Sun Oracle Netra SPARC T3-1B Manual de usuario
1
This guide describes the minimum steps required to install and power on Oracle’s Netra SPARC T3-1B server
module for the first time.
For more detailed installation information, refer to the online Netra SPARC T3-1B Server Module Installation Guide
and the installation guide for your Sun Netra 6000 modular system. Also read the latest Netra SPARC T3-1B
Server Module Product Notes to find out if any late-breaking issues impact installation requirements:
http://www.oracle.com/pls/topic/lookup?ctx=E21652-01&id=homepage
Shipping Kit Contents
▼Install Optional Components
♦Before installing the server module into the modular system chassis, install any optional components that
you ordered for the server module.
Optional components might already be installed in the server module you received. See the customer
information sheet for details. For instructions on installing optional components, refer to the documentation
for each component and the Netra SPARC T3-1B Server Module Service Manual.
Figure Legend
1Printed documentation
2Server module
3Shipping carton
4Customer information sheet (save this for MAC
addresses and other information)
Netra SPARC T3-1B Server Module
Getting Started Guide
2
▼Install the Server Module Into the Chassis
The server module is hot-pluggable in the chassis. The instructions in this guide assume that the Sun Blade
6000 modular system is installed, and is up and running.
1. Remove the filler panel from the desired server module slot in the chassis.
Be ready to insert the server module or a filler panel in the empty slot within 60 seconds.
2. Insert the server module in the chassis (panel 1) until it is about 1.5 cm (.5 in.) from the front of the
chassis.
The side of the server module with the service label faces to your right.
3. Extend the ejector levers (panel 2), then push the ejector levers in simultaneously until they lock in place
(panel 3).
4. Verify the server module insertion by checking the green OK LED on the server module (panel 4).
When the server module is plugged in, standby power is supplied to the service processor (SP). The front
panel LEDs blink three times, then the green OK LED on the front panel blinks for a few minutes. The server
module SP generates diagnostic messages as soon as the server module is connected to a powered modular
system.
Caution – For proper cooling, ensure that all slots are filled with a server module or a filler panel. Fill
all slots within 60 seconds after the modular system is connected to power.
3
▼Determine Your Connection Method
You can start, boot, and manage the server module using the Oracle Integrated Lights Out Manager (ILOM)
software that runs on the server module SP. You can also control the server module from Oracle ILOM
running on the chassis management module (CMM) of the modular system.
There are several ways that you can connect to the server module SP.
♦Connect to the server module using one of the methods shown in the following figure and table.
This guide uses method 1, but you can use the other methods as described in the Netra SPARC T3-1B Server
Module Installation Guide.
Method Connection Description
1 Ethernet
From: CMM NET MGT port
To: Your network
(This guide includes details on this method)
Ensure that the CMM NET MGT port is connected to your network.
From your network, log into Oracle ILOM on the CMM using the IP address
of the CMM. Use the Oracle ILOM proxy to navigate to the server module SP
Oracle ILOM interface. You can use the Oracle ILOM command-line interface
(CLI) or use the CMM Oracle ILOM web interface (as described in “Access
Oracle ILOM on the Server Module SP (Web Interface)” ).
2 Serial
From: CMM SER MGT port
To: Terminal device
Connect a terminal device to the CMM SER MGT RJ-45 port and use Oracle
ILOM to navigate to the server module SP Oracle ILOM interface. This
method only supports the Oracle ILOM CLI.
3 Serial
From: Server module SP UCP port
(dongle required)
To: Terminal device
Connect a UCP-3 dongle cable to the server module. Connect a terminal
device to the RJ-45 connector on the dongle cable. Communicate with Oracle
ILOM on the server module SP using the Oracle ILOM CLI.
4
▼Access Oracle ILOM on the Server Module SP (Web Interface)
This procedure is for method 1, which uses a web interface through the CMM to access the server module Oracle
ILOM CLI. You must know the CMM IP address to perform this procedure. This procedure also assumes you
have a DHCP environment. For other environments, see instructions in the SPARC T3-1B Server Module
Installation Guide.
1. Ensure that the CMM NET MGT port is connected and configured to communicate on your network.
Refer to the Sun Blade 6000 modular system documentation for details.
2. In a browser on the same network as the modular system, enter the IP address of the CMM.
For example, if your CMM has the IP address 129.99.99.99, direct your browser to that address. A login
window for Oracle ILOM will appear.
3. Log in to Oracle ILOM on the CMM by typing your user name and password.
The factory default Oracle ILOM root password is changeme.
You are now logged in to the CMM Oracle ILOM web interface.
4. Navigate to the server module SP.
a. Select the chassis view for the modular system.
b. Click on the image of the server module that you have installed in the modular system.
The slots in the modular system are numbered from 0 to 9.
5. Start the Remote Console.
a. Select Remote Control on the top menu.
b. Select the Redirection tab.
c. Click on Use serial redirection.
d. Click on Launch Remote Console.
6. Power on the server module.
a. Select the Remote Power Control tab.
b. Click on the menu in that tab and select Power On.
c. Select Save.
d. Select OK when you see this prompt: Are you sure you want to perform a Power On of the server.
The server module host is powered on for the first time. The server module hardware installation is complete
and the server module is ready to be configured to suit your needs. For details on the Oracle Solaris OS
configuration process, see the Netra SPARC T3-1B Installation Guide and the installation guides for your
version of Oracle Solaris OS.
▼Power On the Server Module Host
If you used a command line method to access the server module SP, rather than use the procedure in “Access
Oracle ILOM on the Server Module SP (Web Interface)” , you need to use this procedure to power on the server
module host.
5
1. Power on the server module host.
The server module initializes.
2. Switch communication to the server module host.
The server module might take several minutes to complete POST. If a boot device installed with the Oracle
Solaris OS is accessible locally, the server module boots. Otherwise, the system uses the boot net command
to seek a boot device on the network.
You are now connected to the server module host.
The server module hardware installation is complete and the server module is ready to be configured to suit
your needs. For details on the Oracle Solaris OS configuration process, see the Netra SPARC T3-1B Server
Module Installation Guide and the installation guides for your version of Oracle Solaris OS.
▼Check for the Latest OS, Patches, and Firmware
Later versions of OS, patches, and firmware might be available for your server module. Some features can
only be enabled when certain patches or firmware are installed. Install the latest available versions for the
best performance, security, and stability.
1. Review the SPARC T3-1B Server Module Product Notes at:
http://www.oracle.com/pls/topic/lookup?ctx=E21652-01&id=homepage
This document describes important product dependencies and late-breaking information.
2. Access the latest OS, patches, and firmware information from the system administration portal:
http://www.oracle.com/technetwork/systems/software-stacks/stacks/index.html
Under the Netra Carrier-Grade Systems heading, select the Netra SPARC T3-1B Server Module link.
-> start /SYS
Are you sure you want to start /SYS (y/n)? y
Starting /SYS . . .
-> start /HOST/console
Are you sure you want to start /HOST/console (y/n)? y
Serial console started. To stop, type #.
6
Accessing Additional Information
Find the documentation for Oracle’s Netra SPARC T3-1B server module at:
http://www.oracle.com/pls/topic/lookup?ctx=E21652-01&id=homepage
Product Documentation
You can view, print, or purchase a broad selection of documentation, including localized versions, at:
http://www.oracle.com/technetwork/documentation/index.html
Technical Support
If you have technical questions about this product that are not answered in this document, go to:
https://support.oracle.com
Task Document Title or URL
Review known issues, workarounds, and
new information.
Netra SPARC T3-1B Server Module Product Notes
Connect to server module for initial
installation and configuration.
Netra SPARC T3-1B Server Module Installation Guide
Set remote access. View system status and
event logs.
SPARC T3 Series Servers Administration Guide
Diagnose and troubleshoot the server
module. Remove and replace components.
Netra SPARC T3-1B Server Module Service Manual
Review safety information. Netra SPARC T3-1B Server Module Safety and Compliance Manual
Important Safety Information for Sun Hardware Systems
Access chassis-specific hardware and Oracle
ILOM information.
http://www.oracle.com/technetwork/documentation/netra-
blade-servers-252766.html
Access preinstalled OS information. http://www.sun.com/software/preinstall
Copyright © 2011, Oracle and/or its affiliates. All rights reserved.
Copyright © 2011, Oracle et/ou ses affiliés. Tous droits réservés.
Part No.: E21658-01,
Mfg No.: 7012752,
April 2011
Otros manuales para Netra SPARC T3-1B
2
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Servidor de Sun Oracle
Sun Oracle
Sun Oracle SPARC T3-1 Manual de usuario
Sun Oracle
Sun Oracle Fire X4440 Manual de usuario
Sun Oracle
Sun Oracle Sun Server X4-2L Manual de usuario
Sun Oracle
Sun Oracle Blade X4-2B Manual de usuario
Sun Oracle
Sun Oracle Sun Fire X4800 Manual de usuario
Sun Oracle
Sun Oracle X4270 M2 Manual de usuario
Sun Oracle
Sun Oracle Sun Blade X3-2B Manual de usuario
Sun Oracle
Sun Oracle Fire X4470 Manual de usuario
Sun Oracle
Sun Oracle SPARC SuperCluster T4-4 Manual de instalación y funcionamiento
Sun Oracle
Sun Oracle 4540 - Phaser Copystation Manual de usuario
Sun Oracle
Sun Oracle Sun Blade 6048 Manual de servicio
Sun Oracle
Sun Oracle Netra X6270 Manual de usuario
Sun Oracle
Sun Oracle SPARC T4-1 Manual de usuario
Sun Oracle
Sun Oracle SPARC T3-1 Manual de usuario
Sun Oracle
Sun Oracle Netra SPARC T3-1B Manual de servicio
Sun Oracle
Sun Oracle Sun Server X4-2 Manual de usuario
Sun Oracle
Sun Oracle Sun Netra T5440 Manual de usuario
Sun Oracle
Sun Oracle Sun Blade X3-2B Manual de usuario
Sun Oracle
Sun Oracle T5120 Manual de usuario
Sun Oracle
Sun Oracle Fire X4470 Manual de usuario
