Stinger Heigh10 Manual de usuario
HEIGH10 (UN1810) Installer Setup Guide
Accessing Installer Settings...............................................2
Installer Settings.................................................................3
Advanced Vehicle Settings.................................................3
Checking System Firmware Version.................................4
Updating Firmware............................................................5
SWC Settings ....................................................................8
Check/Update the HEIGH10 (UN1810) System Firmware:
Once installed and powered-up, the System Firmware needs to be up-to-date. Step-by-step
instructions for checking and updating the System Firmware can be found on Page 4 of this
Installer Set-Up Guide.
HEIGH10 User Guide:
The included User Guide Download postcard should be given to the end user, but you may want to
look over the User Guide to become familiar with all the user features and settings.
iGO Navigation (sold separately):
Be sure to insert an updated SE-P14 iGO Navigation card into the system before nalizing
installation. Visit: https://stingerelectronics.com/products/se-p14 for instruction on updating
the SE-P14 iGO navigation card.
Need Help?
If you have followed 1-4 above, and still have questions, reach out to our Technical Support Team:
Phone: 727-592-5991
Email: [email protected]
Chat: stingerelectronics.com
3
4
5
2
1Read the included Installation Guide:
The installation manual includes various installation methods, wiring diagrams
and species the correct hardware to use for the installation. Or, to view the
manual online, go to https://stingerelectronics.com/products/heigh10
Installers! Important Steps For Installation
This is a supplemental setup guide for the UN1810. This guide covers installer and system settings. Information
regarding the general operation, features and user settings of the HEIGH10 (UN1810) can be found in the User Guide.
ISG-UN1810 REV. 080822
®
®
SRK-JW18EH PAC Integration Kit
Jeep Wrangler JL | Gladiator JT
2
®
®
Accessing the Installer Settings
1. From any source, press the HOME Button
2. From the HOME MENU select Settings 3. Select System Settings
4. Select Installer Settings > Enter 5. Enter Passcode 0052 > OK
3
Installer Settings Advanced Vehicle Settings
FM Tuning Steps [100KH - 200KH]
Sets the FM radio tuning to 1 or 2 digit
increments. USA is 200KH and Europe
is 100KH.
System Information
Select to view current rmware revision.
(Page: 4)
Advanced Vehicle Settings
Select to access system dened vehicle
settings.
Amp Remote Out [PWR OFF - ACC]
PWR OFF: the Remote Turn On wire turns off
when the radio is turned off.
ACC: the Remote Turn On wire turns off when
accessory power is turned off. This is to keep
external equipment amps/DSP On if the vehicle
is equipped with parking sensor or other safety
equipment that produces safety chimes.
System Update
Select to update system rmware.
(Page: 5)
PAC Update
Select PAC Update to update the PAC APK
when an update is available.
Factory Reset
Resets radio to Vehicle Application maintaining
any updated version on Integration APK.
Master Reset
Resets radio to Universal Application wiping out
any updated version of Integration APK.
Steering Wheel Control
Select to program SWC when using the UN1810
analog steering wheel control inputs. (Page: 8)
Steering Wheel [Left - Right]
Denes how user interface will be congured,
mainly in Apple CarPlay.
Installer Setting > Advanced Vehicle Settings
SRK-JW18EH PAC Integration Kit
Jeep Wrangler JL | Gladiator JT
4
®
®
Checking System Firmware Version
1. Access the Installer Settings (Page: 2) and select
System Information to view rmware information.
2. Note the APP and System Versions and head over to the UN1810 product page on stingerelectronics.com.
Select the New Firmware Tab on the product page. The most current rmware will be listed with a date.
The 8 digits of the APP Version is the APP Version date code (YYYYMMDD). The 6 digits of the System
Version is the version date (YYMMDD). If the date code of either the APP or System rmware is older
than the current rmware on the website, proceed to Updating System Firmware.
Checking and updating the System Firmware and PAC Integration APK is an important step for
proper operation. This should be done rst before setting any system and vehicle settings as those
settings may be lost after an update.
5
Updating System Firmware
1. Format a USB Drive
Before copying the rmware le to a USB Flash Drive, the USB drive will need to be
formatted to FAT32 / MS-DOS(FAT)
USB Drive Format: Windows PC
A. Insert a 4GB+ USB Drive
D. Select FAT 32 File System and un-
check Quick Format and click Start.
B. Open File Explorer C. Right click on USB Drive & select
Format
USB Drive Format: Mac
A. Insert a 4GB+ USB Drive
D. Select MS-DOS(FAT) from the
format drop-down menu and click Erase
B. Launch the Disk Utility
App from the Utilities folder
C. Select the USB drive from the
“External” List and click Erase
SRK-JW18EH PAC Integration Kit
Jeep Wrangler JL | Gladiator JT
6
®
®
Updating System Firmware (cont.)
2. Download Firmware
Download the rmware le from StingerElectronics.com. Transfer the rmware le “as is” onto the formatted USB
drive. The le must be in the root directory of the USB drive. Do not unzip the le. See example A for Windows
and B for Mac.
A. Windows PC B. Mac
3. Install System Update
Insert the USB drive into either USB port on the radio.
NOTE: When updating the rmware, all settings will be reset to factory defaults.... station presets,
EQ presets, audio/crossover settings, time alignment, camera settings. If need be, record this
information before updating rmware.
A. Access the Installer Settings (Page: 2) and
select System Update > Update
The update will take 8-10 minutes.
Do not attempt to stop the update.
DO NOT turn off power. The system will be
damaged if power is lost during the
update process.
7
A. Access the Installer Settings (Page: 2) and
select System Update > Update
Updating System Firmware (cont.)
4. Factory Reset
When the update is complete and the display is on the Radio source, access the Installer Settings
(Page 2), and select Factory Reset > Reset. The reset process takes 1-2 minutes, when completed,
the unit will return to the Radio source.
5. Conrm Firmware Update
Conrm rmware update by following
the steps on page 4.
SRK-JW18EH PAC Integration Kit
Jeep Wrangler JL | Gladiator JT
8
®
®
Steering Wheel Control
Selecting Steering Wheel Control from Advanced
Vehicle Settings will access the SWC Settings.
The SWC Settings are used to program the
vehicles steering wheel controls when using the
UN1810 analog steering wheel control inputs.
NOTE: This does not need to be done when
using a SWC interface and the 3.5mm SWC
input on the UN1810. Refer to the SWC interface
intructions when using the 3.5mm SWC input.
Programming The Steering Wheel Controls:
1. On the SWC Settings page, select the desired
function by pressing the OK button.
The value will change from Unprogrammed to
Press Any Key
2. Press the desired button on the steering wheel.
The value will change to Programmed
9
Stinger is Power Brand of AAMP Global
15500 Lightwave, Clearwater, Florida 33760
P: 888-228-5560 | © 2022 AAMP Global
Technical Support:
Phone: 727-592-5991
Email: [email protected]
Chat: stingerelectronics.com
ISG-UN1810 REV. 080522
Otros manuales para Heigh10
8
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Sistema de vídeo para coche de Stinger
Stinger
Stinger HEIGH10 RB10RAM13B Manual de usuario
Stinger
Stinger STH10TACOM Manual de usuario
Stinger
Stinger Heigh10 Manual de usuario
Stinger
Stinger Heigh10 Manual de usuario
Stinger
Stinger HEIGH 10 Manual de usuario
Stinger
Stinger HEIGH10 SRK-JW18EH Manual de usuario
Stinger
Stinger Heigh10 Manual de usuario
Stinger
Stinger HEIGH10 UN1810E-FD5 Manual de usuario
Stinger
Stinger ELEV8 UN1880 Manual de usuario
Stinger
Stinger HEIGH10 UN1810E-FT3 Manual de usuario
Stinger
Stinger HEIGH10 SRK-RAM13H Manual de usuario
Stinger
Stinger VIP Manual de usuario
Stinger
Stinger HEIGH10 UN1810E-AU1 Manual de usuario
Stinger
Stinger HEIGH10 RB10RAM13B Manual de usuario
Stinger
Stinger HEIGH10 UN1810E-VW3 Manual de usuario
Stinger
Stinger HEIGH10 SRK-RAM13H Manual de usuario
Stinger
Stinger ELEV8 UN1880 Manual de usuario
Stinger
Stinger SPXRNGDASH Manual de usuario
Stinger
Stinger VIP Manual de usuario
Stinger
Stinger ELEV8 UN1880 Manual de usuario
