Supore LE-300 Manual de usuario
AUTO LENS EDGER
LE-300/LE-310/310P/320/400/420
Operation Manual
REV.20170608
1
PREFACE
INTRODUCTION OF PRODUCTS
According to the material of lens(GL,CR,PC),size of lens,
lens type(square lens samll size,right angle lens etc.),
lens edge(flat,beveling)etc,
Control by the electronic circuit to edging lens same as the mould.
Security information:
1、INTRODUCTION OF SECURITY SYMBOL
This signal means the aim of alert(involving notes),and special
alerts are marked in it.
The signal means forbidden operations(forbidden matters),
and special forbidden content is marked inside or near it.
The signal means operations that must be carried out, and
special explanations are marked in it.
2、ENVIRONMENT OF USE
（Avoid such harmful conditions below:）
A.temperature out of desired scope B.sharing wire board
C.violent shake D.sunlight
E. dust/fog F.moisture
2
3、ATTENTION
A. Don’t be suffered of violent struck
B. Don’t press the button violently.A light pressure is ok.
C. Don’t lean against the machine. The fallen of the machine
may cause injury.
D. Use dry cloth or wrenched wet clothing liquid to clean the
outside cover and keyboard.Cut off the power, and clean the fac of the
machine after daily work.
E.Don’t use any corrosive material or volatility liquid to clean
the machine.
3
LIST
INTRODUCTION OF PRODUCTS .....................................................................................1
Security information:..............................................................................................................1
1、INTRODUCTION OF SECURITY SYMBOL.......................................................1
2、ENVIRONMENT OF USE.......................................................................................1
3、ATTENTION.............................................................................................................2
Introduction.......................................................................................................................................4
1、LE-300/310/310P nomenclature..........................................................................................4
2、LE-320/400/420 nomenclature .........................................................................................5
3、LE-300/310/310PControl panel.......................................................................................6
4、LE-320/400/420 control panel ....................................................................................7
USE...................................................................................................................................................8
1、INSTALLATION...............................................................................................................8
A.installation of main machine ......................................................................................8
B. INSTALLION OF WATER TANK AND PIPE........................................................8
2、DEBUGGING..................................................................................................................10
3、OPERATION PROCEDURES ......................................................................................11
4.Wheel position emendation..................................................................................................18
Maintenance....................................................................................................................................24
Before requesting service................................................................................................................25
Specifications..................................................................................................................................26
Accessories and Tools.....................................................................................................................26
4
Introduction
1、LE-300/310/310P nomenclature
1
2
3
4
5
6
7
8
9
10
11
12
17
18
16
15
14
13
VENTILATING FAN
Plug for generalmains Fuse：20A
5
（1）soundproof cover 2）carriage weight-changing lever
（3）template retainer level （4）carriage backlashing sensor
（5）power cord （6）adjustable cover
（7）waterproof cover （8）carriage
（9）lens clamp （10）gear wheel
（11）operation panel （12）on/off switch
（13）water supply pipe （14）water supply cock
（15）pump power cord （16）pump
（17）drain pipe （18）tank
2、LE-320/400/420 nomenclature
6
⑴soundproof cover ⑵carriage weight-changing lever
⑶template retainer ⑷carriage backlashing sensor
⑸power cord ⑹adjustable cover
⑺waterproof cover ⑻carriage
⑼lens clamp ⑽gear wheel
⑾operation panel ⑿on/off switch
3、LE-300/310/310P Control panel
FUSE：20A
7
⑴Beveling and flat edge selctor ⑵test button
(3)Clamp pressure selector ⑷GL CR selector
⑸Metal and planel beating selector ⑹Ninus(-) button
⑺Plus (+) button ⑻Re-edging button
⑼Shift (left) button ⑽Shift(right) button
⑾Start button ⑿Stop button
⒀Lens-clamping button ⒁Lens-loosening button
4、LE-320/400/420 control panel
(1) PC、GL、Cr lens selector
(4) Polishing and impolishing selector
(5)Beveling and flat edge selctor
Others function same as LE-300/310/310P
8
USE
1、INSTALLATION
A.installation of main machine
a. Choose a fixed,horizontal and rigidity platform,ensuring its stability
and solidity
b. Put the machine on the platform as mentioned above
c. Open the outer casing and dismantle the screw,save the screw carefully.
d. Plug the power cord and turn on the switch
B. INSTALLION OF WATER TANK AND PIPE
9
a.Assemble the tank as illustrated.(see Fig 1)
b.Connect drain pipe as in Fig2
c.Show as Fig3 after installion.
please pay attention:
a.the filter basket should be cleaned regularly
b.water in tank should be changed frequently
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Arista de Supore
