Stinger RT2 Manual de usuario
PLEASE READ!
This manual contains important information about product safety.
• Operation
RT2 CAP NAILER
OWNERS MANUAL
• Maintenance • Safety • Warranty
Revised 1/2/13
www.nationalnail.com
!
Distributed by: BEST MATERIALS ®
Ph: 800-474-7570, 602-272-8128 Fax: 602-272-8014
www.nationalnail.com
TABLE OF CONTENTS
• Important Information 1
• Warnings 2
• Tool Specifications 5
• Tool Assembly 5
• Loading the Tool 6
• Operating the Tool 7
• STINGER™ RT2 Schematic 9
• STINGER™ RT2 Parts List 13
• Hitachi® NV50A1 Parts List 17
• Maintenance and Storage 20
• Warranty 21
• Troubleshooting 22
i
www.nationalnail.com
This document serves as an addendum to the Hitachi NV50A1 Instruction Manual included with
this product. Please take the time to read and understand the information contained in the
NV50A1 instruction manual and STINGER RT2 Owners Manual before operating or maintaining
the STINGER RT2 Cap Nailer.
Improper use of this tool could result in serious injury or even death. Most accidents occur
because of the failure to observe basic safety rules and precautions. Basic safety precautions
are outlined in the Warningssection of this manual.
This product is intended for securing base sheet to wood decks only. Please do not use this
pneumatic tool for applications other than those specified.
This manual should be available for anyone who plans to operate the tool.
!
IMPORTANT INFORMATION
1
www.nationalnail.com
PERSONAL SAFETY ITEMS
1. Do not use tool prior to reading the Owners Manual.
!
WARNINGS
2. Always wear eye protection that confirms to ANSI requirements (Z87.1) and
provides protection against flying particles both from the front and side. Eye
protection should be worn by the operator and by others in the work area. Eye
protection is required to protect against flying fasteners and debris that could
possibly cause severe eye injury.
3. The employer is responsible to enforce the use of eye protection equipment by the tool
operator and all other personnel in the work area.
4. To prevent accidental injuries:
– Handle the tool with care
– Always assume that the tool contains fasteners
– Always disconnect the air hose from the STINGER™ RT2 when:
• loading nails and/or caps
• performing inspections, maintenance or repairs
• clearing a nail or collated cap jam
• the tool is not in use
• leaving the work area
• moving the STINGER RT2 to another work location
• handing the STINGER RT2 to another person
• storing the tool
– Never point the tool toward yourself or anyone else
– Never engage in horseplay
– Never hold or carry the tool with a finger on the trigger
– Never place a hand or any other part of the body in the fastener discharge area of
the tool while the air supply is connected
2
www.nationalnail.com
AIR SUPPLY AND CONNECTIONS
• Use only clean, regulated compressed air as a power source for this tool. Do not use bottle
gases, combustible gases or oxygen as a power source for the tool as the tool may explode.
• Do not use air supply pressures that exceed 120 PSI (8.28 bar or 8.4 kg/mm).
• Do not exceed the recommended maximum operating air pressure as tool wear will be
greatly increased. The air supply must be capable of maintaining the operating air pressure
of the tool. Pressure drops in the air supply can reduce the tools driving power.
• Use a pressure regulator and gauge to allow visual inspection of the air pressure being
delivered to the tool.
• Use air hoses that have rated pressures of up to 150% of the maximum pressure that can be
generated by the power source. The supply hose should contain 3/8fittings that will provide
quick disconnecting from the male plug on the tool.
• Use quick connect fittings that allow the tool to be unhooked from the air supply quickly and
easily.
• Do not use fittings that will not allow the tool to exhaust when the air supply is disconnected.
!
WARNINGS
3
www.nationalnail.com
WARNINGS
OPERATION OF THE TOOL
• Never inspect, maintain, repair, adjust, clear a jam or store the tool with the air connected.
• Never use the tool in proximity of flammable gases or liquids, as some tools will create
sparks that can be an ignition source for a fire or explosion.
• Always inspect the safety device for damage and proper operation, prior to operation.
• Never assume the tool is empty of fasteners.
• Never point the tool toward yourself or any other persons.
• Never cycle the tool unless it is in contact with the work-piece.
• Never use the tool as a hammer or wedging device or drop to the floor from any height.
• Never tamper with the safety device or use the tool if the safety device is not functioning
properly.
• Use only 1-1/4STINGER NailPac cap fasteners with the STINGER RT2 Cap Nailer.
Never use any fasteners that are not specified for use in the tool. The RT2 holds 1 reel of
steel caps (1500 caps) and 1 coil of collated nails (1500 nails).
4
!
www.nationalnail.com
TOOL SPECIFICATIONS
2. Install Nail Tray as shown. Secure
with Nail Peg and Socket Cap
Screw provided.
1. Raise Handle to desired height.
Tighten Socket Cap Screws.
Nail Tray
TOOL ASSEMBLY
Operating pressure 95-105 psi
Weight 43 lb. (with caps and nails)
Nail capacity 1,500 nails (1 coil)
Cap capacity 1,500 steel caps (1 reel)
Air consumption .035 ft3/cycle at 100 psi
(.99 ltr/cycle at 6.9 bar)
(.99 ltr/cycle at 7 kgf/cm2)
Air inlet 3/8 NPT
Fasteners STINGER NailPac (National Nail product number 0136072)
Consists of 2 coils of 1-1/4ring shank nails (1,500 nails per roll) and
2 reels of 1diameter steel caps (1,500 caps per reel).
Example:
500 shots/minute requires 17.5 ft3/ min
(17.5 cfm at 100 psi)
5
www.nationalnail.com
USE 1-1/4
STINGER NAILPAC CAP NAILS ONLY
LOADING THE TOOL
Lynch Pin Spool Hub
Disconnect air. Mount STINGER
NailPac cap reel on Spool Hub and
secure with Lynch Pin. Feed caps
into Washer Basket as shown.
Cap Basket
The image cannot be displayed. Your computer may not have enough memory to open the
image, or the image may have been corrupted. Restart your computer, and then open the file
again. If the red x still appears, you may have to delete the image and then insert it again.
Cap Feeder Assembly
Cycle Cap Feeder Assembly by
pressing down while pulling back
on the Picker Slide until the lead
cap advances to directly under
nailer nose as seen in Step 3.
1. 2.
3. 4.
Load wire-collated STINGER NailPac
nails into nail guide as instructed in
NV50A1 instruction manual.
The image cannot be displayed. Your computer may not have enough memory to open the image, or the image
may have been corrupted. Restart your computer, and then open the file again. If the red x still appears, you
may have to delete the image and then insert it again.
STINGER RT2 loaded. See next
section for operation.
6
www.nationalnail.com
OPERATING THE TOOL
3. The STINGER™ RT2 Air Preparation
Unit includes an Oil Mist Lubricator for
automatic nailer oiling and a Filter
Regulator to assist in supply air moisture
separation. Recommended pressure
setting on the Air Preparation Unit is
95-105 psi.
The Oil Mist Lubricator is adjusted at the
factory to supply approximately one drop
of oil for each fifty nails driven. A screw
located at the top of the Oil Mist
Lubricator allows for automatic nailer
oiling adjustments. Turn clockwise to
decrease, and counter clockwise to
increase.
3/8NPT male plug (not included)
Oil Mist Lubricator Filter Regulator
Unscrew the Oil Mist Lubricator site glass to service with non-detergent pneumatic tool
lubricant. The Filter Regulator site glass can be unscrewed or the button on the bottom
can be pushed to empty condensation.
1. Disconnect the air hose from the tool when:
• loading nails and/or caps
• performing inspection, maintenance or repair
• clearing a nail or collated cap jam
• the tool is not in use
• leaving the work area
• moving the tool to another work location
• handling the STINGER RT2 to another person
• storing the tool
2. For optimal performance, clean and lubricate cap feed moving parts and feed path before
each day of use with a dry silicone lubricant.
4. Depth of drive for nailing is adjusted primarily with the air pressure regulator; coarse
adjustments can be made by moving the Adjustable Wheel Assembly (#136).
7
www.nationalnail.com
OPERATING THE TOOL
6. The STINGER RT2 can be used in an automatic mode or manual mode. Setting the
Auto/Manual Toggle Valve to Manual (MAN) requires the Pushbutton Actuator to be
depressed each time the user desires to place a cap and nail. With Auto/Manual
Toggle Valve in the AUTO position and the push button actuator depressed, a cap will
be placed every 9or 18inches depending on the Cap Spacing Toggle Valve position
selected (9or 18.) A 6pattern is available only with the ten timing button pitch
wheel. For 6spacing, turn all ten timing buttons in and place the toggle switch in the
18position. The STINGER RT2 is now set to nail on 6and 9.
Note: Timing buttons should contact ball portion of the valve only. Turning them
in too far will result in valve unit damage.
Pushbutton Actuator Hose Holder
Toggle Valve (Auto/Manual) Toggle Valve (Cap Spacing)
4. The STINGER RT2 is a forward
operating tool The caps drag
behind the feed system as the tool
is pushed forward. Reverse
movement may cause jamming.
5. Feed the air hose through the
Hose Holder to aid in air hose
management.
This tool is set up for a 9and 18
pattern. You can change to a 6and 9
pattern by turning in the acutators with
the 5/16 allen wrench supplied with the
tool. Check to make sure the actuators
do not hit the casing for the roller ball
valves as this will damage them.
The jam nuts are in a preset position so
do not turn jam nuts on the screws.
8
Tabla de contenidos
Otros manuales de Herramientas eléctricas de Stinger
