFERS – BASE PLATE RETAINED 5

SPECIFICATIONS 6

SHARE YOUR THOUGHTS 6

2

PACKAGE CONTENTS

Package Contents:

4 Foot System:

• Four (4) SoundPath Isolation Elastomer Feet with Steel Outer Shell

• Four (4) ¼-20 x 16 mm screws

• Four (4) M6 x 16 mm screws

• Four (4) M8 x 16 mm screws

6 Foot System:

• Six (6) SoundPath Isolation Elastomer Feet with Steel Outer Shell

• Six (6) ¼-20 x 16 mm screws

• Six (6) M6 x 16 mm screws

• Six (6) M8 x 16 mm screws

3

¼-20 x 16 mm

M6 x 16 mm

M8 x 16 mm

SoundPath Isolation

Elastomer Feet

INSTALLATION CABINET / BOX STYLE SUBWOOFERS

Cabinet / Box Style Subwoofers:

1. Place padding such as a soft blanket on the ﬂooring to protect the ﬁnish of the

subwoofer.

2. Using a helper (if needed), carefully place the subwoofer cabinet on its side or top,

resting on the blanket. Take care to avoid damaging the ampliﬁer. Important Notice: When

moving the subwoofer, do not allow the weight of the cabinet to place an excessive lateral

(sideways) load on the feet. This may damage the feet, the threaded insert or the cabinet.

3. Unthread and remove the subwoofer's original equipment (OE) feet.

4. Gather all of the 16 mm long machine screws from the Isolation System kit. There are

three (3) thread sizes provided – ¼-20, M6 and M8.

5. Compare the OE feet machine screws to the 16 mm long Isolation System machine

screws. Select the matching/correct thread size (SVS cabinet subwoofers utilize the ¼-20

thread size).

6. Once you have selected the correct thread size, install the Isolation feet by inserting

the 16 mm long machine screw through the bottom opening of the rubber foot, through the

opening in the steel outer shell, and into the threaded insert of the subwoofer cabinet.

7. Make sure the machine screw is

correctly aligned and does not cross-thread.

8. Hand-tighten snugly. Avoid

over-tightening, which might damage the

threaded insert or the cabinet.

9. Using a helper (if needed) carefully lift

the subwoofer cabinet and place it directly

down onto the installed Isolation feet. Take

care to avoid damaging the ampliﬁer.

Important Notice: When placing the subwoofer back

into position, do not allow the weight of the cabinet

to place an excessive lateral (sideways) load on the

Isolation feet. This may damage the Isolation feet, the

threaded insert or the cabinet.

Important Notice: - Do not drag the subwoofer cabinet across the ﬂooring with the Isolation feet installed. This may

damage the Isolation feet, the threaded insert or the cabinet. If you need to move the subwoofer, always lift (use a

helper if needed) the subwoofer and then place it into the new location.

4

5

INSTALLATION SVS CYLINDER SUBWOOFERS

SVS Cylinder Subwoofers:

1. Using a helper as needed, lay the cylinder subwoofer sideways on a stable surface.

Take care to avoid damaging the ampliﬁer.

2. Peel off the original equipment (OE) rubber disc feet.

3. Only remove one (1) OE machine screw at a time.

This will prevent the base plate from dislodging.

Important Notice: - If you are using a powered bit driver

to remove and/or install the machine screws, avoid

excessive downward pressure on the screw, as that may

dislodge the t-nut mounted to the backside of the

woofer end-cap.

4. Install the Isolation foot by inserting the OE

machine screw through the bottom opening of the

rubber foot, through the opening in the steel outer shell,

through the base plate, through the dowel (re-aligning

the dowel as necessary) and into the t-nut on the

backside of the woofer end-cap.

5. Make sure the machine screw is correctly aligned

and does not cross-thread.

6. Tighten the OE machine screw avoiding excessive

downward pressure. Once the screw fully tightens and

starts to pull against the end-cap t-nut, tighten securely

using hand-pressure.

7. Using a helper (if needed), carefully stand the

cylinder subwoofer back onto the installed Isolation

feet. Take care to avoid damaging the ampliﬁer.

Important Notice: - Do not drag the subwoofer base plate across the

ﬂooring with the Isolation feet installed. This may damage the Isolation

feet or the base plate. If you need to move the subwoofer, always lift (use

a helper if needed) the subwoofer and then place it into the new location.

SPECIFICATIONS

Materials Of Construction:

• Durable Anodized Steel Outer Shell

• Elastomer Foot with Optimized Durometer

• Steel Machine Screws

SoundPath Isolation Feet Dimensions:

• Overall Height: 40 mm

• Shell Diameter: 58 mm

• Foot Diameter: 53 mm

• Screw Engagement Depth: 9 mm (applies to 16 mm length screws)

SHARE YOUR THOUGHTS

Our SVS Sound Experts are standing by from Monday to Friday form 9AM-9PM ET, Saturday

from 12PM-6PM, and Sunday from 12PM-4PM to assist you with subwoofer set-up and

optimization, AV Receiver settings and more. They can be reached by phone, email or chat

via the options below.

www.svsound.com • [email protected] • (877) 626-5623

We also invite you to share a review on our website and to join our fun and active social

media community where we share reviews, featured systems, interesting audio articles and

more.

6

Post at facebook.com/SVSound Tweet @SVS_Sound

Follow instagram.com/SVS_Sound

................................................................................................................................................

NOTES

7

................................................................................................................................................

NOTES

8

SVS

260 Victoria Rd.

Youngstown, Ohio 44515

United States

(877) 626-5623

www.svsound.com

SVS SoundPath Manual de usuario

Manuales populares de Subwoofer de otras marcas