Struers LaboForce-50 Manual de usuario
LaboForce-50
Instruction Manual
Original Instructions
Doc. no.: 16357025-01_C_en-us
Date of release: 2023.02.03
Copyright
The contents of this manual are the property of Struers ApS. Reproduction of any part of this manual without
the written permission of Struers ApS is not allowed.
All rights reserved. © Struers ApS 2023.02.03.
2 LaboForce-50
Table of Contents
1 About this manual 5
2 Safety 5
2.1 Intended use 5
2.2 LaboForce-50safety precautions 5
2.2.1 Read carefully before use 5
2.3 Safety messages 6
2.4 Safety messages in this manual 7
3 Getting started 7
3.1 Device description 7
3.2 LaboForce-50 8
4 Transport and storage 9
4.1 Long-term storage or shipping 9
5 Installation 9
5.1 Unpack the machine 9
5.2 Check the packing list 10
5.3 Installation - LaboForce-50 10
5.4 Adjusting the specimen mover 12
5.4.1 Insert a specimen mover plate 12
5.4.2 Adjust the height of the specimen mover plate 13
5.4.3 Adjusting the horizontal position of the specimen mover plate 13
5.4.4 Complete the adjustment 14
5.5 Noise and vibration levels 14
6 Operate the device 14
6.1 Control panel functions 14
7 Maintenance and service 15
7.1 General cleaning 15
7.2 Daily 16
7.3 Weekly 16
7.4 Monthly 16
7.4.1 LaboForce-50 - pressure feet 16
7.5 Spare parts 16
7.6 Service and repair 17
7.7 Disposal 17
LaboForce-50 3
1 About this manual
CAUTION
Struers equipment must only be used in connection with and as described in the
Instruction Manual supplied with the equipment.
Note
Read the Instruction Manual carefully before use.
Note
If you wish to view specific information in detail, see the online version of this
manual.
2 Safety
2.1 Intended use
The device is for professional semi-automatic materialographic preparation (grinding or polishing)
of materials for further materialographic inspection.
LaboForce-50 is intended to be used in combination with:
• LaboPol-20
• LaboPol-30
• LaboPol-60
Do not use the machine for
the following
Other equipment than stated in the section "Intended use".
Model LaboForce-50
2.2 LaboForce-50safety precautions
2.2.1 Read carefully before use
Ignoring this information and mishandling of the equipment can lead to severe bodily injuries and
material damage.
1 About this manual
LaboForce-50 5
General safety precautions
1. The machine must be installed in compliance with local safety regulations. All functions on the
machine and any connected equipment must be in working order.
2. This device must be mounted securely on the machine.
3. The operator must read the safety precautions and Instruction Manual, as well as relevant
sections of the manuals for any connected equipment and accessories.
4. If you observe malfunctions or hear unusual noises, switch off the machine and call technical
service.
5. In case of fire, alert bystanders and the fire brigade. Disconnect the electrical power supply. Use
a powder fire extinguisher. Do not use water.
6. This machine must be operated and maintained only by skilled/trained personnel.
7. Always switch off the electrical power supply and remove the plug or power cable before
dismantling the machine or installing additional components.
8. The machine must be disconnected from the electrical power supply before any service. Wait 5
minutes until residual potential on the capacitors is discharged.
9. Struers equipment must only be used in connection with and as described in the Instruction
Manual supplied with the equipment.
10. If the equipment is subjected to misuse, incorrect installation, alteration, neglect, accident or
incorrect repair, Struers will accept no responsibility for damage to the user or the equipment.
11. Dismantling of any part of the equipment, during service or repair, should always be performed
by a qualified technician (electromechanical, electronic, mechanical, pneumatic, etc.).
2.3 Safety messages
Struers uses the following signs to indicate potential hazards.
ELECTRICAL HAZARD
This sign indicates an electrical hazard which, if not avoided, will result in death or
serious injury.
DANGER
This sign indicates a hazard with a high level of risk which, if not avoided, will result in
death or serious injury.
WARNING
This sign indicates a hazard with a medium level of risk which, if not avoided, could
result in death or serious injury.
CAUTION
This sign indicates a hazard with a low level of risk which, if not avoided, could result
in minor or moderate injury.
6 LaboForce-50
2 Safety
CRUSHING HAZARD
This sign indicates a crushing hazard which, if not avoided, could result in minor,
moderate or serious injury.
HEAT HAZARD
This sign indicates a heat hazard which, if not avoided, can result in minor,
moderate or serious injury.
General messages
Note
This sign indicates that there is a risk of damage to property, or a need to proceed
with special care.
Hint
This sign indicates that additional information and hints are available.
2.4 Safety messages in this manual
WARNING
Struers equipment must only be used in connection with and as described in the
Instruction Manual supplied with the equipment.
CAUTION
Keep clear of rotating parts during operation.
CAUTION
When working at machines with rotating parts, take care to prevent clothes and/or
hair from being caught by the rotating parts.
3 Getting started
3.1 Device description
LaboForce-50 is a control panel/specimen mover unit which can be mounted on the following
machines for semi-automatic materialographic preparation (grinding/polishing): LaboPol-20,
LaboPol-30 and LaboPol-60.
The operator selects the grinding/polishing surface and the cooling fluid/abrasive suspension to
be applied.
A holding device for the preparation of specimens must be used with the specimen mover. The
holding device holds 4 specimens.
3 Getting started
LaboForce-50 7
The specimen mover head has pressurized feet which can be adjusted individually to keep the
specimens in place.
The operator decides which holding device should be used and the specimen force is adjusted
individually on the pressurized feet from the mover head to keep the specimens in place.
The operator sets the rotation speed of the preparation disc before starting the process.
The operator starts the machine by pressing the Start button on the control panel.
Cooling water is applied automatically when the operator opens the water tap. The operator applies
other fluids manually or by using a separate dosing unit.
The operator stops the machine by pressing the Stop button on the control panel.
The operator cleans the specimens before the next preparation step or inspection.
The machine must always be used with the splash guard in place.
If the emergency stop is activated, the power to all moving parts is cut.
3.2 LaboForce-50
Front view
AControl panel
BDisc speed control
CLED light (not shown)
DSpecimen mover head
EControl panel column
Rear view
ARotation switch (Specimen mover head)
BLocking handle
CType plate
8 LaboForce-50
3 Getting started
The specimen mover
AHousing
BForce indicators
CQuick release ring
DForce adjustment screw
EPressure feet
4 Transport and storage
If, at any time after the installation, you have to move the unit or place it in storage, there is a
number of guidelines we recommend that you follow.
• Package the unit securely before transportation. Insufficient packaging could cause damage
to the unit and will void the warranty. Contact Struers Service.
• We recommend that you use the original packaging and fittings.
4.1 Long-term storage or shipping
For instructions on how to prepare the unit for long-term storage or shipping, see the specific
machine manual.
Pay specific attention to the following:
• Disconnect the unit from the electrical power supply.
• Remove the control panel or specimen mover.
• Place the machine and accessories in their original packaging.
5 Installation
5.1 Unpack the machine
Note
We recommend that you keep all original packaging and fittings for future use.
4 Transport and storage
LaboForce-50 9
1. Cut the packing tape on the top of the box.
2. Remove the loose parts.
3. Remove the unit from the box.
5.2 Check the packing list
Optional accessories may be included in the packing box.
The packing box contains the following items:
Pcs. Description
1 LaboForce-50
1 Spacer and 2 M4 screws for mounting on LaboPol-30 and LaboPol-60
1 Spacing disc
1 Allen key for mounting the specimen mover plate
1 Instruction Manual set
5.3 Installation - LaboForce-50
Install the specimen mover in the connection hole of the machine.
Note
This device must be mounted securely on the machine.
Note
Do not use the speed control knob on the control panel to move the specimen mover.
Procedure - LaboPol-20
1. Remove the plastic disc protecting the communication cable.
2. Connect the communication cable on the column to the
connection port on the machine.
10 LaboForce-50
5 Installation
Tabla de contenidos
Otros manuales de Equipo de laboratorio de Struers
Struers
Struers LaboForce-3 Manual de usuario
Struers
Struers LaboPol-35 Manual de usuario
Struers
Struers Xmatic Manual de usuario
Struers
Struers LaboPol-30 Manual de usuario
Struers
Struers LaboForce-Mi Manual de usuario
Struers
Struers Duramin-100 Manual de usuario
Struers
Struers AbraPol-30 Manual de usuario
Struers
Struers LaboPol-60 Manual de usuario
Struers
Struers TegraDoser-5 Manual de usuario
Struers
Struers Abramin Manual de usuario
Struers
Struers AbraPlan-30 Manual de usuario
Struers
Struers Labotom-20 Manual de usuario
Struers
Struers LaboPol-20 Manual de usuario
Struers
Struers Accutom-100 Manual de usuario
Struers
Struers LaboPol-1 Manual de usuario
Struers
Struers LaboDoser-100 Manual de usuario
Struers
Struers LaboForce-Mi Manual de usuario
Struers
Struers LaboForce-100 Manual de usuario
Struers
Struers Lavamin Manual de usuario
Struers
Struers Epovac Manual de usuario
Manuales populares de Equipo de laboratorio de otras marcas
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manual de usuario
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manual de usuario
NI
NI PXI-5422 Manual
Collomix
Collomix Aqix Manual de usuario
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario
Ocean Insight
Ocean Insight FLAME-NIR+ Manual de usuario
