Supera EVC3100 Manual de usuario
Waste Gas Evacuation System
Model EVC3100
Supera, LLC Copyright 2023
For Veterinary Use Only
Examination and Preparation for Use
Thank you for ordering an Supera Anesthesia Innovations Product!
We are delighted to have you as a Supera Anesthesia Innovations
customer and want you to be completely satised with your purchase.
Please inspect the contents of your order to see if everything is as you
expected. Should anything not be exactly right or if anything was damaged
in shipping, please contact your sales representative right away for help.
Our goal is to make your new equipment as easy to use and care for as
possible.
This device is meant to be operated under the normal surveillance and
control of a veterinarian trained in its use. However, you need to know more
about this device than just how to operate it.
Please read this manual in its entirety before using the equipment.
If you have any comments or questions, we welcome the opportunity to
address them.
Please contact us directly at 877-620-1500.
Thank you!
Proudly 100% American
Made In Oregon!
MADE IN
oREGON, uSA
since 1993
IMPORTANT INFORMATION
READ AND SAVE THESE INSTRUCTIONS
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
Use this unit only in the manner intended by the manufacturer. If you have questions,
contact the manufacturer.
CAUTION
For General Ventilating Use Only. Do Not Use To Exhaust Hazardous Or Explosive
Materials And Vapors
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
a) Installation work and electrical wiring must be done by qualied person(s) in accordance
with all applicable codes and standards, including re-rated construction.
b) Ducted fans must always be vented to the outdoors.
THERE ARE NO USER SERVICEABLE PARTS INSIDE
Contact Supera LLC directly for all maintenance
and repairs. Technical service phone 877-620-1500
Symbol Chart
This document uses the following symbols to indicate potential hazards or alert the
user to useful information about the unit.
Important Notice – Explanation needed: refer to this manual
High Voltage: Risk of Electrical Shock
Protective Earth Ground
SUGGESTED MOUNTING INFORMATION
The area around the unit must be free of loose dirt and
debris
The area should be well ventilated with a maximum
temperature of 120 deg. F
This is a mechanical pump that emits noise (less than
70dB(A)) at a constant rate.
We recommend the unit be mounted in an area not in
constant use by people or animals.
INSTALLATION INSTRUCTIONS
1. Remove the panel to reveal the terminal block.
2. Attach the ground.
3. Attach the “L1” and “N” wires to the terminal block.
“L1”
Earth Ground
“N”
A EXHAUST - ¼ NPT FEMALE
B INLET TO BUILDING PLUMBING - ¼ NPT FEMALE
C ON/OFF SWITCH WITH CIRCUIT BREAKER
D NOTE: POWER CORD NOT INCLUDED
A
B
C
D
Hold Down Brackets
Screw down unit to a solid structure
(3 screws per side)
RECOMMENDED GUIDELINES
LOCATION
This is a mechanical pump that emits noise at a constant rate.
We recommend the unit be mounted in an area not in constant use by
people or animals.
POWER SWITCH
We recommend controlling the unit through a lighted power switch to
indicate the device is powered ON.
INTAKE
1/4 NPT fitting to ½” copper pipe.
EXHAUST
1/4 NPT fitting to 3/4” copper or 1” scd40 PVC pipe plumbed to outside
the building.
OUTLETS
Any piped gas outlets (WAGD) can be used. No ceiling or wall valves
are needed to control the flow rate, however, all active (suction style)
evacuation systems require waste gas interface (WGI) balance valves on
the anesthesia machines.
WASTE GAS INTERFACE
The EVC629 WGI with built in flow valve is
engineered for this system and requires no additional
calibration or maintenance.
It is mounted on the anesthesia machine and
attached to the pop o valve or non-rebreathing
system via the blue 19mm hose.
It is preset at 10 lpm flow. It can be adjusted higher
using a calibrated flow meter.
NOTE:
This should be done by a professional service
company.
GENERAL INFORMATION
Active Evacuation System
AES – anesthetic evacuation system utilizes a sealed evacuation unit
to remove waste gas to the outside air. The AES wall or ceiling outlets
are plumbed using copper pipe and are connected to the anesthesia
machine through the waste gas interface (WGI) device to balance the
negative pressure.
1-25 Anesthesia Machines
Uses standard wall/ceiling outlets
Plumbed using copper pipe
Uses waste gas interface EVC629 to balance evacuation pressure on
each anesthesia machine.
MAINTENACE
This AES unit is maintenance free.
TROUBLE SHOOTING
1. The no air is owing.
Check the on/o switch. If the switch is half way on/o, the circuit
breaker has been triggered. Reset the switch into the “ON” position.
2. The pump is on but not owing air at the outlets.
Check the exhaust pipe for obstructions (animals, debris, etc.)
Check the intake pipes for loose joints
FOR ALL OTHER ISSUES CALL SUPERA LLC AT 1-877-620-1500
Tabla de contenidos
Manuales populares de Bomba de agua de otras marcas
Sykes AmeriPumps
Sykes AmeriPumps GP100M Guía de solución de problemas
DUROMAX
DUROMAX XP WX Series Manual de usuario
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Manual de usuario
Franklin Electric
Franklin Electric IPS Manual de usuario
Xylem
Xylem e-1532 Series Manual de usuario
Milton Roy
Milton Roy PRIMEROYAL Manual de usuario