sunjoe LJSS100 Manual de usuario
Form No. SJ-LJSS100-880E-M
If you have any questions or comments,
please call the Snow Joe®+ Sun Joe®customer service department at:
1-866-SNOWJOE (1-866-766-9563)
© 2022 by Snow Joe®, LLC
All rights reserved. Original instructions. SAVE THESE INSTRUCTIONS
LOG SPLITTER SUPPORT STAND
COMPATIBLE WITH LJ602E + 24V-X2-LS6T
Model LJSS100
R
EN
1
Know Your Log Splitter Support Stand
Read the owner’s manual and safety rules carefully before using your log splitter support stand.
Compare the illustration below to the actual unit in order to familiarize yourself with the location of the
various controls and adjustments. Save this manual for future reference.
1. Bolt
2. Log splitter axle
3. Rear post
Technical Data
Compatibility ............................................ LJ602E
24V-X2-LS6T
Weight Capacity .......................... 440 lbs (200 kg)
Dimensions................35.5"(L) x 28"(W) x 29.5"(H)
90 cm (L) x 71 cm (W) x 75 cm (H)
Net Weight......................................... 11 lbs (5 kg)
1
6
2
3
4
7
8
5
4. Screw knob
5. Support stand axle
6. Beam
7. Bracket
8. Front post
Wheels + log splitter not included
2
Unpacking
Carton Contents
• Support stand axle
• Rear posts (x2)
• Front post
• Beam
• Screw Knobs (x3)
• Bolts (x6)
• Lock nuts (x4)
• Washers (x4)
• Retaining rings (x2)
• Retaining ring pliers
• Manual and registration card
1. Carefully remove the support stand and
check to see that all of the above items are
supplied.
2. Inspect the product carefully to make
sure no breakage or damage occurred
duringshipping.Ifyounddamagedor
missing parts, DO NOT return the unit to
the store. Instead, please call the Snow
Joe®+ Sun Joe®customer service center at
1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton
and packaging material until you are
ready to use your new support stand. The
packaging is made of recyclable materials.
Properly dispose of these materials in
accordance with local regulations.
IMPORTANT! The equipment and
packaging material are not toys. Do not
let children play with plastic bags, foils, or
small parts. These items can be swallowed
andposeasuocationrisk!
mWARNING! To reduce the risk of
injury, the user must read and understand this
operator’s manual before using this product.
Failure to follow all warnings and precautions
may result in personal injury or property damage.
Disassemble Log Splitter
Wheels & Front Stand
Log splitter sold separately
Tools required: screwdriver + wrench set
1. To remove the hub cap from the wheels,
pushthesnapttingsoutfromthebackof
the wheel using a screwdriver (Fig. 1).
2. Remove the retaining ring from the end
of the log splitter axle using the provided
retaining ring pliers (Fig. 2).
3. Pullthewheelsothelogsplitter.
4. Detach the front stand of the log splitter by
removing the nuts underneath (Fig. 3).
Fig. 1 Hub cap
Wheel
Fig. 2
Retaining
ring pliers
Retaining ring
Fig. 3
Front
Stand
Nut
Log Splitter
3
Support Stand Assembly
NOTE: Due to the weight of the log splitter, we
highly recommend assembling the unit with the
help of at least one other person.
1. Fix the beam, front post and the two
brackets together using four sets of bolts,
washers and lock nuts (Fig. 4).
2. Slide the other end of the beam through the
support stand axle, then loosely thread the
screw knob into the nut (Fig. 5).
NOTE: Do not tighten down the screw
knob yet.
3. Slide the wheels onto the support stand
axle and secure them in place using the
retaining rings (Fig. 6).
Fig. 4
Bracket
Lock
nut
Washer Bolt
Fig. 5
Support
stand axle
Screw knob
Beam
Fig. 6 Support
stand axle
Wheel
Retaining
ring
Retaining
ring pliers
4. Snap the hub caps back onto the wheels.
5. Install both rear posts onto the log splitter
axle through the bottom holes (Fig. 7).
6. Insert the other end of both rear posts
through the vertical box sections on the
support stand axle. Tighten using the two
remaining screw knobs (Fig. 8).
7. Pivot the log splitter so that the front stand
mount rests on top of the front post. Fix
them together using the nuts and bolts
disassembled from the front stand (Fig. 9).
NOTE: The front post may need to shift
forwards or backwards in order to match
the bottom of the front stand mount. This is
why the middle screw knob should only be
threaded on loosely.
Fig. 7
Rear posts
Log splitter axle
Fig. 8 Rear
posts
Support stand axle
Screw
knob
Fig. 9
Front
post
Front stand
mount BoltBolt
Nut
4
8. Tighten the middle screw knob (Fig. 5).
9. Fix the rear posts to the log splitter using
the two remaining bolts (Fig. 10)
Service + Support
If your Sun Joe®LJSS100 Log Splitter Support
Stand requires service or maintenance, please
call Snow Joe®+ Sun Joe®customer service
at 1-866-SNOWJOE (1-866-766-9563) for
assistance.
Model + Serial Numbers
When contacting the company or arranging
service from an authorized dealer, you will need
to provide the model and serial numbers, which
can be found on the registration card. Copy
these numbers into the space provided below.
Fig. 10
Bolt Rear
posts
Record the following numbers from the registration card
of your new product:
Model #:
Serial #:
L
J S S
1 0 0
5
OUR WARRANTY:
Snow Joe warrants new, genuine, powered and non-powered Products to be free from defects in
material or workmanship when used for ordinary household use for a period of two years from the
date of purchase by the original, end-user purchaser when purchased from Snow Joe or from one of
Snow Joe’s authorized sellers with proof of purchase. Because Snow Joe is unable to control the quality of
its Products sold by unauthorized sellers, unless otherwise prohibited by law, this Warranty does not cover
Products purchased from unauthorized sellers. If your Product does not work or there’s an issue with a specic
part that is covered by the terms of this Warranty, Snow Joe will elect to either (1) send you a free replacement
part, (2) replace the Product with a new or comparable product at no charge, or (3) repair the Product. How
cool is that!
This Warranty gives you specific legal rights, and you may also have other rights which vary from State
to State.
PRODUCT REGISTRATION:
Snow Joe strongly encourages you to register your Product. You can register online at snowjoe.com/register,
or by printing and mailing in a registration card available online from our website, or calling our Customer
Service Department at 1-866-SNOWJOE (1-866-766-9563), or by e-mailing us at [email protected]. Failure
to register your Product will not diminish your warranty rights. However, registering your Product will allow
Snow Joe to better serve you with any of your customer service needs.
WHO CAN SEEK LIMITED WARRANTY COVERAGE:
This Warranty is extended by Snow Joe to the original purchaser and original owner of the Product.
WHAT IS NOT COVERED?
This Warranty does not apply if the Product has been used commercially or for non-household or rental
applications. This Warranty also does not apply if the Product was purchased from an unauthorized
seller. This Warranty also does not cover cosmetic changes that do not aect performance. Wearing
parts like belts, augers, chains and tines are not covered under this Warranty, and can be purchased at
snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563).
R4_01282020
SNOW JOE®+ SUN JOE®CUSTOMER PROMISE
ABOVE ALL ELSE, Snow Joe, LLC (“Snow Joe”) is dedicated to you, our customer. We strive to make your
experience as pleasant as possible. Unfortunately, there are times when a Snow Joe®, Sun Joe®, or Aqua Joe®
product (“Product”) does not work or breaks under normal operating conditions. We think it’s important that
you know what you can expect from us. That’s why we have a Limited Warranty (“Warranty”) for our Products.
EN
6
7
Forma № SJ-LJSS100-880S-M
Si tiene preguntas o comentarios,
comuníquese con la central de servicio al cliente Snow Joe® + Sun Joe® llamando al:
1-866-SNOWJOE (1-866-766-9563)
© 2022 Snow Joe®, LLC
Derechos reservados. Instrucciones originales. GUARDE ESTAS INSTRUCCIONES
BASE DE SOPORTE PARA
PARTIDOR DE TRONCOS
COMPATIBLE CON LJ602E + 24V-X2-LS6T
Modelo LJSS100
R
ES
9
Conozca su base de soporte para partidor de troncos
Lea detenidamente este manual del propietario y el reglamento de seguridad antes de usar su
base de soporte para partidor de troncos. Compare la ilustración debajo con la unidad real para
familiarizarse con las ubicaciones de los diversos controles y ajustes. Conserve este manual para
futuras referencias.
1. Perno
2. Eje de partidor
de troncos
Datos técnicos
Compatible con................................................ LJ602
24V-X2-LS6T
Capacidad de peso.............................440 lb (200 kg)
Dimensiones............................ 35.5 plg (90 cm) largo
28 plg (71 cm) ancho
29.5 plg (75 cm) alto
Peso neto ..................................................11 lb (5 kg)
1
6
2
3
4
7
8
5
3. Poste trasero
4. Perilla atornillable
5. Eje de base de
soporte
6. Barra
7. Sujetador
8. Poste frontal
No incluye ruedas y partidor de troncos
10
Tabla de contenidos
Idiomas:
Otros manuales de Partidor de troncos de sunjoe
Manuales populares de Partidor de troncos de otras marcas
Scheppach
Scheppach OX 3-1000 Instrucciones de montaje
Swisher
Swisher 21200 Manual de usuario
Elem Garden Technic
Elem Garden Technic FBHT65-22TCH Manual de usuario
Champion Power Equipment
Champion Power Equipment 90720 Manual
Boss Industrial
Boss Industrial ES5T20 Manual de usuario
Villager
Villager LSP 12 T Manual de usuario
