Strymon Flint Manual de usuario

Flint - tremolo & reverb
Contents
Knobs and Switches ......................................................................................... 3
Front Panel Controls - Tremolo ����������������������������������������������������������������������������������� 3
Front Panel Controls - Reverb ������������������������������������������������������������������������������������� 4
Rear Panel I/O and Control .............................................................................. 5
Live Edit Functions ........................................................................................... 7
Tremolo Boost/Cut ������������������������������������������������������������������������������������������������������� 7
Reverb Boost/Cut���������������������������������������������������������������������������������������������������������� 8
Tap Division ������������������������������������������������������������������������������������������������������������������� 9
Effect Order����������������������������������������������������������������������������������������������������������������� 10
Pre-Delay �������������������������������������������������������������������������������������������������������������������� 11
MIDI Clock Sync���������������������������������������������������������������������������������������������������������� 12
Respond/Ignore MIDI Expression ������������������������������������������������������������������������������ 13
Power Up Modes............................................................................................. 14
Input Level ������������������������������������������������������������������������������������������������������������������ 14
Bypass Mode��������������������������������������������������������������������������������������������������������������� 15
Spillover Mode ������������������������������������������������������������������������������������������������������������ 16
Configuring the EXP/MIDI Jack���������������������������������������������������������������������������������� 17
External Control ............................................................................................. 19
Expression Pedal Setup ��������������������������������������������������������������������������������������������� 19
Favorite Switch Setup and Compare Mode ��������������������������������������������������������������� 20
Tap Mode��������������������������������������������������������������������������������������������������������������������� 22
Configuring MultiSwitch Plus ������������������������������������������������������������������������������������ 23
Using MultiSwitch Plus ���������������������������������������������������������������������������������������������� 24
Saving Flint Presets with MultiSwitch Plus: ������������������������������������������������������������� 24
MIDI Functionality........................................................................................... 25
Configuring Flint to Use MIDI������������������������������������������������������������������������������������� 25
Saving Presets in MIDI Mode ������������������������������������������������������������������������������������� 30
MIDI Specifications......................................................................................... 31
MIDI Program Changes���������������������������������������������������������������������������������������������� 31
MIDI CCs ��������������������������������������������������������������������������������������������������������������������� 32
Factory Reset.................................................................................................. 33
Features.......................................................................................................... 35
Specifications ................................................................................................. 36
Power Adapter Requirements������������������������������������������������������������������������������������ 36
Appendix 1: Sample Settings ......................................................................... 37
Appendix 2: Power Up Modes Quick Reference ............................................. 39
General Options���������������������������������������������������������������������������������������������������������� 40
MIDI & Jack Options ��������������������������������������������������������������������������������������������������� 41
Appendix 3: Live Edit Controls Quick Reference............................................ 42
Strymon Non-Transferable Limited Warranty............................................... 44

pg 3
Flint - tremolo & reverb
Knobs and Switches
Front Panel Controls - Tremolo
INTENSITY
Controls the depth of the tremolo effect�
This is accomplished by varying the ampli-
tude of the LFO that controls the tremolo�
At minimum position, the LFO is off and no
tremolo effect is heard, but the signal still
travels through the tremolo “circuit�”
SPEED
Varies the tremolo LFO frequency from
slow to fast� The slow range is extended to
give lower trem speeds than were generally
available in the original, vintage offerings�
TREMOLO ON
Engages and bypasses the tremolo effect�
RED LED on indicates that the effect is
engaged� Bypass mode is true bypass by
default� See page 15 for details�
TREMOLO
Switches between three tremolo modes�
‘61 harm: harmonic band filtering that alternates low and high
frequencies for a hypnotic effect
‘63 tube: a smooth volume pulsing created by modulating the bias
point of the output tubes
‘65 photo: a sharper-edged volume effect achieved by using a
photocell and light-dependent resistor

pg 4
Flint - tremolo & reverb
Knobs and Switches
Front Panel Controls - Reverb
REVERB ON
Engages and bypasses the reverb effect� RED LED on
indicates that the effect is engaged� Bypass mode is true
bypass by default� See page 15 for details�
MIX
Controls the reverb wet mix from full
dry at minimum to full wet with no dry
signal at maximum� 50/50 mix is at the
3 o’clock position�
DECAY
Controls the duration of the reverber-
ated signal’s decay� The ‘70s and ‘80s
verbs will approach “infinite” decay at
maximum�
COLOR
Varies the reverb tone from darker at
low settings, to brighter at higher set-
tings� This is critical for dialing in the
sweet spot in front of a variety of amps�
REVERB
Switches between three different reverb types�
‘60s: full-size two-spring tank typical of those found on
vintage guitar amps
‘70s: electronic plate that uses multi-tap parallel delay
lines with filtered feedback paths
‘80s: studio digital microprocessor rack hall reverb with
modulating delay lines

pg 5
Flint - tremolo & reverb
Rear Panel I/O and Control
AUDIO INPUT SELECTOR
MONO: Use with a mono input signal, such as a guitar� Output is
stereo� Use OUT L for mono connection�
STEREO: Use with a stereo input signal� Output is stereo�
IN
High impedance, ultra low-
noise, discrete Class A JFET
preamp input� Use a TRS
stereo adapter/cable for stereo
input�
OUTPUTS
Low impedance stereo outputs�
Use OUT L for mono output�

pg 6
Flint - tremolo & reverb
Rear Panel I/O and Control (cont.)
9VDC
Use the included power
supply or an adapter with the
following rating:
• 9VDC, center negative
• 300mA minimum
USB
Computer connection for MIDI
control as well as for perform-
ing firmware updates�
EXP / MIDI
Multifunction communication jack for external control of Flint’s features
and functions� Can be set to operate in one of the following modes� (See
“Configuring the EXP/MIDI Jack” on page 17 for details�)
Expression Pedal mode (see page 19)�
Favorite mode (see page 20)�
Tap mode (see page 22)�
MIDI mode (see “Configuring MultiSwitch Plus” on page 23 or
“Saving Presets in MIDI Mode” on page 30)�

pg 7
Flint - tremolo & reverb
Live Edit Functions
Use the following steps to enter Live Edit mode to access several knobs’
secondary functions� Any of the following secondary functions can be
edited while in Live Edit mode�
Tremolo Boost/Cut
Allows you to adjust a +/- 3dB volume boost or cut when the Tremolo is
On�
1 Press and hold the REVERB ON footswitch to enter Live Edit mode�
Once both LEDs flash, release the footswitch�
TREMOLO
BOOST/CUT
2 Turn the INTENSITY (TREMOLO BOOST/CUT) knob to adjust the
amount of volume boost or cut for the Tremolo� Both ON LEDs indicate
your knob changes smoothly from -3dB cut (GREEN) at minimum to
+3dB boost (AMBER) at maximum� Unity gain is at the 12 o’clock
position (default)�
3 Press the REVERB ON footswitch to exit and store your Tremolo
Boost/Cut setting�
NOTE: The Tremolo Boost/Cut setting is saved per Favorite setting or MIDI
preset�

pg 8
Flint - tremolo & reverb
Live Edit Functions
Reverb Boost/Cut
Allows you to adjust a +/- 3dB volume boost or cut when the Reverb is
On�
1 Press and hold the REVERB ON footswitch to enter Live Edit mode�
Once both LEDs flash, release the footswitch�
REVERB
BOOST/CUT
2 Turn the MIX (REVERB BOOST/CUT) knob to adjust the amount of
boost or cut level of the Reverb� Both ON LEDs indicate your knob
changes smoothly from -3dB cut (GREEN) at minimum to +3dB
boost (AMBER) at maximum� Unity gain is at the 12 o’clock position
(default)�
3 Press the REVERB ON footswitch to exit and store your Reverb Boost/
Cut setting�
NOTE: The Reverb Boost/Cut setting is saved per Favorite setting or MIDI
preset�

pg 9
Flint - tremolo & reverb
Live Edit Functions
Tap Division
Sets the desired tap tempo, note sub-division for the Tremolo LFO
when an external TAP footswitch is used�
1 Press and hold the REVERB ON footswitch to enter Live Edit mode�
Once both LEDs flash, release the footswitch�
TAP DIVISION
2 Turn the SPEED (TAP DIVISION) knob to select the preferred division�
Both ON LEDs’ colors indicate your setting:
• 1/16 = RED
• Triplet = AMBER
• 1/8 = GREEN
• 1/4 = BLUE (default)
3 Press the REVERB ON footswitch to exit and store your Tap Division
setting�
NOTE: The Tap Division setting is saved per Favorite setting or MIDI preset

pg 10
Flint - tremolo & reverb
Live Edit Functions
Effect Order
Sets whether the signal travels through Reverb into Tremolo or
Tremolo into Reverb� The default is Reverb into Tremolo, as this is how
many vintage amplifier circuits worked�
1 Press and hold the REVERB ON footswitch to enter Live Edit mode�
Once both LEDs flash, release the footswitch�
EFFECT ORDER
2 Turn the DECAY (EFFECT ORDER) knob to select the order� The
TREMOLO ON LED indicates your setting:
• Reverb > Tremolo: left, GREEN (default)
• Tremolo > Reverb: right, RED
3 Press the REVERB ON footswitch to exit and store your Effect Order
setting�
NOTE: The Effect Order setting is saved per Favorite setting or MIDI preset�
Otros manuales para Flint
2
Tabla de contenidos
Otros manuales de Equipo de música de Strymon

Strymon
Strymon DIG Manual de usuario

Strymon
Strymon blueSky Manual de usuario

Strymon
Strymon DIG Manual de usuario

Strymon
Strymon Mobius Manual de usuario

Strymon
Strymon blueSky Manual de usuario

Strymon
Strymon TimeLine Manual de usuario

Strymon
Strymon Mobius Manual de usuario

Strymon
Strymon El Capistan Manual de usuario


















