Sun Heat F-15 Gen IV Instrucciones de montaje
F-15 Gen IV Fireplace
Repair Guide
!!Unplug The Heater Before Servicing!!
(Remember That The Edges Of The Metal Are Sharp. Use Caution)
A. Remove Center From The Wood Mantle
B. Remove Center Top Cap
C. Remove Front Glass
D. Remove Fire Log Set & Firelight Screen
E. Replace Heat Tubes
F. Replace High Limit Switch (120c)
G. Replace Flame Effect On/Off Switch
H. Replace Flame Effect Fuse (1 amp)
This unit has a grey remote, 1 bottom fan for
the flame effect and 2 top circulation fans
I. Replace Master Reset Breaker (16 amp)
J. Replace Heat Exchanger Circulation Fans (12 volt)
K. Replace Tip Over Switch
L. Replace Power Routing Board
M. Replace Circuit Board
N. Replace Display Screen
O. Replace Air Temperature Sensor
P. Replace Flame Effect Light Bulb Socket
Q. Replace AC Case Fan
R. Replace Fire Light Drive Rod Motor
S. Replace Power Cord
T. Replace Center Mounting Anchors
U. Wiring Diagram
Questions: Please Call
Customer Service
1-877-467-8643
A
Remove Center From The Wood Mantle
!!Unplug The Heater Before Servicing!!
(Remember That The Edges Of The Metal Are Sharp. Use Caution)
Unscrew the 4 wing bolts that hold the fireplace center into the wooden mantle (See Wing
Bolt Locations Below). After the removal of the wing bolts, slide the fireplace center out the
front of the mantle. Note: Be careful to protect the lower lip of the mantle with a piece of
cardboard or sheet of heavy plastic. There are screw heads on the bottom of the metal center
that will damage the finish on the wood if not protected.
Wing Bolts
B
Remove Center Top Cap
!!Unplug The Heater Before Servicing!!
(Remember That The Edges Of The Metal Are Sharp. Use Caution)
With the center removed from the mantle, lower the front grill to gain access to the power
switch/fuse/reset button panel. This panel is located on the left side. Remove the 4 screws
that hold this panel in place.
After the removal of the 4 screws that hold this panel in place, tilt the panel at a slight angle
and place into the hole that the panel covers.
B
Remove the 11 perimeter screws that hold the center top cap in place.
Perimeter Screws
Perimeter Screws
Perimeter Screws
B
Lift the top cap upward from the front. NOTE: Be careful not to lift the top cap too far or
damage may occur to the wires that connect the display screen to the circuit board.
Disconnect the wire harness that runs from the display screen to the circuit board.
C
Remove Glass
!!Unplug The Heater Before Servicing!!
(Remember That The Edges Of The Metal Are Sharp. Use Caution)
You are able to remove the glass without having to completely dismantle the unit. Loosen the
4 wing bolts that hold the center unit into the wood cabinet and push the center forward
slightly.
You will remove 2 screws on each side of the grill hinge in order to remove the grill. Remove
the 2 screws that hold the metal glass cap down (See Screw Locations Below).
Remove the 2 screws hold the metal glass cap in place.
metal glass cap
C
Remove the 2 metal “U”clips that hold the glass into its channel. The “U”clips are located to
the left and right under the metal glass cap.
Slide the glass up and out from the guide channel.
“U” Clip
D
Remove Fire Log Set & Fire Light Screen
!!Unplug The Heater Before Servicing!!
(Remember That The Edges Of The Metal Are Sharp. Use Caution)
Remove the 4 screws that hold the fire log set in place. There are 2 screws at each end of the
fire log set. These screws are accessed through holes in the metal case (See Screw Locations
Below).
Screws
Screws
D
Lift the fire log set up at one end. The log set may be wedged into the case. As you remove,
you may have to wiggle slightly to free it.
NOTE: The log set is made out of fiberglass. Applying excessive force may cause damage.
Otros manuales para F-15 Gen IV
1
Tabla de contenidos
Otros manuales de Chimenea de interior de Sun Heat
