Sunsystem Burnit Manual de usuario
USER MANUAL
V 0.1
Mounting of pellet burner
on WBS or WBS Active boiler
Pell
Lower door
Plate 2
Plate 1
2
Mounting of Pell pellet burner on WBS or WBS Active boiler
Contents of BURNiT Pell 25 pellet burner mounting kit:
Package 1: nut М8 - 3 pcs. Mounting plate, gasket and
Carefully unpack elements inside the mounting kit package.
Check for visible defects or transport damages.
Boiler must be cooled down and disconnected from electric power!WBS or WBS Active
Step 1:
Step 3:
Fix the gasket and bolt the mounting plate
to the front side of the lower boiler door
using the same set of nuts.
Attach the burner to the lower boiler door
using the nuts from the fixation set of
the burner kit.
Step 4:
Step 2:
Front plate (Plate 1) is fixed with four nuts,
and plate 2 with two.
Remove the plates on both sides of the boiler
lower door.
The pellet burner shall be mounted onto
the resultant opening.
Gasket
Mounting plate
Lower door
Lower door
Burner
Lower door opening
(burner attaching place)
3
Mounting of Pell pellet burner on WBS or WBS Active boiler
Step 4:
Step 2:
Front plate (Plate 1) is fixed with four nuts,
and plate 2 with two.
Remove the plates on both sides of the boiler
lower door.
The pellet burner shall be mounted onto
the resultant opening.
Contents of BURNiT Pell 40/70 pellet burner mounting kit:
Package 1: nut М8 - 4 pcs. Mounting plate, gasket and
Attach the burner to the lower boiler door
using the nuts from the fixation set of
the burner kit.
Carefully unpack elements inside the mounting kit package.
Check for visible defects or transport damages.
Boiler WBS or WBS Active must be cooled down and disconnected from electric power!
Step 1:
Plate 2
Plate 1
Lower door
Gasket
Mounting plate
Lower door
Lower door
Burner
Lower door opening
(burner attaching place)
Step 3:
Fix the gasket and bolt the mounting plate
to the front side of the lower boiler door
using the same set of nuts.
Mounting of Pell pellet burner on WBS or WBS Active boiler
WARNING! Installation and setup of pellet burner should be done by an authorized specialist /
service shop and must follow the safety instructions and rules of operation. With view to
equipment safety, please assure that it is plugged out of the mains network upon mounting,
all elements are connected in due sequence and all joints (bolts and nuts) are properly secured.
Mounting temperature sensor.
(see diagram).
burner Burner temperature sensor controls and adjust
boiler temperature. Set boiler temperature by burner controller.
Dismantle top panel of WBS boiler/ front panel of WBS Active boiler.
Temperature sensor sleeve is located on upper part of boiler body
Step 5:
WBS boiler WBS Active boiler
Temperature sensor sleeve Temperature sensor sleeve
12 Madara Blvd, 9700 Shumen, Bulgaria
tel.: + 359 54 874 546
fax: + 359 54 874 556
NES Ltd.
new energy systems
Otros manuales de Quemador de Sunsystem
Sunsystem
Sunsystem Burnit Pell Series Manual del propietario
Sunsystem
Sunsystem BURNiT Pell BIO Series Manual del propietario
Sunsystem
Sunsystem BURNiT FH 500-V.2 Manual de usuario
Sunsystem
Sunsystem Burnit Pell Series Manual de usuario
Sunsystem
Sunsystem WBS-A 20 Manual de usuario
Sunsystem
Sunsystem BURNiT Pell Mega Series Manual del propietario
Sunsystem
Sunsystem Burnit Pell ECO Series Manual de usuario
