Sun Bandit StorEdge 3900 Manual
Sun Microsystems, Inc.
4150 Network Circle
Santa Clara, CA 95054 U.S.A.
650-960-1300
Sun StorEdge™3900 and 6900
Series Installation and Service
Manual
Part No. 816-3244-10
February 2002, Revision A
Please
Recycle
Copyright 2002 Sun Microsystems, Inc., 4150 Network Circle• Santa Clara, CA 95054 USA. All rights reserved.
This product or document is protected by copyright and distributed under licenses restricting its use, copying, distribution, and decompilation.
No part of this product or document may be reproduced in any form by any means without prior written authorization of Sun and its licensors,
if any. Third-party software, including font technology, is copyrighted and licensed from Sun suppliers.
Parts of the product may be derived from Berkeley BSD systems, licensed from the University of California. UNIX is a registered trademark in
the U.S. and other countries, exclusively licensed through X/Open Company, Ltd. For Netscape Communicator™, the following notice applies:
Copyright 1995 Netscape Communications Corporation. All rights reserved.
Sun, Sun Microsystems, the Sun logo, AnswerBook2, docs.sun.com, StorEdge, and Solaris are trademarks, registered trademarks, or service
marks of Sun Microsystems, Inc. in the U.S. and other countries. All SPARC trademarks are used under license and are trademarks or registered
trademarks of SPARC International, Inc. in the U.S. and other countries. Products bearing SPARC trademarks are based upon an architecture
developed by Sun Microsystems, Inc.
The OPEN LOOK and Sun™ Graphical User Interface was developed by Sun Microsystems, Inc. for its users and licensees. Sun acknowledges
the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry. Sun
holds a non-exclusive license from Xerox to the Xerox Graphical User Interface, which license also covers Sun’s licensees who implement OPEN
LOOK GUIs and otherwise comply with Sun’s written license agreements.
RESTRICTEDRIGHTS: Use, duplication, or disclosure by the U.S. Government is subject to restrictions of FAR 52.227-14(g)(2)(6/87) and
FAR 52.227-19(6/87), or DFAR 252.227-7015(b)(6/95) and DFAR 227.7202-3(a).
DOCUMENTATION IS PROVIDED “AS IS” AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-
INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID.
Copyright 2002 Sun Microsystems, Inc., 4150 Network Circle• Santa Clara, CA 95054 Etats-Unis. Tous droits réservés.
Ce produit ou document est protégé par un copyright et distribué avec des licences qui en restreignent l’utilisation, la copie, la distribution, et la
décompilation. Aucune partie de ce produit ou document ne peut être reproduite sous aucune forme, par quelque moyen que ce soit, sans
l’autorisation préalable et écrite de Sun et de ses bailleurs de licence, s’il y en a. Le logiciel détenu par des tiers, et qui comprend la technologie
relative aux polices de caractères, est protégé par un copyright et licencié par des fournisseurs de Sun.
Des parties de ce produit pourront être dérivées des systèmes Berkeley BSD licenciés par l’Université de Californie. UNIX est une marque
déposée aux Etats-Unis et dans d’autres pays et licenciée exclusivement par X/Open Company, Ltd. La notice suivante est applicable à
Netscape Communicator™: Copyright 1995 Netscape Communications Corporation. Tous droits réservés.
Sun, Sun Microsystems, the Sun logo, AnswerBook2, docs.sun.com, StorEdge, et Solaris sont des marques de fabrique ou des marques
déposées, ou marques de service, de Sun Microsystems, Inc. aux Etats-Unis et dans d’autres pays. Toutes les marques SPARC sont utilisées sous
licence et sont des marques de fabrique ou des marques déposées de SPARC International, Inc. aux Etats-Unis et dans d’autres pays. Les
produits portant les marques SPARC sont basés sur une architecture développée par Sun Microsystems, Inc.
L’interface d’utilisation graphique OPEN LOOK et Sun™ a été développée par Sun Microsystems, Inc. pour ses utilisateurs et licenciés. Sun
reconnaît les efforts de pionniers de Xerox pour la recherche et le développement du concept des interfaces d’utilisation visuelle ou graphique
pour l’industrie de l’informatique. Sun détient une licence non exclusive de Xerox sur l’interface d’utilisation graphique Xerox, cette licence
couvrant également les licenciés de Sun qui mettent en place l’interface d’utilisation graphique OPEN LOOK et qui en outre se conforment aux
licences écrites de Sun.
CETTE PUBLICATION EST FOURNIE "EN L’ETAT" ET AUCUNE GARANTIE, EXPRESSE OU IMPLICITE, N’EST ACCORDEE, Y COMPRIS
DES GARANTIES CONCERNANT LA VALEUR MARCHANDE, L’APTITUDE DE LA PUBLICATION A REPONDRE A UNE UTILISATION
PARTICULIERE, OU LE FAIT QU’ELLE NE SOIT PAS CONTREFAISANTE DE PRODUIT DE TIERS. CE DENI DE GARANTIE NE
S’APPLIQUERAIT PAS, DANS LA MESURE OU IL SERAIT TENU JURIDIQUEMENT NUL ET NON AVENU.
-iii
Safety Agency Compliance
You must read the Sun StorEdge 3900 and 6900 Series Regulatory and Safety Compliance
Manual before beginning any procedure in this manual.
Please
Recycle
Contents v
Contents
Preface xiii
1. Introduction 1–1
1.1 Overview of this Manual 1–1
2. Installing the Storage System 2–1
2.1 System Field-Replacable Units 2–1
2.2 Unpacking the Storage System 2–2
2.3 Moving and Placing the Storage System 2–3
2.4 Adjusting the Leveling Pads 2–4
2.5 Installing the Stabilizer Legs 2–5
2.6 Installing the Floor Brackets 2–7
3. Cabling the Storage System 3–1
3.1 Preparing the Storage System for Cabling 3–1
3.2 Connecting the AC Power Cord 3–3
3.3 Connecting the Ground Strap 3–6
3.4 Connecting the Storage System to the Host 3–8
3.5 Reassembling the Storage System 3–14
4. Powering the Storage System On and Off 4–1
4.1 Powering On the Storage System 4–1
vi Sun StorEdge 3900 and 6900 Series Installation and Service Manual • February 2002
4.2 Powering Off the Storage System 4–5
5. Preparing for Service 5–1
5.1 Tools Required 5–1
5.2 Safety Requirements 5–1
5.3 Removing and Replacing the Front Door 5–2
5.3.1 Removing the Front Door 5–2
5.3.2 Replacing the Front Door 5–2
5.4 Removing and Replacing the Side Panel 5–3
5.4.1 Removing the Side Panel 5–3
5.4.2 Replacing the Side Panel 5–4
5.4.3 Opening the Back Door of the Storage System 5–4
6. Installing and Removing FRUs and FRU Default Configuration Settings 6–1
6.1 Tools Required 6–2
6.2 Safety Requirements 6–2
6.3 Sun StorEdge 3900 and 6900 Series Storage System Default Configuration
6–3
6.4 FRU Placement 6–9
6.5 Installing a FRU 6–14
6.6 Removing a FRU 6–17
6.7 Key Switch 6–18
6.7.1 Removing the Key Switch 6–18
6.7.2 Replacing the Key Switch 6–19
6.8 AC Input Cable Assembly 6–20
6.8.1 Removing the AC Input Cable Assembly 6–20
6.8.2 Replacing the AC Input Cable Assembly 6–21
6.9 Power Sequencer 6–22
6.9.1 Removing the Power Sequencer 6–22
6.9.2 Replacing the Power Sequencer 6–23
6.10 Service Processor Service Panel 6–23
Contents vii
6.10.1 Removing the Service Panel 6–27
6.10.2 Replacing the Service Panel 6–28
6.11 Sun StorEdge Network Fibre Channel Switch-8 6–28
6.11.1 Removing the 8-Port Fibre Channel Switch 6–28
6.11.2 Replacing the 8-Port Fibre Channel Switch 6–30
6.11.3 8-Port Fibre Channel Switch Configuration Parameters 6–32
6.11.4 Sun StorEdge 3910 Storage System 8-Port Fibre Channel Switch
Configuration 6–33
6.11.5 Sun StorEdge 6910 Storage System 8-Port Fibre Channel Switch
Configuration 6–33
6.12 Sun StorEdge Network Fibre Channel Switch-16 6–34
6.12.1 Removing the 16-Port Fibre Channel Switch 6–34
6.12.2 Replacing the 16-Port Fibre Channel Switch 6–36
6.12.3 16-Port Fibre Channel Switch Configuration Parameters 6–38
6.12.4 Sun StorEdge 3960 Storage System 16-Port Fibre Channel Switch
Configuration 6–39
6.12.5 Sun StorEdge 6960 Storage System 16-Port Fibre Channel Switch
Configuration 6–40
6.13 Service Processor 6–41
6.13.1 Removing the Service Processor 6–42
6.13.2 Replacing the Service Processor 6–42
6.14 Ethernet Hub 6–43
6.14.1 Removing the Ethernet Hub 6–43
6.14.2 Replacing the Ethernet Hub 6–43
6.14.3 Ethernet Hub Addressing Configuration 6–45
6.15 Virtualization Engine 6–46
6.15.1 Removing the Virtualization Engine 6–46
6.15.2 Replacing the Virtualization Engine 6–47
6.15.3 Standard Virtualization Engine Settings 6–47
6.15.4 Sun StorEdge 6910 Storage System Virtualization Engine Default
Settings 6–49
viii Sun StorEdge 3900 and 6900 Series Installation and Service Manual • February 2002
6.15.5 Sun StorEdge 6960 Storage System Virtualization Engine Default
Settings 6–49
6.16 Sun StorEdge T3+ Array 6–51
6.16.1 Sun StorEdge T3+ Array Base Configurations 6–52
6.16.2 Sun StorEdge T3+ Array Target ID and Host Name 6–53
6.16.3 Sun StorEdge T3+ Array Set Command Configuration Settings
6–53
6.16.4 Sun StorEdge T3+ System List Command Configuration 6–55
6.16.5 Sun StorEdge T3+ Array Miscellaneous Configuration
Parameters 6–55
6.17 Sun StorEdge Remote Response Program 6–56
6.17.1 Overview 6–56
6.17.2 Removing and Replacing the Sun StorEdge Remote Response
Hardware 6–57
6.17.3 Removing the Xylogics MicroAnnex Unit 6–60
6.17.4 Replacing the Xylogics MicroAnnex Unit 6–60
6.18 Troubleshooting the Installation 6–66
A. Product Specifications A–1
A.1 Physical Characteristics A–1
A.2 Physical Specifications A–2
A.3 Clearance and Service Access A–3
A.4 Power Sequencer Electrical Specifications A–4
A.5 Environmental Requirements A–4
B. Sun Storage System Part Numbers B–1
B.0.1 Sun Field Replaceable Units B–1
B.0.2 Sun StorEdge Storage Systems B–2
B.0.3 Explanation of Part Number TB3910-B2-1321 B–4
Figures ix
Figures
FIGURE 2-1 Leveling Pad 2–4
FIGURE 2-2 Stabilizer Legs 2–5
FIGURE 2-3 Installing the Right Stabilizer Leg 2–6
FIGURE 2-4 Adjusting the Leveling Pads on the Stabilizer Leg 2–6
FIGURE 2-5 Removing the Mounting Screws 2–7
FIGURE 2-6 Attaching the Floor Brackets 2–8
FIGURE 3-1 Location of Key Switch on Bottom Front Panel 3–2
FIGURE 3-2 Power Sequencer Control Panel 3–3
FIGURE 3-3 Connecting the AC Power Cord 3–5
FIGURE 3-4 Connecting the Ground Strap to the System Cabinet Power Sequencer 3–7
FIGURE 3-5 Connecting the Ground Strap to the Front Power Sequencer 3–8
FIGURE 3-6 Sun StorEdge 3910 Storage System Cabling 3–9
FIGURE 3-7 Sun StorEdge 6910 Storage System Cabling 3–10
FIGURE 3-8 Sun StorEdge 3960 Storage System Cabling 3–12
FIGURE 3-9 Sun StorEdge 6960 Subsystem Cabling 3–13
FIGURE 4-1 Location of Key Switch on Bottom Front Panel 4–2
FIGURE 4-2 AC Power Sequencer Control Panel 4–2
FIGURE 4-3 Front Sequencer Status Lights 4–3
FIGURE 5-1 Removing and Replacing the Side Panels 5–3
FIGURE 5-2 Opening the Back Door of the Storage System 5–4
Figures x
FIGURE 6-1 Sun StorEdge 3910 Storage system FRU Placement 6–10
FIGURE 6-2 Sun StorEdge 3960 Storage System FRU Placement 6–11
FIGURE 6-3 Sun StorEdge 6910 Storage System FRU Placement 6–12
FIGURE 6-4 Sun StorEdge 6960 Storage System FRU Placement 6–13
FIGURE 6-5 Filler Panel and Trim Strip Location 6–15
FIGURE 6-6 Power Cable Routing 6–16
FIGURE 6-7 Key Switch Cable Connector 6–18
FIGURE 6-8 Removing and Replacing the Key Switch 6–19
FIGURE 6-9 Removing the AC Power Cord 6–21
FIGURE 6-10 Removing the Power Sequencer 6–22
FIGURE 6-11 Service Processor Service Panel 6–24
FIGURE 6-12 Service Processor with Sun StorEdge Remote Response Hardware 6–59
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario