Sunshine HORIZON 4600 Instrucciones de instalación
Ver.2.0
CE845
Made In China For
ARLEC BARBEQUES PTY LTD
274 Maroondah Hwy
Mooroolbark, VIC 3138
Australia
!" #$
%!&$$'! (!&
!!! !)%!'
Retain These Instructions For Future Use
2
SAFETY PRECAUTION
•This grill is designed for outdoor use only THIS APPLIANCE SHALL
NOT BE INSTALLED OR USED INDOORS.
•The area surrounding your new grill should be kept clean, and free
from flammable liquids and other combustible materials such as
mops, rags, brooms, as well as solvents, cleaning fluids, and gasoline.
•Never locate this appliance in an enclosed room or under sealed
overhead structure or any type of enclosed area such as a garage,
shed, or breezeway. Keep clear of trees and shrubs.
•Never let clothing, potholders or other flammable materials come in
contact with or close to any grate, burner or hot surface until it has
cooled. Fabric may ignite and result in personal injury. Certain
materials or items, when stored under or near the appliance, will be
subjected to radiant heat and could be seriously damaged.
•BURNERS: Check to ensure no insects or blocking the venture tubes.
Use a special venture brush to clean. Use a pin or a toothpick to clean
the orifice on the gas valve. DO NOT ENLARGE THE HOLE.
SAFETY INSTRUCTION
•FOR OUTDOOR USE ONLY.
•READ THE INSTRUCTIONS BEFORE USING THE APPLIANCE.
•WARNING! : ACCESSIBLE PARTS MAY BE VERY HOT. KEEP
YOUNG CHILDREN AWAY. This appliance gets very hot. Take
special care when children or elderly people are present. Particular
care must be taken when removing the drip tray. Hot fat causes
severe injuries.
•DO NOT MOVE THE APPLIANCE DURING USE.
•TURN OFF THE GAS SUPPLY AT THE GAS CYLINDER AFTER
USE. Turn off all burner controls valves after use.
•ANY MODIFICATION TO THE APPLIANCE MAY BE DANGEROUS.
3
•THIS APPLIANCE SHALL BE KEPT AWAY FROM FLAMMABLE
MATERIALS. There should be no combustible materials less than
600 mm from the sides of barbecue and less than 1500 mm above the
cooking surface of the barbecue.
•Protective gloves should be worn if hot parts or utensils are to be
handled.
•People with flammable clothing such as nylon should keep well away
from the barbecue when alight.
•DO NOT allow unburned gas to build up.
•In the event of gas leak, TURN OFF GAS SUPPLY AT THE
CYLINDER.
•In the event of fat fire, DO NOT DOUSE WITH WATER. Turn off gas
supply at the cylinder.
•Every time the cylinder is reconnected, do a leak test.
•Never leave burners on high for more than 10 minutes unless cooking.
NATIONAL AUTHORITY REQUIREMENTS
All gas fitting work, service and repairs (including works on any part of
the gas circuit) can only be performed by an authorized gas fitter in
accordance with national regulations. All replacement parts must meet
Sunshine specification.
GAS TYPES
The barbecues are both category I3+(28-30/37) and I3B/P(30) appliances.
Gas consumption, inlet pressure and injector orifice sizes are shown in the
following tables.
HZ46 HZ47 Side Burner
Gas LPG LPG LPG
Inlet Pressure (mbar) 28 28 28
Heat Input (kW) 14 14 3
Injector Orifice (mm) 1.00 1.00 0.92
Gas Rate (g/h) 1020 1020 219
Note: The size of the injector orifice is stamped on one of the hexagon faces (eg:
“100” for 1.00 mm injector). LPG = Butane or Propane gas, propane is
recommended for use all year round. Butane for warmer climates/summer only.
4
ASSEMBLY INSTRUCTION
Inspect all components for damage before assembly begins. If damage is
present please contact your local dealer. Replace the damaged components
with original manufacturers’ parts only.
The cart panel, door, condiment assembly and main BBQ body have been pre
assembled for convenience and ease of assembly. Some assembly will be
required to complete this unit.
Assemble the barbecue trolley following steps as indicated below.
NB: some models have a round hole in the base for small gas bottles. In UK/Europe regulations
prohibit the use of gas bottles inside the BBQ cabinet, please locate bottle outside. The internal
hole can be used as a storage/rubbish bin and will fit standard bucket type bins.
Step 1
Assemble bottom shelf with trolley left hand
panel by sliding the front and rear legs of
panel onto the front and rear legs of bottom
shelf as illustrated.
Note : Make sure the black plastic inserts are
located on the left side facing down and the
door latches are facing the front. No screw
required for this step
Step 2
Install the trolley right hand panel on the
opposite side of the bottom shelf with the
same procedure.
Note : No screw required for this step
Step 3
Remove castor from the packaging and place
lockable castor on LH leg assembly and fixed
castor on RH leg assembly under the bottom
shelf. To secure lockable castor, make sure
the lockable castor is in lock position. Screw
castor into the black plastic inserts and hand
tight. Release brake when finished.
Note : No screw required for this step
5
Step 4
Attach the horizontal support rail to the front
legs. Then align the holes on both ends of the
support rail with the threaded holes on the
legs. Tighten with two M5 screws.
Step 5
Insert four M5 screws into the LH and RH
rear legs with hand tighten. Make sure to
loosen the screws to slide in the rear panel.
Step 6
Attach rear panel between RH and LH rear
leg. Align the slots on the rear panel on the
srews and push with a gentle downward
pressure as illustrated. Tighten all four
screws.
Step 7
Place door assembly in front of LH cart
assembly, ensure that the door handle are on
top position. Slide the bracket located at the
back of door assembly onto the LH stud on
the front of the trolley left hand panel as
illustrated.
6
Step 8
Place condiment shelf assembly in front of
the trolley right hand panel, ensure that the
condiment shelf handle are on top position.
Slide the bracket located at the back of
condiment shelf assembly onto the RH stud
on trolley right hand panel as illustrated.
Step 9
Place front trimming infront of RH and LH
trolley assembly. Align bolt holes located on
the inside RH/LH trolley assembly and secure
using four M5 long bolts.
Step 10
Attach LH side shelf assembly to LH trolley
assembly, slide LH side table assembly onto
front/rear legs of the L/H frame with
downward pressure as shown. Secure with
three bolts and nuts. Make sure the table is
slotted in equally during assembly.
NB: Different models come with different side shelf
units. These units may (or may not) include
side burner, marinating bowl, ice chest/sink or
lid.
7
Step 11
Attach RH side burner assembly to RH cart
assembly, slide RH side burner assembly
onto front/rear legs of the RH frame with
downward pressure as shown. Tighten with 2
bolts and nuts only to the outsides holes only.
Step 12
Attached cylinder hook under RH panel bar. Align the hole and secure with
bolt and nut.
Step 13
Remove bbq body assembly from the
packaging and take out grill plate, hot plate,
warming rack, flame tamer and all
accessories inside the bbq to reduce weight.
Lift the bbq body over the trolley assembly
and carefully lower onto the trolley until the
BBQ body rests on the upper side section of
side shelf.
8
Step 14
Place the grill plate flame tamers on right
lower level of bbq body assembly directly
above burners between the location tabs on
the bbq chassis.
Step 15
Insert the warming rack and place cast iron
grill plate directly above flame tamers and hot
plate on support ribs as illustrated.
Step 15
Slide the drip tray on bottom of barbecue
body as illustrated. Make sure the drip tray is
seated properly inside the location tabs. The
drip container fits under the drip tray run off
hole.
Assembly of the barbecue is complete.
Please read all cautions and warnings before
using your barbecue
9
LIGHT
Every HORIZON BBQ has been equipped with tested LED located inside the
hood handle. The LED provided, produces a unique light effect in forward
direction for convenience at night time. The battery compartment is located on
the left hand side of handle.
To install the batteries, unscrew counter clockwise the battery compartment
from handle as indicated in Figure below. The battery compartment houses
three size “C” batteries. Check for correct polarity alignment as indicated in the
battery compartment. Once batteries are installed, replace the battery
compartment. Turning it clockwise until it stops.
CAUTION! Do Not Over Tighten, and do not use battery compartment to lift
hood.
CAUTION!
•There are no user serviceable parts for this LED unit. Do not attempt any
repairs yourself, doing so will void the manufactures warranty. In the
unlikely event, your unit may require service. Please contact your nearest
Arlec Sunshine Barbecue dealer.
•Do not modify the circuit. This circuit is already optimized and confirmed
by tests and by measurements.
GAS SUPPLY CYLINDER
LP gas cylinders used with this appliance must have a cylinder capacity of at
LEAST 6 kg if propane or 13 kg if Butane.
GAS REGULATOR
A gas regulator conforming to the national standard must be fitted to the gas
cylinder to provide the appropriate gas pressure.
WARNING! : NEVER ATTEMPT TO OPEN OR ADJUST THE REGULATOR
Consult your gas dealer if you think the regulator is not working properly.
10
SUPPLY HOSE
A hose conforming to the national standard must be connected at one end to
the regulator outlet and at the other to the barbecue inlet nipple using hose
clips. The hose length must not exceed 1.5 m.
CONNECTING THE GAS SUPPLY
1. Screw the female flared fitting of the hose and regulator onto the bbq
inlet fitting at one side and side burner inlet fitting on the other side,
tighten using two adjustable wrenches. These fittings should be
tightened in a clockwise direction. Be sure that the connection is tight
(do not over tighten).
Ensure that all connecting threads and surfaces
are undamaged, clean and free from oil and dirt.
When fitting the hose, ensure that it is free from torsional (twisting)
stress, kinks or sharp bends. Protect the hose from dripping grease
and do not allow it to touch any hot surfaces, or sharp edge.
2. Attach the regulator to the gas cylinder. Refer to the instructions
supplied with the regulator for details regarding fitting.
3. Test for gas leak. Do a test leak each time the cylinder is installed,
whether it has been refilled or not. Check all other joints at least once
a year. If the hose shows deterioration or damage, leak test the entire
outer surface while under pressure. Replace at first sign of leak or age
cracking. Remember to turn the cylinder valve OFF before removing
hose.
CHECKING FOR LEAKS
Turn the gas on at the cylinder, or make sure gas is
available to the barbecue, but do not turn the burners on.
This fills the gas lines with gas. Now brush or pour some
soapy water onto all connections. If there Is a leak.
bubbles should appear within about 20 seconds. If you
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Parrilla de Sunshine
