Suzuki C10 Hoja de instrucciones
1
C10 Color Display
Conguration Manual
P/N 99954-62016
2
All information, illustrations, photographs and
specications contained in this book are based on
the latest product information available at the time
of publication.
Produced by Suzuki Motor of America, Inc.
Technical Publications & Training
Issue Date: June 2016
3
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . 4
Single Engine Conguration . . . . . . . . . . . . . . 4
Initial Power-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Select a Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Set the Time and Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Select the Units to be Displayed . . . . . . . . . . . . . . . . . . . . . . . . . 6
Vessel Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Engine Display Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Warning Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Congure Devices on the Network . . . . . . . . . . . . . . . . . . . . . . . . 8
Using the Auto Select Function . . . . . . . . . . . . . . . . . . . . . . . . . 10
Conguring the Fluid Level Sensor . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Calibrating the Fuel Level Sensor. . . . . . . . . . . . . . . . . . . . . . . . 15
GPS Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Suzuki Engine Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setting Up a Custom Page . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Dual Engine Conguration . . . . . . . . . . . . . . .25
Initial Power-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Select a Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Set the Time and Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Select the Units to be Displayed . . . . . . . . . . . . . . . . . . . . . . . . 27
Vessel Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Engine Display Conguration . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Warning Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Congure Devices on the Network . . . . . . . . . . . . . . . . . . . . . . . 31
Conguring the Fluid Level Sensor . . . . . . . . . . . . . . . . . . . . . . . 36
Setting the Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Calibrating the Fuel Level Sensor. . . . . . . . . . . . . . . . . . . . . . . . 39
GPS Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Using the Auto Select Function . . . . . . . . . . . . . . . . . . . . . . . . . 42
Setting Up a Custom Page . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Notes. . . . . . . . . . . . . . . . . . . . . . . . . . .51
4
Single Engine Conguration
This section shows you how to congure a single
engine conguration using one (1) C10 Color
Display kit, a uid level sensor and a GPS.
This is a typical conguration for a single-engine
conguration. You may choose to congure your
vessel differently, and add or reduce the number of
accessories.
Initial Power-Up
NOTE:
The C10 should be connected to a single cable or
Suzuki Precision Control (SPC) motor, and then be
powered up. It is now ready for conguration.
Once the C10 Color Display is turned ON, the
Suzuki “S” logo appears. The C10 then takes 25 –
30 seconds to power-up to the rst screen.
Select a Language
The rst screen to appear is the Select Language
screen.
1. Use the arrow buttons to select the proper
language, then press Enter.
C10 Color Display Conguration Manual
Introduction
This manual is designed to guide you through the most common single-engine and dual-engine congurations
of the Suzuki C10 Color Display. Notably, once you learn how to congure a dual-engine set-up on the C10,
you will also be able to congure three-engine and four-engine set-ups.
If you are a Suzuki Marine Dealer: Suzuki Motor of America, Inc. (SMAI) encourages you to review the
C10 E-Learning Module that is available on Suzuki ServicePRO (www.suzukiservicepro.com). This module
provides you with step-by-step instructions for installing a C10 on a vessel.
If you are a Suzuki customer: Please see your Suzuki Marine Dealer for questions you may have about
installation and conguring the C10 Color Display. To locate your Suzuki Marine Dealer, go to www.suzukima-
rine.com and click on the FIND A DEALER tab at the top of the homepage.
5
Set the Time and Date
NOTE:
With a GPS installed, the local time offset is
automatically populated.
1. To set the time and date manually, use the
arrow buttons to select Time format, then
use the arrow buttons to select the 12-hour or
24-hour time format and press Enter.
2. Use the arrow buttons to select Date format,
then set the date and press Enter.
NOTE:
A GPS antenna must be connected in order for the
date to be accurate.
6
3. After setting the time and date, conrm the
information is correct, then select Next and
press Enter.
Select the Units to be Displayed
On the Units screen, use the arrow buttons to
select how you want the units to be displayed on
the C10, then press Enter.
Vessel Set-up
1. On the Vessel Set-up screen, the C10 will
default to one engine and one fuel tank.
If you are only setting up the C10 for a single
fuel tank, use the arrow buttons to select
Total Fuel Capacity.
NOTE:
It is possible to select up to eight engines, but only
two engines can be displayed at any time on the
C10 Color Display.
7
2. Use the arrow buttons to set the fuel capacity
and press Enter.
3. After conrming the Vessel Setup information,
select OK and press Enter.
Engine Display Set-Up
On the Engine Display Setup screen, the C10
defaults Center in the Engine 1 box.
If you are only setting up the C10 for a single
engine, you do not need to make any
changes on this screen.
Select OK and press Enter.
Warning Screen
The C10 uses engine fuel ow to calculate the
remaining fuel in the fuel tank.
1. After completing the congurations above,
a Warning screen asks if any fuel has been
added to the vessel since the vessel was last
used.
If you select Yes, the Add Fuel screen will open.
2. It is recommended that you ll the fuel tank to
full capacity for the initial set-up of the fuel level
display in the C10.
NOTE:
If you desire, you can add a uid level sensor to the
vessel; then you can add a custom page to the C10
to monitor this information. These procedures are
outlined for you int he following pages.
8
Congure Devices on the Network
1. To congure devices on the vessel’s network,
press the Menu button once.
2. Press Enter to select Settings.
3. Use the arrow buttons to select System and
press Enter.
9
4. Select Network and press Enter.
5. Select Device List and press Enter.
6. The Device List screen that opens is used to
access and congure each device connected
to the network.
TIP:
You can use this screen to conrm that
your devices are properly connected to the
network. For example:
6.1 Select the device in question on the
list (in this example, Fluid Level),
then press Enter to go into Device
Conguration.
10
6.2 Select Data and press Enter.
6.3 Check for live data for that device.
If you see live data, this conrms that
the device is both connected properly
and is transmitting data to the C10.
Using the Auto Select Function
1. To add a device, press Menu once so that
the C10 returns to the System screen.
2. Select Network,then press Enter.
3. Select Auto Select, then press Enter.
Otros manuales para C10
1
Tabla de contenidos
Otros manuales de Monitor de Suzuki
