Supermicro SuperServer SYS-121H-TNR Instrucciones de instalación
3
Abstract
This document provides clear guidance for end-of-life recyclers on how to identify
and disassemble reportable materials in compliance with the Waste Electrical and
Electronic Equipment (WEEE) directive.
WEEE DISASSEMBLY INSTRUCTIONS
SUPERMICRO SYS-121H-TNR ENCLOSURE
Table of Contents
1. Product Views............................................................................................................................................1
2. Reportable Materials on SYS-121H-TNR...................................................................................................2
3. Disassemble Instructions ..........................................................................................................................3
3.1 Recommended Disassembly Tools......................................................................................................3
3.2 Disassembled flowchart......................................................................................................................3
3.3 Step-by-Step Disassembly Instructions ..............................................................................................6
1. Removing Cable and Chassis Top Cover ...........................................................................................6
2. Removing Hard Disk Drive ................................................................................................................7
3. Removing Power Supply ...................................................................................................................8
4. Removing Backplane.........................................................................................................................9
5. Removing Fan ....................................................................................................................................9
6. Removing the Air shroud and Riser Bracket...................................................................................10
7. Removing the Riser Card.................................................................................................................10
8. Removing Processor........................................................................................................................10
9. Removing DIMM..............................................................................................................................12
10. Removing M.2..............................................................................................................................13
11. Removing Motherboard..............................................................................................................13
1
1. Product Views
Front view
Rear view
Product construct view
2
2. Reportable Materials on SYS-121H-TNR
According to Article 8(2) and Annex VII of WEEE directive 2012/19/EU, Below materials and components
should be selectively treated.
Description
Notes
No.
Quantity
Printed Circuit Boards (PCB) or
Printed Circuit Assemblies (PCA)
With a surface greater than 10 sq cm
(Depending on the product
configuration)
2.4, 3.5, 4.2, 4.1, 7.1,8.2,
9.1, 10.1, 11.1
28
Batteries
All types, including standard alkaline
and lithium coin or button style
batteries
11.2
1
Mercury-containing components
For example, mercury in lamps,
display backlights, scanner lamps,
switches, batteries
Liquid Crystal Displays (LCD) with
a surface greater than 100 sq cm
Includes background illuminated
displays with gas discharge lamps
Cathode Ray Tubes (CRT)
Capacitors / condensers
(Containing PCB/PCT)
Electrolytic Capacitors /
Condensers measuring greater
than 2.5 cm in diameter or height
Depending on the power supply
model
3.6
2
External electrical cables and
cords
1.1
2
Gas Discharge Lamps
Plastics containing Brominated
Flame Retardants weighing > 25
grams (not including PCBs or PCAs
already listed as a separate item
above)
Components and parts containing
toner and ink, including liquids,
semi-liquids (gel/paste), and toner
Include the cartridges, print heads,
tubes, vent chambers, and service
stations.
Components and waste containing
asbestos
Components, parts, and materials
containing refractory ceramic
fibers
Components, parts, and materials
containing radioactive substances
3. Disassemble Instructions
The intent of this document is to provide guidance to recyclers on the presence of materials and
components at the product / family level, as required by the EU WEEE Directive 2012/10/EU. This
document should also help direct recyclers to proper methods for removing parts and general
product disassembly instructions.
This chapter consists of three subsections:
Recommended disassembly tools, disassembled flowchart, and step-by-step disassembly
instructions to direct recycler proper methods to treat.
3.1 Recommended Disassembly Tools
Disassembly tool
Cross screwdriver
Flathead screwdriver
3.2 Disassembled flowchart
Server
Chassis
Power Supply
Storage Card and CPU
Chassis
Chassis Enclosure
Screw
Air Shroud
Motherboard/ Backplane/
Riser Card
Cable
Battery
Fan
Power Supply
Power Enclosure
Screw and Standoff
Power Supply Module
Power Cable
Storage Card and CPU
Heat Sink
Processor
Solid State Drive
TPM Module
DIMM
6
3.3 Step-by-Step Disassembly Instructions
1. Removing Cable and Chassis Top Cover
1. Use the operating system to power down the system.
2. After the system has completely shut down, disconnect the power cords from the power supply
modules.
.
4. Remove all cables/ unit from the server IO port.
5. Remove the top cover
No.
Description
No.
Description
1.1
Power Cable
1.6
1G LAN Ports
1.2
COM Port
1.7
VGA Port
1.3
Dedicated BMC LAN Port
1.8
Chassis
1.4
USB 2.0 Port
1.9
Top Cover
1.5
USB 3.2 Gen 1 Ports
1.8
1.9
1.1
1.2
1.3
1.4
1.5
1.6
1.7
7
2. Removing Hard Disk Drive
1. Push the release button on the drive carrier, which will extend the drive bay handle
2. Use the drive bay handle to pull the drive carrier out of the chassis
3. Release clasps and post, then pull out the dummy tray
5. Use a cross screwdriver to remove the drive enclosure
6. Use a cross screwdriver to remove the screws and lift off the PCB
2.1
2.4
2.2
2.3
8
No.
Description
2.1
Dummy Tray
2.2
Hard Drive
2.3
Hard Drive Enclosure
2.4
Hard Drive PCB
3. Removing Power Supply
1. Press the release tab on the failed power supply.
2. Use the handle to gently slide the power supply out the back of the chassis.
3. Remove the screw from the enclosure
4. Cut the power leads connected to the fan and lift the main board from the chassis
No.
Description
3.1
Power Supply
3.2
Power Enclosure
3.3
Fan
3.2
3.6
3.5
3.3
3.4
Otros manuales para SuperServer SYS-121H-TNR
1
Tabla de contenidos
Otros manuales de Servidor de Supermicro
Supermicro
Supermicro SuperWorkstation 540A-TR Manual de usuario
Supermicro
Supermicro SUPERSERVER 6013A-T Manual de usuario
Supermicro
Supermicro AS-2114S-WN24RT Manual de usuario
Supermicro
Supermicro SuperServer SYS-E200-12D-10C Manual de usuario
Supermicro
Supermicro SUPERSERVER 4029GP-TVRT Manual de usuario
Supermicro
Supermicro SUPERSERVER 6022P-i Manual de usuario
Supermicro
Supermicro A+ AS-1113S-WN10RT Manual de usuario
Supermicro
Supermicro SYS-F629P3-RTB Manual del propietario
Supermicro
Supermicro SuperServer SYS-210SE-31D Manual de usuario
Supermicro
Supermicro SuperServer SYS-121C-TN10R Manual de usuario
Supermicro
Supermicro SuperServer 5029AP-TN2 Manual de usuario
Supermicro
Supermicro SuperServer SYS-520P-WTR Manual de usuario
Supermicro
Supermicro SuperServer 6026TT-HTRF Manual de usuario
Supermicro
Supermicro SuperServer 1029P-WTR Manual de usuario
Supermicro
Supermicro SuperServer 8048B-TRFT Manual de usuario
Supermicro
Supermicro SuperServer E300-9D-4CN8TP Manual de usuario
Supermicro
Supermicro AS -1024US-TNR Manual de usuario
Supermicro
Supermicro A+ Server AS -2014S-TR Manual de usuario
Supermicro
Supermicro SuperServer SYS-511R-W Manual de usuario
Supermicro
Supermicro SuperServer SYS-E403-12P-FN2T Manual de usuario
