StreetStrider Summit 8r Manual de usuario
8r Owner’s Guide
2
ABOUT THIS OWNER’S MANUAL/ASSEMBLY GUIDE
This StreetStrider 8r Owner’s Manual/Assembly Guide contains important assembly, maintenance, safety and performance information.
It was written to help you get the most performance, comfort, enjoyment and safety out of your new StreetStrider. Keep this guide
handy for future reference.
IMPORTANT: If your StreetStrider was purchased unassembled, you should read this manual before you assemble it. The Limited
Warranty found in the Owner’s Guide Folder applies only to StreetStriders that have been assembled in full compliance with the
instructions in this Assembly Guide.
IMPORTANT: You should read this manual before you go out on your first ride.
Riding a StreetStrider can be a hazardous activity even under the best of circumstances. It is highly recommended that your first ride
on your new StreetStrider be taken in a controlled environment, away from cars, obstacles and other cyclists, and wearing your helmet.
Proper maintenance of your StreetStrider is your responsibility as it helps reduce the risk of injury. This manual contains many
IMPORTANT,CAUTION and WARNING statements concerning the consequences of
failure to maintain or inspect your StreetStrider. When inspecting your StreetStrider,
be certain to tighten all nuts and bolts properly. Under-tightening can result in
loosening, parts loss, and component damage. Over-tightened nuts and bolts can
break. StreetStrider parts have metric hardware- always use the correct tools.
IMPORTANT: It is impossible to predict every situation and condition that will occur
while StreetStriding. StreetStrider International LLC (the Company) has made no
representation about the safe use of the StreetStrider under all conditions. There
are risks associated with the use of any StreetStrider that cannot be predicted or
avoided, and the Company recommends safe and cautious riding.
WARNING
Failure to read and comply with
all assembly, safety, performance
and maintenance requirements and
warnings and unsafe or improper use
of the StreetStrider could result in
serious injury or death.
3
TABLE OF CONTENTS
PARTS IDENTIFICATION
Parts List
Parts Image Reference
UNPACKING & ASSEMBLY
Opening the Box
Unpacking the StreetStrider
Attaching the Front Wheels
Unfolding the Head Tube
Positioning the Strider Poles
Installing the Rear Wheel
Rotating the Crank Arms
Aligning the Front Wheels
Checking Brake Function
Adjusting the Rear Hub Shifting
Installing the Rear Rack
Folding the StreetStrider
SAFETY & MECHANICAL INFORMATION
Safety Equipment
Mechanical Safety Check
4
8
12
13
14
16
17
18
20
22
23
24
25
26
28
30
REGISTRATION
To activate your limited warranty, you will need to register your
StreetStrider online.
Register at: www.streetstrider.com/register-my-streetstrider
Please record your StreetStrider 8r serial number (found on
the frame around the bottom bracket; see photo) and other
information below. Please retain your sales receipt as proof of
purchase and keep with this information.
SERIAL #
DATE OF PURCHASE
4
PARTS IDENTIFICATION
PARTS LIST
The parts of the StreetStrider 8r are listed and labeled in the following table and images.
# DESCRIPTION HARDWARE SPECIFICATIONS QTY STATE
1 Main frame bone
2 Head tube
3 Cross bar, with joint #1
clamp
2.5 mm set screws M5 x P0.8 x L4 x W2.5 8 Snug but allow
clamp to swivel
4 Front beam
5 Fold joint, with silver
male cap screws and
silver female barrel nuts
6 mm hex screws:
upper and lower
middle
washers
5 mm barrel nuts
M8 x P1.25 x L30 x H13 x W6
M8 x P1.25 x L20 x H13 x W6
OD12 xID8 x T1
M8 x P1.25 x L16 x H12 x W5, barrel OD 10 mm
2
1
3
3
Tighten
Tighten
Tighten
6 Stride pole upper
8 Strider pole lower
9 Strider ski
10 Foot platform 4 mm screw under tape
10 mm lock nut
washer
M6 x P1.0 x L16 x H12 x W4, flat head
M6 x P1.0 x W10, nylon lock
OD12 x ID6 x T1
12
8
8
Tighten
Tighten
11 Seat stay
12 Chain stay
5
# DESCRIPTION HARDWARE SPECIFICATIONS QTY STATE
13 Rear rack 4 mm hex screw
washer
M5 x P0.8 x L12 x W4
OD12 x ID5 x T1
3
3
Tighten
14 Bottle cage 4 mm hex screw M5 x P0.8 x L12 x W4 2 Tighten
15 Pivot joint #1 clamp 4 mm hex screw M5 x P0.8 x L12 x W4 4 Tighten
16 Pivot joint #2 6 mm hex screw
washer
17 mm nut
M10 x P1.5 x L73.5 x H15 x W6
OD16 x ID10 x T1
M10 x P1.5 x L10 x W17, nylon lock
2
2
2
Snug but
allow joint
movement
17 Pivot joint #3 8 mm hex screw M8 x P1.0 x L15 x H12 x W8, 18 mm flange 2 Tighten
18 Hand grip
19 Twist grip shifter
20 Brake lever
21 Front wheel
22 Drum brake hub 19 mm axle bolt head M12 x P1.25 x L100 x W19 2 Snug but allow
wheel rotation
23 Steering linkage 12 mm flats
24 Crank arm 8 mm hex screw Tighten
25 Chainring with guard
26 Chain w/ master link
27 Rear wheel
28 Internal gear hub
29 Gear indicator
30 Brake lever clamp 5 mm hex screw Tighten
6
# DESCRIPTION HARDWARE SPECIFICATIONS QTY STATE
31 Brake lever w/
reach adjuster screw
Phillips or 2 mm hex
32 Twist shifter clamp 3 mm hex screw Tighten
33 Shifter cable adjuster
34 Brake cable adjuster
35 Brake lever locking pin
36 Front beam pivot 8 mm hex screws
6 mm hex screws
under beam
M8 x P1.0 x L15 x H12 x W8, 18 mm flange
M6 x P1.0 x L12 x H13 x W5
2
2
Tighten
Tighten
37 Spherical rod ends:
stud
stud nut
inboard adjuster
outboard adjuster
12 mm stud
13 mm nut
12 mm nut (LH thread)
12 mm nut (RH thread)
M8 x P1.25 x L10 x W13, nylon lock
M8 x P1.25 x L5 x W12 (LH, left hand)
M8 x P1.25 x L5 x W12 (RH, right hand)
4
4
2
2
Tighten
Tighten
Tighten
Tighten
38 King pin bolt in front
beam clevis
6 mm hex screw,
washer
17 mm nut
M10 x P1.5 x L75 x H15 x W6
OD16 x ID10 x T1
M10 x P1.5 x L10 x W17, nylon lock
2
2
2
Snug but allow
knuckle swivel
39 Steering knuckle w/
steering arm
40 Brake shoe plate w/
black bracket
41 Drum brake lever
PARTS LIST (cont.)
7
# DESCRIPTION HARDWARE SPECIFICATIONS QTY STATE
42 Brake cable housing
43 Brake cable w/
adjuster barrel nut
44 Cable end
45 Steering stop screw 6 mm hex head
12 mm nut
M8 x P1.25 x L20 x H13 x W6
M8 x P1.25 x L10 x W13, nylon lock
2
2
Tighten
Tighten
46 Bottom bracket square taper spindle
47 Crank bolt w/
One key release ring
8 mm hex
2 mm hex or spanner
M8 x P1.0 x L15 x H12 x W8 2
1
Tighten
Tighten, loc tite
48 Rear brake w/
mounting nut
cable housing adjuster
cable clamp
brake pads
5 mm hex
5 mm hex
4 mm hex
49 Rear drop out
50 Rear hub axle nut 15 mm 2 Tighten
51 Cassette pulley gear
alignment window for 8
speed
52 Shift cable fixing nut 10 mm 1 Tighten
M=OD of threads, mm L=length W=wrench fit, mm
P=pitch, threads/mm H=OD of head T=washer thickness, mm
SPECIFICATION KEY:
8
18
19 20
6
3
14
2
8
15
5
23
4
22
21
9
10
17
1
PARTS IDENTIFICATION
PARTS IMAGE REFERENCE
13
11
28
25
24
26
12
27
9
29
30
31
32
33
34
35
LOCKED UNLOCKED
5
23
16
36
4
36
10
INBOARD
PARTS IMAGE REFERENCE (cont.)
45
38
37
39
37
41 44
43
40
42
OUTBOARD 37
Otros manuales para Summit 8r
1
Tabla de contenidos
Otros manuales de Bicicleta de StreetStrider
