suprema CoreStation CS-40 Manual de usuario
2022/01/04 10:41 / How to configure CoreStation with an external wiegand device
- http://kb.supremainc.com/knowledge/
Table of Contents
How to configure CoreStation with an external wiegand device 1 .........................................................
Relay work video 7 .................................................................................................................................
2022/01/04 10:41 1/7 How to configure CoreStation with an external wiegand device
- http://kb.supremainc.com/knowledge/
How to configure CoreStation with an
external wiegand device
*If you would like to get basic information about configuration of CoreStation, please refer to How to
configure CoreStation
In this article, you will be able to learn how to connect an external Wiegand device to CoreStations.
And use it for certain operations such as authentication and entrance management with a door.
Materials used in this example:
1) HID Proximity Reader 5355
2) CoreStation
3) HID Prox Card 125kHz
1. When you take a look at the CoreStation(CS-40) manual, you can see a wiring diagram for the
product. CoreStation Manual
2. In this example, we will make use of “Wiegand 2” input as well as a power supply on this side
2022/01/04 10:41 2/7 How to configure CoreStation with an external wiegand device
- http://kb.supremainc.com/knowledge/
3. When you find the correct manual for the Wiegand reader product that you use, you can also find
its wiring diagram in it. Wire your Wiegand reader properly to CoreStation.
4. When you have wired it correctly you should have the wiring set up as below
- TTL Output ports 4&5 will be used for LED & Buzzer
5. Now let's go to BioStar 2, go to the Device menu, and click Search Device, add the CoreStation
device
6. Right-click on added CoreStation 40, and click “Add Wiegand Device”, in the new popup window
“Add Wiegand Device” add “Wiegand Reader 2.”
2022/01/04 10:41 3/7 How to configure CoreStation with an external wiegand device
- http://kb.supremainc.com/knowledge/
7. Click on added Wiegand Reader 2 and set the settings as you like. If you would like to control
LED/Buzzer, you can set it to a certain output.
- In this example, since Output 4 & Output 5 are close to Wiegand 2 Input, we will assign them to
these output ports.
8. Now go to the user tab, and select a user, in this example the default administrator is selected.
Let's click on the +Card button on a Credential section to assign a card to this user.
2022/01/04 10:41 4/7 How to configure CoreStation with an external wiegand device
- http://kb.supremainc.com/knowledge/
9. In the “Enroll Card” popup window, please set appropriate Wiegand settings according to the type
of card that you will use. The device will scan the card to obtain its card ID information automatically.
In our case 26-bit SIA Standard will be used as the card format.
1) Set Registration Option as “Register by Card Reader”
2) Set Device as “Wiegand Reader 2”
3) Click “Read Card” and scan the device with the card
3) Click Enroll.
*Do not forget to hit the “Apply” button on all main menus to take the changes into effect.
2022/01/04 10:41 5/7 How to configure CoreStation with an external wiegand device
- http://kb.supremainc.com/knowledge/
10. Go to the Monitoring menu and click on the Real-time log. When you scan cards on the Wiegand
reader, you will be able to see that the Wiegand reader sends card information to CoreStation for
authentication, and that authentication is successful with the card ID that we registered for the user.
You will also be able to hear the Buzzer sound and see LED lights turn to green when scanning the
card.
11. Now let's take this a little bit further. Go to the Door menu and click on the “Add Door” button. Set
its appropriate name (in this example we will call it “Suprema”).
1) Set the entry device as Wiegand Reader
2) Set Door Relay as Relay 2
3) Set Exit Button and Door Sensor to Supervised Inputs 4&5
4) Set the Open Time, this will dictate how much time you will have between locking and unlocking
when the relay goes ON and OFF
2022/01/04 10:41 6/7 How to configure CoreStation with an external wiegand device
- http://kb.supremainc.com/knowledge/
12. Go back to devices and click on CoreStation. Scroll down and expand the Advanced tab and turn
on Supervised Inputs 4&5 as we had set them up for Exit Button and Door Sensor. The resistance can
stay as 2.2K Ohms, as they are default. When you hit apply you can see that Supervised Inputs 4&5
will turn on their Green LEDs.
*For the reasons why 2.2k Ohms of circuit resistance for these Supervised Inputs are necessary,
please refer to article DM-20 Wiring Examples
13. Now go back to the Monitoring menu → Real-Time log. Scan the card on the Wiegand reader. You
will now see that not only authentication is successful but also the Door Relay will go ON and OFF,
indicating the door is being unlocked and locked. You can also notice this by seeing the red LED
turning ON and OFF on Relay 2, as well as the tipping sound that is coming from it. The time delay
between unlocking and locking will depend on Open Time that you set in step 11.
2022/01/04 10:41 7/7 How to configure CoreStation with an external wiegand device
- http://kb.supremainc.com/knowledge/
Relay work video
lxio6068.mp4
From:
http://kb.supremainc.com/knowledge/ -
Permanent link:
http://kb.supremainc.com/knowledge/doku.php?id=en:how_to_configure_corestation_with_an_external_wiegand_device
Last update: 2021/12/17 09:54
Tabla de contenidos
Otros manuales de Controladores de acceso IP de suprema
suprema
suprema FS2-D Manual de usuario
suprema
suprema bioentry w Manual de usuario
suprema
suprema BioLite N2 Manual de usuario
suprema
suprema Xpass Slim Manual de usuario
suprema
suprema Xpass Manual de usuario
suprema
suprema FaceStation Manual de usuario
suprema
suprema Xpass S2 Manual de usuario
suprema
suprema BioStation A2 Manual de usuario
suprema
suprema biostation Manual de usuario
suprema
suprema BioStation 3 Manual de usuario
