Superb NOMADA 12V105Ah Manual de usuario
Manual
NOMADA 12V105Ah
Version
April 2020
2
User Manual Nomada 12V105Ah
Dear customer,
This manual contains all the necessary information to install, use and maintain the Nomada
12V105Ah Li-ion battery. We kindly ask you to read this manual carefully before using the
product. In this manual, the Nomada 12V105Ah Li-ion battery will be referred to as: the Li-ion
battery. This manual is meant for the installer and the user of the Li-ion battery. Only qualied,
certied personnel may install and perform maintenance on the Li-ion battery. Please consult
the index at the start of this manual to locate information relevant to you.
During the use of the product, user safety should always be ensured, so installers, users,
service personnel and third parties can safely use the Li-ion battery.
Copyright© Super B All rights reserved. Licensed software products are owned by Super B
or its subsidiaries or suppliers, and are protected by national copyright laws and international
treaty provisions. Super B products are covered by Dutch and foreign patents, issued and
pending. Information in this publication supersedes that in all previously published material.
Specications and price change privileges reserved. Super B is a registered trademark of
Super B.
For more information please contact:
Super B Lithium Power B.V.
Demmersweg 3
7556 BN Hengelo (Ov) The Netherlands
Tel: +31(0)88 00 76 000
E-mail: info@super-b.com
www: www.super-b.com
3
Be in charge. Super B.
Table of content
1. Safety guidelines and measures 5
1.1. General 5
1.2. Disposal 5
2. Introduction 6
2.1. Product description 6
2.2. Intended use 6
2.3. Glossary of Terminology 6
2.4. Used symbols 7
3. Product specifications 7
3.1. Product features 7
3.2. Technical specications 7
3.2.1. Electrical specications 7
3.2.2. Mechanical specications 8
3.2.3. Charge & discharge specications 8
3.2.4. Temperature specications 8
3.2.5. Compliance specications 8
3.2.6. General product specications 9
3.3. Environmental conditions 9
3.4. Scope of delivery 9
3.5. Connections 10
3.5.1. Con 1 & 2 (CANopen; 5-pin “micro” style connector) 10
3.5.2. LED Indicators 11
3.6. Peripheral equipment 11
3.6.1. Obligatory 11
3.6.2. Optional Components 12
4. Installation 13
4.1. General information 13
4.2. Unpacking 13
4.3. Preparing the battery for use 13
4.4. Connection wires 13
4.4.1. Using the SB BIB (Battery Interface Box) 14
4.4.2. Using the SB BCI-C1 (Battery Communication Interface) with a normal relay 14
4.5. Disconnecting the Li-ion battery 15
5. Connecting Li-ion batteries in series and parallel 15
5.1. Connecting Li-ion batteries in series. 15
5.2. Connecting Li-ion batteries in parallel 15
5.3. Connecting Li-ion batteries in series and parallel 16
5.4. CANopen interface 17
4
5.4.1. CAN Bus network topology 17
5.4.2. Termination Resistors 18
5.4.3. CAN bus power 18
6. Battery use 19
6.1. General information 19
6.2. Charging 19
6.2.1. Battery balancing 20
6.2.2. Reading the battery’s State of Charge (SoC) 20
6.3. Battery Monitoring Software 20
6.3.1. Battery History Recording 20
7. Inspection and cleaning 20
7.1. General information 20
7.2. Inspection 21
7.3. Cleaning 21
8. Storage 21
9. Transportation 21
10. Disposal and recycling 22
11. Troubleshooting 22
12. Warranty and liability 23
5
Be in charge. Super B.
1. Safety guidelines and measures
1.1. General
• Do not short-circuit the Li-ion battery.
• Treat the Li-ion battery as described in this manual.
• Do not dismantle, crush, puncture, open or shred the Li-ion battery.
• Do not expose Li-ion battery to heat or re. Avoid exposure to direct sunlight.
• Do not remove the Li-ion battery from its original packaging until required for use.
• In the event of electrolyte leaking, do not allow the liquid to come in contact with the skin or
eyes. If contact has been made, wash the affected area with water and seek medical advice.
• Always use a class 2 charger which is specically provided for use with a Lithium Iron
Phosphate battery (LiFePO4)
• Observe the plus (+) and minus (–) marks on the Li-ion battery and equipment and ensure
correct use.
• Do not mix batteries of different manufacture, capacity, size or type.
• Keep the Li-ion battery clean.
• Secondary batteries need to be charged before use. Always use the correct charger and
refer this manual for proper charging instructions.
• Do not leave the Li-ion battery on prolonged charge when not in use.
• After extended periods of storage, it may be necessary to charge and discharge the Li-ion
battery several times to obtain maximum performance.
• Retain the original product documentation for future reference.
• Disconnect the Li-ion battery from the equipment when not in use.
• Do not charge the Li-ion battery below 0°C.
!
Warning! Keep the Li-ion battery away from dust and contamination. Place the Li-ion battery
in well ventilated areas.
1.2. Disposal
Dispose the Li-ion battery in accordance with local, state and federal laws
and regulations.
Batteries may be returned to the manufacturer.
Do not mix with other (industrial) waste.
Li-ion
WARNING:
Must be disposed of properly.
May explode if damaged or disposed
of in re. Do not short circuit.
6
2. Introduction
2.1. Product description
The Nomada 12V105Ah is a modular Lithium Iron Phosphate rechargeable battery. The Li-ion
battery has a compact and lightweight modular design which means you can easily scale
up your energy system. The unique combination of state-of-the art technology and smart
software makes this Li-ion battery a robust, safe and easy to use energy storage solution.
The Li-ion battery uses safe Lithium Iron phosphate (LiFePO4) technology. With its integrated
battery management system the Li-ion battery is protected from deep discharging,
overcharging and overheating.
!
Warning! It is required to use a Super B Battery Communication Interface (BCI) in
combination with an external disconnect device or a Super B Battery Interface Box (BIB), for
safe operation of the Nomada 12V105Ah Li-ion battery
2.2. Intended use
The Nomada 12V105Ah Li-ion battery serves as an energy source of 12V in power systems
for recreational vehicles, commercial vehicles, leisure boats, commercial vessels and
stationary applications. Potential applications for this Li-ion battery include: off grid power
supply, marine power supply, medium for (renewable) energy storage and (traction) battery
for vehicles. Using it as a starter battery is not possible. Up to 4 batteries can be connected
in series or in parallel to increase the total capacity up to 420Ah. When using more than 4
batteries in series or parallel always consult Super B.
2.3. Glossary of Terminology
BMS Battery Management System
Charge cycle A period of use from fully charged, to fully discharged, and fully recharged
again.
Endurance Life-cycle The products maximum lifespan, achieved by following the guidelines
presented in this manual.
BCI Battery Communication Interface
BIB Battery Interface Box
LiFeP04 Lithium Iron Phosphate
SoC State of charge
CCCV Constant Current - Constant Voltage
DoD Depth of Discharge
Table 1. Glossary of Terminology
7
Be in charge. Super B.
2.4. Used symbols
The following icons will be used throughout the manual:
!
Warning! A warning sign indicates severe damage to the user and/or product may occur
when a procedure is not carried out as described.
!
Caution! A caution sign indicates that problems may occur if a procedure is not carried out
as described. It may also serve as a reminder to the user.
3. Product specications
3.1. Product features
• Modular traction battery
• Lithium Iron Phosphate (LiFePO4): Safe Li-ion technology
• Integrated BMS (Battery Management System),
• BIB or BCI with disconnect device (relay) is required
• PC+ABS (UL94 V-0) ame-retardant battery casing
• Terminals for 2 x M8 bolts
• Maximum continuous discharge current: 315A
• External fuse needed
• Wired communication interface: CANopen
• Easy CAN bus interconnection
• Battery monitoring and history storage
• Adaptive cell balancing
• Congurable in serial or parallel connection
3.2. Technical specications
3.2.1. Electrical specications
Nominal capacity 105Ah
Energy 1344Wh
Nominal voltage 12.8V
Open circuit voltage 13.2V
Self discharge <3% per month
Table 2. Electrical specications
8
3.2.2. Mechanical specications
Dimensions (LxWxH) 437 x 90 x 175 mm / 17.2” x 3.5” x 6.9”
Weight 10 kg / 22 lbs
Case material PC+ABS (UL94 V-0) ame-retardant battery casing
Ingress protection IP66
Cell type / chemistry Prismatic - LiFePO4
Table 3. Mechanical specications
3.2.3. Charge & discharge specications
Charge method CCCV
Charge voltage 14.3V - 14.6V
Max charge current 105A
End of discharge voltage 10V
Max discharge current continous 315A
Max discharge pulse current
(10 sec, SoC >60%) 525A
Table 4. Charge and discharge specications
3.2.4. Temperature specications
Charge temperature 0°C to 55°C / 32°F to 131°F1
Discharge temperature -20°C to 55°C / -4°F to 131°F
Storage temperature short term (<1 month) -20°C to 45°C / -4°F to 113°F
Storage temperature long term (>1 month) 0°C to 35°C / 32°F to 95°F
Relative humidity 10-90%
Table 5. Temperature specications
1Do not charge the Li-ion battery below 0°C / 32°F
3.2.5. Compliance specications
Certications CE, FCC, UN 38.3
Shipping classication UN 3480
Table 6. Compliance specications
9
Be in charge. Super B.
3.2.6. General product specications
Battery designation IFpP/36/130/195/[1P4S]M/-20+55/95
Cycle life >3500 (1C charge/discharge, DoD 100%)2
Table 7. General product specications
2The cycle life value given above is an indication at 23°C. The Li-ion battery cycle life depends strongly on temperature
and the applied charging and discharging loads.
3.3. Environmental conditions
!
Warning! The Li-ion battery may only be used in conditions specied in this manual. Exposing
the Li-ion battery to conditions outside the specied boundaries may lead to serious damage
to the product and/or the user.
Use the Li-ion battery in a dry, clean, dust free, well ventilated area. Do not expose the
Li-ion battery to re, solvents or excessive heat.
3.4. Scope of delivery
132 4 5
Figure 1. Scope of delivery.
1. (1x) Nomada 12V105Ah lithium battery
2. (4x) M8 Bolt
3. (4x) M8 Spring washer
4. (4x) M8 Plain washer
5. (2x) Terminal protection cap
10
3.5. Connections
123 4
Figure 2. Connections
1. Con 1 (CANopen; 5-pin “micro” style connector female)
2. Con 2 (CANopen; 5-pin “micro” style connector male)
3. Terminal + (2x M8)
4. Terminal - (2x M8)
3.5.1. Con 1 & 2 (CANopen; 5-pin “micro” style connector)
PIN # Signal Description
1 CAN_SHLD Optional CAN Shield
2 CAN_V+
Optional CAN external positive supply
(dedicated for supply of transceiver and
optocouplers. if galvanic isolation of the bus
node applies)
3 CAN_GND Ground / 0V
4 CAN_H CAN_H bus line (dominant high)
5 CAN_L CAN_L bus line ( dominant low)
Table 8. Con 1 & 2 (CANopen; 5-pin “micro” style connector)
Tabla de contenidos
Otros manuales de Accesorios para cámaras de Superb
Superb
Superb SB12V100E-ZC Manual de usuario
Superb
Superb EPSILON 12V100Ah Manual de usuario
Superb
Superb Epsilon SB12V1200Wh-M Manual de usuario
Superb
Superb EPSILON 12V90Ah Manual de usuario
Superb
Superb MASON 12V20Ah Manual de usuario
Superb
Superb SB12V160E-ZC Manual de usuario
Superb
Superb SB12V2600P-AC Manual de usuario
Superb
Superb NOMIA 12V100Ah Manual de usuario
Superb
Superb NOMIA 12V340Ah Manual de usuario
Superb
Superb NOMIA 12V210AH Manual de usuario
