Studio Titan STA 06-105 Manual de usuario
STA 06-105 Folding Arm 1
CAUTION: Use supplied leather work gloves and safety glasses when handling the box,
when opening the box and when assembling the product.
HAZARD: Strapping is under tension and can jump when cut. Strapping and Buckles,
rotective Edging, lastic Walls, lastic Caps and roduct Components and parts should be
handled with care. Work slowly, use extra caution to avoid any sharp edges.
Additional Tools may be Required: The essential tools are included. The following tools
are recommended to be on site: Box Cutter, Scissors, Screw Driver, lyers or Adjustable
wrench, Metric Hex / Allen Key set
STA 06-105 Folding Arm 2
Transit Damage:
Each package is inspected prior to being shipped from the
warehouse to insure that is in perfect condition. The shipping
boxes are constructed using extra thick cardboard. Some
packaging includes engineered plastic walls and dense foam
to protect and absorb energy from reasonable drops and im-
pacts. If handled without care the boxes will show signs of
transit damage. While following the Assembly Steps carefully
inspect the contents.
If anything seems unusual !!!STOP!!! Send images to:
[email protected] for a second opinion. If there
are damaged OR Loose parts do not assemble the product
you may injure yourself. If the damage is noticeable such as
cracks or loose or broken parts contact your dealer for ex-
change. If the damage is minor or cosmetic and does not
compromise the safe assembly or operation of the product
send images of the parts that are affected to:
[email protected]. Arrangements will be made to
provide you with replacement parts to restore the product to
new condition.
STA 06-105 Folding Arm 3
Product Identification:
Product Nameplate Label is located on the vertical column assembly.
The label information is indicated below:
STUDIO TITAN AMERICA
No.[Model Number] - [Manufac ure Da e]
Impor ed by / Impor e par
STEPHANIE MCNEIL CORPORATION
250 Augus a Ave, Sui e 204
Toron o, ON M5T 2L7 CANADA
Manufac ured in / Fabrique en
SOUTH KOREA
Label examples are indicated below:
STA 06-105 Folding Arm 4
Intended use:
This product is intended for use by professional
and commercial photographers in a studio envi-
ronment with a high ceiling. The products are
designed to be used indoors on a floor that is
smooth hard flat and unobstructed.
CAUTION: This product is not recommended
for use by hobbyists or in a household environ-
ment with a low ceiling or carpeted floors. Car-
peting or pitted surfaces are not recommended
because of the increased rolling resistance
which can cause the stand to tip over. If the
surface is not ideal the stand must be moved
with CAUTION very slowly using both hands
one at the top and the other at the bottom to
steady the stand in order to prevent the stand
from tipping over. If the surface is not ideal
lower the load to waist level before moving the
stand. When using a accessories with the stand
we also recommend the use of sandbags or op-
tional leg weights attached to the legs at the
base to prevent tipping over. Ultimately it’s the
users responsibility to understand how the
stand operates and to use the stand within its
specification limits as intended to insure their
own safety and the safety of their equip-
ment. It is also recommended to use a short
tether cable to secure the camera to the stand
in the event that the head head plate attach-
ment stud or camera adapter plate comes loose
or fails. Some assembly may be required we
recommend using an assistant during the initial
product assembly. Please read all documenta-
tion prior to assembly.
STA 06-105 Folding Arm 5
Component Identification: STA 06-10 Folding Arm
STA 06-105 Folding Arm 6
! CAUTION ! Cross Threading Components:
Cross-threading components during assembly is not covered under war-
ranty.
Cross-threading is a term that describes damage that is caused when a
misaligned screw or knob thread is forced into a threaded hole. When this
occurs, threads are damaged and are no longer capable of proper opera-
tion. The remedy is replacement or repair of the damaged component/s.
AVOID cross-threading of mounting screws and knobs during assembly us-
ing this easy to follow procedure:
While standing in front of and looking into the threaded hole. Place the
screw or knob thread against the threaded hole. Using one hand, hold the
thread between your fingers. With the other hand hold the hex key like a
pencil or place your index finger in the center of the knob. Align the screw
or knob with the hole as indicated in the picture with the checkmark be-
low. Slowly turn it counter-clockwise or left, several turns, until you hear a
click or feel the start of the thread. Then proceed slowly, turning clockwise
or right, gently using only finger force to tighten the screw or knob. If you
feel increased resistance, the threads are not aligned, remove and start
procedure from the beginning again.
STA 06-105 Folding Arm 7
Component Identification: STA 06-10
Arm Pre-load Adjust-
ment Hex Screw
STA 06-105 Folding Arm 8
Component Identification: STA 06-10
Mounting Plates
STA 06-105 Folding Arm 9
Component Identification: STA 01-3 0R-MK2
Vertical Locking Lever and Head
Mount Plate
STA 06-105 Folding Arm 10
Assembly Steps:
1. The STA 06-105 Folding Arm is designed to be
used with the STA 01-350R-MK2 (Rotation) Com-
mercial Studio Camera Stand. The STA 06-105
folding arm can be attached to the Vertical car-
riage in two configurations explained below and
on the next page.
Configuration A: This configuration is recom-
mended if the STA 06-105 folding arm will be
used as the primary arm. In this configuration the
internal counterweight will be able to assist with
load balancing.
2. Configuration A: Remove the supplied STA 06-
105 folding arm mounting bracket. Locate the
original Mounting bracket for the Horizontal Arm /
Bar that was supplied with the STA 01-350R-MK2
(Rotation). Remove the Horizontal Arm / Bar from
the bracket and put the hardware aside. Turn the
Arm Locking knob counter-clockwise to detach
the Mounting plates from the STA 06-105 folding
arm. With the supplied hardware and hex key
tool attach the STA 06-105 folding arm Mounting
plates to the STA 01-350R-MK2 (Rotation) Mount-
ing Bracket.
3. Re-attach the Mounting Bracket to the STA 01-
350R-MK2 (Rotation) Vertical Carriage. Re-attach
the STA 06-105 folding arm to the mounting
plates and turn the Arm Locking knob clockwise.
Configuration: A
Este manual sirve para los siguientes modelos
1
Otros manuales de Accesorios para cámaras de Studio Titan
Studio Titan
Studio Titan STA 01-397 U Manual de usuario
Studio Titan
Studio Titan STA 01-360 Manual de usuario
Studio Titan
Studio Titan STA 01-350MK2 Manual de usuario
Studio Titan
Studio Titan STA-01-398 Manual de usuario
Studio Titan
Studio Titan STA 01-360MK2 Series Manual de usuario
Studio Titan
Studio Titan STA-C01-360 Manual de usuario
Studio Titan
Studio Titan STA 01-380 Series Manual de usuario
Studio Titan
Studio Titan STA 01-350R-MK2 Manual de usuario
