Sutron DRGS Manual de usuario
DRGS INSTALLATION GUIDE
1
DRGS INSTALLATION GUIDE
Prepared by:
The Sutron Corporation
21300 Ridgetop Circle
Sterling, VA 20166
2009
DRGS INSTALLATION GUIDE
2
TABLE OF CONTENTS
1. Introduction............................................................................................................................................. 3
2. Connecting Equipment........................................................................................................................ 4
3. Configure the DRGS PC ........................................................................................................................ 5
DRGS INSTALLATION GUIDE
3
1. INTRODUCTION
DRGS Receiver site has two components: VCS Receiver and DRGS PC. The DRGS PC
and receiver have already been configured and tested in Sutron before shipment. The
network cable need to be connected properly and the DRGS PC IP address need to be
changed to match the local network settings.
Please refer to the documents included on the VCS CD for more information.
DRGS INSTALLATION GUIDE
4
2. CONNECTING EQUIPMENT
1. Mount VCS Receiver and DRGS PC on the rack (if applicable).
2. Connect the power cord to both boxes
3. Connect satellite antenna cable to receiver
4. Connect the cross-over cable included from the receiver to DRGS PC named as
DRGS Private Connection. There are two network sockets on the back of DRGS PC.
Please find the one labeled “Private DRGS” in network properties.
5. Connect local network cable to the other network socket. This is the one labeled
“Local Network Connection” in network properties.
6. Connect a temporary keyboard, mouse and monitor to the DRGS PC. These can be
removed once the server has been configured. A remote access is enabled on the
DRGS PC.
7. Power on the VCS Receiver, then power on the Server PC.
DRGS INSTALLATION GUIDE
5
3. CONFIGURE THE DRGS PC
The DRGS PC has been configured, but the IP address needs to be changed to match
your local network settings in order to install on your local network. Get a static IP
address from the network administrator before starting.
1. Right click on “My Network Places” on desktop and select Properties.
2. Right click on “Local Area Connection” and select Properties.
DRGS INSTALLATION GUIDE
6
3. Select “Internet Protocol (TCP/IP)” and click Properties. If the PC has been
connected into a Local Network an IP address is assigned automatically. You can
change the IP address manually as supplied by the network administrator. A valid
gateway and DNS are required.
4. Click OK to close all network setting windows.
5. Configure the Time Server.
a. Install Nettime (http://nettime.sourceforge.net/)
b. Right click on NetTime tray icon on Windows task tray area. Click Settings and
change the NTP servers to your network time server.
c. Open Windows Service Manager. Disable Windows Time Service.
DRGS INSTALLATION GUIDE
7
6. Open VCS Monitor from “Start” | “All Programs”.
DRGS INSTALLATION GUIDE
8
7. Click Properties | General. DO NOT Change “Interface IP Address”, “Monitoring IP
Address” or Port Number leave them as configured. Make sure that “Receiver IP
Address” is the same as the IP address provided on the DSRII.
8. Change the channel settings by right click on channel and select Properties.
Change Channel (e.g. 157); Modulation (e.g. 100)
DRGS INSTALLATION GUIDE
9
9. Open XCDesktop from “Start” | “All Programs” | XConnect | XCDesktop. Select
Satellite Systems from the left tree view and then select XCMux. Change the IP
address to the server address.
10. Save all settings and close all programs. Reboot the server. This completes the
configuration.
Otros manuales de Antena de Sutron
Manuales populares de Antena de otras marcas
Alfa Network
Alfa Network APA-L01 Manual de usuario
Naval
Naval PR-422CA Manual de usuario
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario
TERK Technologies
TERK Technologies TV44 Manual de usuario
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK Manual de usuario
HP
HP J8999A Manual de usuario
